이수식 쉴드 TBM 공법에서 발생하는 부산물인 필터케이크를 유동성 채움재로의 재활용 가능성을 평가하기 위해 다양한 기초 실험을 수행하였다. 필터케이크를 굵은골재 및 잔골재와 혼합하여, 필터케이크의 함량 비율을 증가시키면서 세 가 지 배합(Case 1, Case 2, Case 3)을 구성하였다. 강도 발현을 위한 바인더로는 보통 포틀랜드 시멘트를 사용하였으며, 물- 시멘트비(w/c)를 변화시켜 플로우 시험, 블리딩 시험, 압축강도 시험을 통해 유동성 채움재로서의 가능성을 평가하였다. 시험 결과, 필터케이크 함량이 증가할수록 혼합물의 유동성은 저하되었으며, 이를 보완하기 위해 혼합수의 양을 증가시 키며 적정한 범위의 유동성을 확보하도록 하였으나, 혼합수의 양이 많아질수록 압축강도가 크게 감소하는 경향을 보였 다. 특히, 필터케이크 함량이 가장 높은 Case 3에서는 이러한 현상이 두드러지게 나타났으며, 반면 필터케이크 함량이 적 은 Case 1에서는 상대적으로 높은 강도가 발현되었다. 또한, 필터케이크 함량이 적을수록 혼합물의 유동성은 혼합수량에 민감하게 변화하였다. 블리딩은 필터케이크의 혼합 비율에 영향을 받았으며, 필터케이크 함량이 가장 높은 Case 3에서 블리딩이 가장 적게 발생하였다. 이는 필터케이크의 높은 수분 흡수율이 블리딩 감소에 영향을 미친 것으로 판단된다. 즉, 유동성, 강도, 블리딩 사이의 균형을 맞추기 위한 적절한 배합비 설정을 통해 TBM 공법 부산물인 필터케이크는 유 동성 채움재로 재활용 가능성이 높을 것으로 평가하였다.

In order to respond to environmental pollution, developed countries, including Korea, have begun to conduct research to utilize hydrogen energy. For mass transfer of hydrogen energy, storage as liquid hydrogen is advantageous, and in this case, the volume can be reduced to 1/800. As such, the transportation technology of liquefied hydrogen for ships is expected to be needed in the near future, but there is no commercialized method yet. This study is a study on the technology to test the performance of the components constituting the membrane type storage container in a cryogenic environment as a preparation for the above. It is a study to find a way to respond by analyzing in advance the problems that may occur during the shear test of adhesives. Through this study, the limitations of ISO4587 were analyzed, and in order to cope with this, the specimen was supplemented so that fracture occurred in the adhesive, not the adhesive gripper, by using stainless steel, a low-temperature steel, to reinforce the thickness. Based on this, shear evaluation was performed under conditions lowered to minus 243℃, and it was confirmed that the breaking strength was higher at cryogenic temperatures.

고성능 콘크리트(HPC) 압축강도는 추가적인 시멘트질 재료의 사용으로 인해 예측하기 어렵고, 개선된 예측 모델의 개발이 필수적 이다. 따라서, 본 연구의 목적은 배깅과 스태킹을 결합한 앙상블 기법을 사용하여 HPC 압축강도 예측 모델을 개발하는 것이다. 이 논 문의 핵심적 기여는 기존 앙상블 기법인 배깅과 스태킹을 통합하여 새로운 앙상블 기법을 제시하고, 단일 기계학습 모델의 문제점을 해결하여 모델 예측 성능을 높이고자 한다. 단일 기계학습법으로 비선형 회귀분석, 서포트 벡터 머신, 인공신경망, 가우시안 프로세스 회귀를 사용하고, 앙상블 기법으로 배깅, 스태킹을 이용하였다. 결과적으로 본 연구에서 제안된 모델이 단일 기계학습 모델, 배깅 및 스태킹 모델보다 높은 정확도를 보였다. 이는 대표적인 4가지 성능 지표 비교를 통해 확인하였고, 제안된 방법의 유효성을 검증하였다.

