The burnup of spent fuel is one of the important management items that must be managed before storing the fuel in dry storage facilities, as well as for transportation and disposal in the future. Currently, the burnup of spent fuel is managed by calculating the design burnup at the time of design and measuring the real burnup using in-reactor measurement devices. Furthermore, to ensure the reliability of such data, the burnup of spent fuel can be measured using burnup measurement equipment to compare and analyze the data. In fact, KHNP is measuring the burnup of spent fuel using the burnup measurement equipment (SICOM-NG-FA) developed by ENUSA in Spain. The burnup measurement equipment analyzes the axial burnup profile of spent fuel using gamma and neutron detectors. Burnup measurement is performed by moving the spent fuel up and down inside the measurement equipment and measuring the burnup of the fuel surface facing the gamma and neutron detectors. This paper aims to compare the results of measuring the burnup of spent fuel on two sides versus four sides using the burnup measurement equipment.

Surface contaminants may attach to surfaces or objects in the radiation controlled area to cause radiation exposure, or spread out to the general environment by person and object exiting the radiation workplace. Accordingly, in radiological safety control, surface contamination monitoring is one of the important factors in workplace monitoring. When obtaining the measurement results for the monitoring, the results are accompanied by uncertainty since measurements contain numerous errors. Accordingly, the International Organization for Standardization (ISO) has published the ISO 7503 series which is comprehensive and detailed guidelines on the measurement and evaluation of surface contamination. ISO 7503-3 especially presents a mathematical model for the contamination measurement and provide calculation guidelines on measurement uncertainty evaluation, decision threshold and detection limit. This paper is focused on reevaluating and comparing the surface contamination monitoring method applied to radiation safety management practice and its results based on the measurement and evaluation method set by the International Organization for Standardization. The evaluation was performed in accordance with ISO 7503, and the current reporting method for measurement results was compared with the method recommended in ISO 11929 publication.

Since the implementation of the Odor Prevention Act in 2005, the number of odor complaints has continuously increased due to the increased interest in the living environment. The current odor control means is a concentrationbased method for the source of odor. That is why there is a difference between the odor sensitivity and the result of the odor measurement in the odor damage area. The government is considering the introduction of the grid method, which is the odor management method of Germany, as the method of odor investigation in the odor damage area in the second comprehensive Odor Prevention Policy (2019-2028). The grid method is receptor-based odor measurement method that investigators use to judge odors in the field, task that expensive and requires substantial manpower and time. To study an odor measurement method that is suitable for domestic conditions, this study compared the correlation between results based on the odor frequency concept grid method around the livestock facilities and the result of ammonia concentration measured by passive air sampler. The correlation coefficient (R) that is between the frequency of odor per spot for the entire odor and the ammonia concentration that was measured by passive air sampler was 0.65 which is relatively good. Among the entire odor detected by the grid method, the correlation coefficient (R) between the odor frequency selected only for livestock odor and the ammonia concentration was significantly increased to 0.80. In addition, the correlation between odor exposure (ECPexist) and the ammonia concentration for the overall odor was 0.81 (linear) and 0.86 (index). If only the livestock odors were selected, the correlation between odor exposure and the ammonia concentration was very high at 0.96 (linear) and 0.95 (index).

본 연구에서는 수집영상의 매 프레임 MPC(mm/pixel coefficient) 업데이팅을 통해 축 방향과 상관없이 왜곡영상에 따른 변위를 보정하는 기법에 관해 다루고자 한다. 영상의 강제적 왜곡을 위해 다양한 촬영 각도를 설정하여 실험을 진행하였으며, 캠코더의 설치 위치를 통해 0°~55°까지 5° 단위로 12가지 촬영 각도를 조정해가며 영상을 수집·분석하였다. 본 실험에 앞서 영상기반 변위계측의 유효성 평가를 위한 예비실험을 수행하였으며, GPS 및 가속도계와 계측결과를 비교해보았을 때, 영상기반 변위계측 시스템은 충분한 유효성을 갖는다고 판단된다. 촬영 각도 별로 수집된 영상을 분석하여 구조물의 최대 진폭 및 추정 진동수를 검출하였으며, 검출결과 비교를 통해 촬영 각도에 의한 영향을 판단하고자 하였다. 또한 계측된 자유 진동으로부터 감쇠비를 추정하여 추가적인 비교를 수행 하였다. 분석 결과 최대 진폭 기준 0.325mm, 오차율 기준 5.72%의 미소한 오차를 나타냈다. 진동수 추정에서도 촬영 각도 50°를 제외 하고 전체적으로 1% 미만의 오차율을 보이며 매우 유사한 추정 결과를 나타냈으며, 촬영 각도가 변화에 따른 감쇠비는 최소 1.025% 에서 최대 1.189%의 추정결과를 보이며 촬영 각도와 상관없이 전체적으로 유사한 감쇠비를 나타냈다.

All measurements include uncertain factors affecting the result in accordance with environment and conditions. In order to guarantee right decision making and quality improvement, these factors must be found and appropriate actions should be taken. This paper aims to estimate and analyze variabilities found in set-up and as well as measurement uncertainty when using CMM(Coordinate Measuring Machine). Two skilled operators were selected to individually measure a product which was a kind of main part of an engine called connecting rod cap. The results showed that at the least, 10 % was stable while at the most, 30 % was somewhat unstable regarding P, percentage of measuring errors. There was little difference between the two operators on measurement uncertainty expecially considering their degree of freedom based on their objective and subjective judgement of type B uncertainty despite the significant difference between them. Through this research, I have come to a conclusion that a much more detailed analysis on variation factors can be identified in general measurement by using CMM and the result of set-up variability demands specific investigation and efforts to improve operators’ skill or thorough examination on the method of setting product to minimize set-up variability later.

In this study, for the assesment of the seismic performance of a riser pipe with groove joints, in-plane cyclic loading tests were conducted using the pipe installation method suggested by NFPA13 and the allowable side sway of KBC. In addition, elbow and tee, which are weak parts of piping system, were separated and component test was performed under the same conditions.

With the recent earthquake measuring 5.4 in Pohang, attention is being raised to the effects of the structures caused by the earthquake. In this study, seismic effect of the tunnel structure was analyzed by the time history analysis method using the measurement results of the nearby structures. Most of the analysis results showed displacement and stress results of one tenth level of the artificial seismic wave using design seismic acceleration, and the actual field survey revealed that the effects of earthquakes were minor.

Tunnel were the inverse analysis based on the crown displacement calculated based on the generation of the result 63.80mm crown displacement measurement result. Three-dimensional inverse analysis up to the crown displacement was 60.7mm has occurred, which was considered similar to a two-dimensional inverse analysis 63.6mm.*

Tunnel were the inverse analysis based on the crown displacement calculated based on the generation of the result 63.80mm crown displacement measurement result. Inverse result was mainly to review the most significant impact on the interpretation weathed rock modulus of elasticity was smaller than the measurement when evaluating design values.*