Using UV nanoimprint lithography(UV-NIL), 1-dimensional(1-D) pattern structures were fabricated on a hybrid mixture thin film of lanthanum oxide and a UV-curable resin. 1-D pattern on a wafer fabricated by the laser interference lithography was transferred to polydimethylsiloxane and this is used as a mold of UV-NIL process. Conducting an X-ray photoelectron spectroscopy, C 1s and La 3d spectra were analyzed, and it was confirmed that hybrid thin film was successfully deposited on glass substrate. Also, transferred pattern structure was observed by using an atomic force microscopy. Through this, it was revealed that agglomerations between 1-D pattern were increased as UV irradiation time increased and this phenomenon disrupted the quality of NIL process. Additionally, liquid crystal(LC) cells with patterned hybrid thin films were fabricated and LC alignment performances were investigated. Using the polarizing optical microscopy and the crystal rotation method, LC alignment state and pretilt angles were observed. Consequently, the uniform homogeneous LC alignment was achieved at UV irradiation time of 1min and 3min where high resolution pattern transfer was observed.

A normal range of motion is essential for performing activities of daily living. The capsular pattern is the proportional motion restriction in range of motion during passive exercises due to tightness of the joint capsule. Although the capsular pattern is widely referred to in clinical practice, there is no scientific evidence to support the concept. In this review, the appropriateness of the capsular pattern for evaluation of joint pathology was assessed. In the Textbook of Orthopaedic Medicine written by Cyriax, the capsular pattern did not specify how much reduction in angular motion is considered motion restriction. As the definition proposed initially was unclear, different methods have been used in previous studies investigating capsular pattern. In addition, the capsular pattern described all the major joints of the human body, but only the hip joint, knee joint, and shoulder joint were studied in experimental studies. Sensitivity and specificity were reported in one study and were meaningful in specific pathologies (loss of extension to loss of flexion). There was no consensus on the reliability and validity. In summary, the capsular pattern suggested by Cyriax or Kaltenborn is not supported or applies only to certain conditions. Various components around a joint complement each other and provide stability to the joint. It is recommended that the therapist perform multiple assessments rather than rely on a single assessment when evaluating joints.

This research explores how imported automobile companies can develop their strategies to improve the outcome of their recalls. For this, the researchers analyzed patterns of recall demand, classified recall types based on the demand patterns and examined response strategies, considering plans on how to procure parts and induce customers to visit workshops, recall execution capacity and costs. As a result, recalls are classified into four types: U-type, reverse U-type, L- type and reverse L-type. Also, as determinants of the types, the following factors are further categorized into four types and 12 sub-types of recalls: the height of maximum demand, which indicates the volatility of recall demand; the number of peaks, which are the patterns of demand variations; and the tail length of the demand curve, which indicates the speed of recalls. The classification resulted in the following: L-type, or customer-driven recall, is the most common type of recalls, taking up 25 out of the total 36 cases, followed by five U-type, four reverse L-type, and two reverse U-type cases. Prior studies show that the types of recalls are determined by factors influencing recall execution rates: severity, the number of cars to be recalled, recall execution rate, government policies, time since model launch, and recall costs, etc. As a component demand forecast model for automobile recalls, this study estimated the ARIMA model. ARIMA models were shown in three models: ARIMA (1,0,0), ARIMA (0,0,1) and ARIMA (0,0,0). These all three ARIMA models appear to be significant for all recall patterns, indicating that the ARIMA model is very valid as a predictive model for car recall patterns. Based on the classification of recall types, we drew some strategic implications for recall response according to types of recalls. The conclusion section of this research suggests the implications for several aspects: how to improve the recall outcome (execution rate), customer satisfaction, brand image, recall costs, and response to the regulatory authority.

인간의 편의 향상과 경제성을 앞세운 중국은 수십 년 전부터 도시개발에 대한 환경오염, 도시 외곽지역 재개발 등의 문제가 끊임없이 논의되어 왔다. 이러한 녹지단절이나 종 다양성의 문제를 방지하기 위해 광역적 생태 네트워크가 요구되어지며 공간변동의 파악이 필요하다고 사료된다. 따라서 본 연구에서는 도시 확산이 빠르게 진행되고 있는 중국 중남부지역 ‘녹심’이라는 대도시권 녹지공간을 중심으로 토지피복도 및 경관 생태지수를 이용하여 시공간적 패턴변화와 경관다양성을 분석하고자 하였다. 1978-2019년의 Landsat 위성사진을 이용하여 ENVI 5.3과 ArcGIS 10.2를 통해 시계열의 경관요소를 유형화하였다. 경관 구조적·기능적 측면에서 객관적인 정량화하는 방법으로 FRAGSTATS를 통하여 경관지수를 정량화하여 산출하였다. 연구결과 1)이 지역의 경관은 1978년부터 오랜기간 토지변화에 따라 자연스럽게 형성되었고, 2)1989-2009년에는 택지개발이나 도로건설에 의해 주로 산림패턴에서 심각하게 파편화를 규명하였으며, 3)1999년 이후 시가지역의 경관지수에 따라 더욱 단순해지고 안정된 상태를 보였다. 4)수역이나 나지의 패치고립도가 높게 나타나고, 경관다양성에 부정적인 영향을 초래하였다. 5)2009년 이후 녹심계획과 함께 경관패턴은 전반적으로 규칙성이 있고 정형화되었다. 이와 같은 생태경관의 가치를 회복하는 것이 지속가능한 도시권 환경을 보전하는 데 가장 바람직할 것이며, 본 연구는 향후 녹심지역에 지속적으로 발전할 수 있는 매우 중요한 기초자료로 기대된다.