To address the need for a suitable thermoplastic resin-based sizing agent for accommodating the increasing demands of carbon fiber-reinforced plastic, in this work, alcohol-soluble polyamide 6 (PA6) and silane were chemically combined in a certain ratio to improve the mechanical interface properties of the carbon fiber/PA6 composite, and the enhancement in the mechanical interface strength of the final composite according to the treatment time was confirmed. Carbon fiber surface properties were analyzed through ultrahigh-resolution field emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy, and Fourier transform infrared spectrometry. The tensile strength of carbon fibers before and after hybrid sizing treatment and the mechanical interfacial shear strength of the final composite were analyzed using tensile and universal testing machines, respectively. After the hybrid sizing treatment, the introduction of the sizing agent to the carbon fiber surface was confirmed through FE-SEM, and a simultaneous increase in the surface roughness was observed. Moreover, the interfacial adhesion was confirmed to increase significantly, as compared to that of the desized carbon fiber. Therefore, this modified sizing agent treatment serves as an effective method for improving the mechanical interfacial adhesion between the carbon fiber and the PA6 matrix.

Recently, 3D printing has been actively studied. A representative material in this 3D printing technology is plastic, and PLA, an eco-friendly material, is widely used. FDM is widely used as a way to output these PLA materials. However, this method lacks mechanical properties compared to injection-molded products as it is a method of stacking materials by melting. Therefore, in this study, using an FDM-type 3D printer, a tensile test was performed after printing a tensile specimen with PLA filament with the layer angle and layer density as control factors. After that, changes in tensile properties according to the layer angle and density were compared and evaluated. As a result, to improve the tensile strength, the layer density had to be considered, and to improve the elastic modulus, both the layer angle and the layer density had to be considered.

Based on the nonlinear static analysis and the approximate seismic evaluation method adopted in “Guidelines for seismic performance evaluation for existing buildings, two methods to calculate strength demand for retrofitting individual structural walls in unreinforced masonry buildings are proposed.” The displacement coefficient method to determine displacement demand from nonlinear static analysis results is used for the inverse calculation of overall strength demand required to reduce the displacement demand to a target value meeting the performance objective of the unreinforced masonry building to retrofit. A preliminary seismic evaluation method to screen out vulnerable buildings, of which detailed evaluation is necessary, is utilized to calculate overall strength demand without structural analysis based on the difference between the seismic demand and capacity. A system modification factor is introduced to the preliminary seismic evaluation method to reduce the strength demand considering inelastic deformation. The overall strength demand is distributed to the structural walls to retrofit based on the wall stiffness, including the remaining walls or otherwise. Four detached residential houses are modeled and analyzed using the nonlinear static and preliminary evaluation procedures to examine the proposed method.

증기운 폭발의 폭압을 예측하거나 위험성 분석을 위하여 다양한 폭압 산정법이 존재하지만 대표적으로 경험적 방법인 TNT 등가량 환산법과 멀티에너지법을 주로 사용한다. 멀티에너지법은 환경적 요인을 고려한 폭발강도계수를 사용한다. 본 연구에서는 문헌 분석 을 통하여 점화원 강도를 세분하고 강도분류를 확장하여 개선한 폭발강도계수 가이드라인을 제안하였다. 개선한 폭발강도계수 가이 드라인의 합리성 검증과 기존 Kinsella 가이드라인과의 비교를 위하여 실제 추정 폭압과 대조가 가능한 4가지의 증기운 폭발 사례를 적용하였다. 결과적으로 기존 Kinsella 가이드라인은 실제 추정 폭압에 비하여 광범위하거나 부정확한 폭압 산정 결과를 나타내는 것 으로 확인하였다. 반면, 개선한 폭발강도계수 가이드라인은 명확한 점화원의 강도 선정이 가능하고 분류의 확장을 통하여 더욱 세분 화된 계수 값의 선정이 가능함에 따라 실제 사례와 비교적 유사한 폭압 산정이 가능하다.

PURPOSES : The purpose of this study was to investigate the performance of additives that affect internal curing in order to reduce the damage occurring in concrete pavements. METHODS : SAP was used as an additive to reduce internal curing in concrete pavements. SAP is an additive that has a very high absorption rate which prevents concrete wrappers from externally draining water. To evaluate the internal curing performance according to the ratio of SAP, we identified the number of cracks and amount of abrasion reduction. RESULTS : Plastic shrinkage and durability of a concrete mixture with added SAP were evaluated. The following results were obtained: (1) SAP showed a tendency to reduce slumps due to absorption of the concrete mixture. (2) It was possible to verify that concrete condensation did not occur during the penetration resistance test and that the initial curing did not lead to reactions within the mixture. (3) Adding more than 0.6% of SAP for dry curing resulted in greater compressive strength at all ages than OPC, with the highest compression strength of 0.9% after 56 days. (4) Regarding abrasion resistance, it was found that adding SAP was 30~50% better than adding the OPC mixture, and at 0.9% compression strength, abrasion resistance showed the best performance. (5) In the chlorine ion immersion resistance experiment, the passing charge of the OPC mixture was rated “high,” but it was rated “normal” in SAP. The results showed that the addition of SAP improved the water density of concrete due to internal curing effects, and that it showed the greatest chlorine ion penetration resistance for a compressive strength of 0.9%. (6) Regarding plastic shrinkage resistance, cracks did not occur on the surface until the end of the experiment, but the plastic shrinkage rate upon addition of SAP was relatively low compared to that of the OPC mixture. CONCLUSIONS : Recent studies have shown that internal curing techniques can be applied using SAP to prevent shrinkage due to the loss of water and to decrease the effects of hydration. If internal curing effects are expressed using SAP, it is thought that contraction due to a loss of moisture and reduction in sign language reaction can be prevented.

본 연구는 테이핑 적용방법에 따른 근긴장도, 근경직도 및 악력의 변화를 알아보기 위해 실시하였다. 연구의 대상자는 20대 정상 성인 30명을 대상으로 하여 테이프를 늘리지 않고 붙이는 방법(non stretched taping)과 테이프를 늘려 붙이는 방법(stretched taping)을 통해 변인들을 측정하였다. 근긴장도와 근경직도는 Myoton pro 장비를 이용하여 측정하였으며, 악력계를 이용하여 악력을 측정하였다. 않은 자세에서 측정하였으며, 테이핑을 적용하기 전과 적용한 후를 대상자별로 임의로 순서를 정하여 측정하였고, 같은 동작에서 3번 측정하여 평균값을 사용하였다. 테이핑 적용에 따른 근긴장도, 근경직도 및 악력의 비교를 위하여 대응검정을 이용하여 분석하였으며, 중재 전·후에서 그룹간 차이를 보기 위하여 독립검정을 실시하였다. 본 연구의 결과 non stretched taping 적용과 stretched taping 적용 모두에서 근긴장도, 근경직도는 두 그룹 모두에서 통계적으로 유의한 감소를 보였으며, 악력은 두 그룹 모두에서 통계적으로 유의한 증가를 나타내었다. 그룹간 차이는 중재 전 근긴장도, 근경직도 및 악력은 차이가 나타나지 않았다. 중재 후 그룹간 차이는 근긴장도, 근경직도는 통계적으로 유의한 차이를 나타내지 않았으나, 악력의 경우 통계적으로 두 그룹간 유의한 차이가 나타났으며, stretched taping 그룹에서 더 높은 값을 나타내었다. 테이핑 적용 방법에 따른 근긴장도와 근경직도, 악력의 차이가 있기 때문에 테이핑 방법을 잘 적용하여 사용한다면 근육의 효과를 기대할 수 있을 것이다.

The purpose of this study is to investigate the optimum conditions of dispersion and strength to maximize the mechanical properties of woody cellulose nano–crystal (CNC). As a dispersing method, ultrasonic dispersing machine and magnetic stirrer were used as the mechanical dispersion method. The mixing ratio of cellulose nano-crystals (CNCs) was 0.2% and the dispersion time was 10 minutes. Steam curing was carried out for 6, 24 and 48 hours. Based on the experimental results, we will propose source technology regarding CNC for construction materials.

This paper presents the resizing method of columns and beams that considers column-to-beam strength ratios to simultaneously control the initial stiffness and ductility of steel moment frames. The proposed method minimizes the top-floor displacement of a structure while satisfying the constraint conditions with respect to the total structural weight and column-to-beam strength ratios. The design variable considered in this method is the sectional area of structural members, and the sequential quadratic programming(SQP) technique is used to obtain optimal results from the problem formulation. The unit load method is applied to determine the displacement participation factor of each member for the top floor lateral displacement; based on this, the sectional area of each member undergoes a resizing process to minimize the top-floor lateral displacement. Resizing members by using the displacement participation factor of each member leads to increasing the initial stiffness of the structure. Additionally, the proposed method enables the ductility control of a structure by adjusting the column-to-beam strength ratio. The applicability of the proposed optimal drift design method is validated by applying it to the steel moment frame example. As a result, it is confirmed that the initial stiffness and ductility could be controlled by the proposed method without the repetitive structural analysis and the increment of structural weights.