Laser induced surface activation (LISA) technology requires refined selection of process variables to fabricate conductive microcircuits on a general polymer material. Among the process variables, laser mode is one of the crucial factors to make a reliable conductor pattern. Here we compare the continuous wave (CW) laser mode with the pulse wave (PW) laser mode through determination of the surface roughness and circuit accuracy. In the CW laser mode, the surface roughness is pronounced during the implementation of the conductive circuit, which results in uneven plating. In the PW laser mode, the surface is relatively smooth and uniform, and the formed conductive circuit layer has few defects with excellent adhesion to the polymer material. As a result of a change of laser mode from CW to PW, the value of Ra of the polymer material decreases from 0.6 m to 0.2 m; the value of Ra after the plating process decreases from 0.8 m to 0.4 m, and a tight bonding force between the polymer source material and the conductive copper plating layer is achieved. In conclusion, this study shows that the PW laser process yields an excellent conductive circuit on a polymeric material.

Background: Weakness of the trunk muscles decreases the trunk control ability of stroke patients, which is significantly related to balance and gait. Objectives: To compare the impact of diagonal pattern self-exercise on an unstable surface and a stable surface for trunk rehabilitation on trunk control, balance, and gait ability in stroke patients. Design: Nonequivalent control group design. Methods: Twenty four participants were randomized into the experimental group (diagonal pattern self-exercise while sitting on an unstable surface, n=12) and the control group (diagonal pattern self-exercise while sitting on a stable surface, n=12). All interventions were conducted for 30 minutes, three times a week for four weeks, and the trunk impairment scale (TIS), berg balance scale (BBS), functional gait assessment (FGA), and G-walk were measured. Results: All groups indicated significant increases in all variables (TIS, BBS, FGA, cadence, speed, stride length) after four weeks. The TIS, BBS, FGA, cadence, gait speed, and stride length group-by-time were significantly different between the two groups. Conclusion: We found that, in stroke patients, diagonal pattern self-exercise on an unstable surface is a more effective method for improving trunk control, balance, and gait ability than diagonal pattern self-exercise on a stable surface.

This study was performed to provide fundamental data on the convenience foods purchase according to the food-related lifestyle. This study was conducted on 398 Chinese international students residing in Gyeonggi area between October and December 2019. Among the total 373 survey subjects, gender was 183 male students (49.1%) and 190 female students (50.9%). This study was conducted by questionnaire method with reference to previous studies. There are significant differences in economic pursuit and taste pursuit for delivery food use, economic pursuit and taste pursuit for delivery food information, health pursuit and taste pursuit in delivery food ordering method, and economic pursuit and convenience pursuit for delivery food use (p<0.05). Delivery food usage time was significantly different in convenience pursuit, health pursuit, eating out pursuit, and taste pursuit (p<0.05), and the delivery food preference menu was significantly different in economic pursuit, health pursuit, eating out pursuit, and taste pursuit (p<0.05). The menu positive factors among satisfaction factors showed statistically significant differences in economic pursuit (β=0.188, t=3.531) and health pursuit (β=0.160, t=3.099) among food related lifestyle factors. In conclusion, this study presented the desirable direction of delivery food usage in Chinese students.

MDPS control has been a difficult problem for the past two decades. Though there are many ways to control steering feeling, the MDPS control logic is still being upgraded or developed for steering feel improvement. A new point of view in MDPS is proposed by evolution logic, which is a new driver friendly improvement based on the analysis of driver’s driving pattern. As a result of the application of evolution logic, this paper shows that drivers behaviour effecting factors among MDPS parameters will efficiently lead to customers’ satisfaction.

An ecological study for species composition and abundance of the fish assemblages in the coastal waters of Gujora and Mangchi of Geoje, Korea was conducted using monthly larval collection by an RN80 net from June, 2018 to May, 2019. A total of the 5 Orders, 15 Families, 21 species were collected. The dominant species were Ammodytes japonicus and Engraulis japonicas. Gobiidae was the most dominant species in June, Spratelloides gracilis in July, Chelidonichthys sp. in August, Gobiidae in September, Repomucenus beniteguri in October, Sebastiscus marmoratus in November, Sebastiscus marmoratus and Hexagrammos otakii in December of 2018, Pleuronectes yokohamae in January, Ammodytes japonicus in Febraury, Engraulis japonicus in March, Sebastes sp. and Gobiidae in April and Engraulis japonicus in May of 2019. The highest number of species and individuals were found in July and the smallest in August. Thus, the diversity index was the highest in July and the lowest in August. As a result of the similarity by month was divided into Group I in January and February and Group II in April, June and September. The most dominant species in the Group I were the Ammodytes japonicus and Sebastes inermis, and the most dominant species in the Group II was Gobiidae.