In this work, we studied the effects of electrochemical oxidation treatments of carbon fibers (CFs) on interfacial adhesion between CF and epoxy resin with various current densities. The surface morphologies and properties of the CFs before and after electrochemical-oxidation-treatment were characterized using field emission scanning electron microscopy, atomic force microscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and single-fiber contact angle. The mechanical interfacial shear strength of the CFs/epoxy matrix composites was investigated by using a micro-bond method. From the results, electrochemical oxidation treatment introduced oxygen functional groups and increased roughness on the fiber surface. The mechanical interfacial adhesion strength also showed higher values than that of an untreated CF-reinforced composite.

The clamping of torque shear high strength bolt is induced when the pin-tail is broken. However the tension forces induced shank of the bolt do not be known by now. This study focused to develop a quantitative method to identify the induced tension by analyzing the electric energy of which electric torque wrench (rpm 20) was applied to high strength bolt at the break of pin tail. Based on this co-relation between tension and accumulated current, the regressive analysis was derived. The error rate between tension and accumulated current was 5.06%.

The clamping of torque shear high strength bolt is induced when the pin-tail is broken. However the tension forces induced shank of the bolt do not be known by now. This study focused to develop a quantitative method to identify the induced tension by analyzing the electric energy of which electric torque wrench was applied to high strength bolt at the break of pin tail. Based on this co-relation between tension and accumulated current, the regressive analysis was derived. The error rate between tension and accumulated current was 2.24%.

본 연구는 해상에서의 안전사고의 경감과 국민의 생명을 보호하기 위한 목적으로 자체 연구를 수행하여 FRP의 수리공법인 Butt Joint, Lap Joint, V-Scarf Joint(12t, 16t, 20t), X-Scarf Joint(12t 16t, 20t)의 인장강도와 굽힘강도를 통해 이음방식에 따른 구조강도 특성을 실험하였다. 이음 방법에 따른 인장강도와 굽힘강도의 시험편을 종합 분석한 결과, 인장강도의 강도와 굽힘강도의 그래프 패턴은 비슷한 양상으로 증가와 감소를 하였으며, 인장강도와 굽힘강도 모두 X-Scarf-Butt Joint-V-Scarf-Lap Joint 순으로 강도가 우수하였다. 인장강도는 강도특성이 가장 우수한 X-Scarf라 하더라도 Basic Material의 57% 수준의 강도를 나타내었고 굽힘강도는 X-Scarf가 Basic Material의 77% 수준의 강도를 나타내었다. 종합적으로 Over-Lay 구분을 포함하여 X-Scarf 12t 이음이 인장강도, 굽힘강도 특성이 우수하였으며 Lap Joint가 가장 좋지 않았다. Scarf 이음시 Taper 길이에 따른 강도의 차이는 V-Scarf 이음은 Taper의 길이가 가장 큰 20t가 인장강도, 굽힘강도 특성이 우수한 반면 X-Scarf 이음은 Taper의 길이가 가장 짧은 12t가 인장강도, 굽힘강도 특성이 우수하여 상반되는 결과를 나타내었다. 선박에는 많은 Stress가 작용하여 시험편만을 가지고 실험한 본 연구와 직접적인 비교는 힘들지만, 재료의 가장 기본 특성을 인장강도와 굽힘강도 시험을 통해 확인할 수 있다. FRP 국부적인 수리 방법인 Butt Joint, Lap Joint, V-Scarf, X-Scarf 4가지의 이음방법에 따른 시험값과 모재 대비 감소되는 비율을 제시하였고 추가적으로 V-Scarf와 X-Scarf의 Taper 길이별 특성을 12t, 16t, 20t로 구분한 결과값을 제시함으로써 수리 현장에서의 위치별 특성에 맞는 수리 방법의 응용이 가능하도록 하였다.