The Semi-Rigid Pavement (SRP) mixture is composed of Gap Graded Asphalt (GGA) mixture (air void = 20~28%) and cement paste. By inserting cement paste into voids in GGA mixture, SRP can provide not only flexibility but also rigidity characteristics on pavement performance. SRP can mitigate pavement surface temperature increase during summer session, provide better smoothness and mitigate rutting distress due to heavy weight vehicles, successfully. In Japan, SRP is widely applied in cross section area, heavy vehicle parking lot and highway ticketing booth in highway network system. In South Korea, SRP was introduced and applied since 2005. However, still more researches and studies are needed to understand material characteristics and improve performance of SRP. Moreover, the current SRP system in South Korea merely follows and adapts the aggregate gradation information from Japan which needs to be amended and customized into original material (i.e. aggregate, binder and cement) situation of South Korea. In this paper, SRP system based on Stone Mastic Asphalt (SMA) mixture design originated from Korea Expressway Corporation (KEC) and enhanced cement paste with addition of fly-ash and slags was developed. In addition, an optimized proportion between asphalt mixture air voids and cement paste amount with consideration of economic benefit was introduced. Based on field evaluation process it can be said that the newly developed SRP system can successfully adapted not only in static site on highway: parking lots or ticketing booth, but also in dynamic site on highway: driving and wheel path.

현대 목조 구조물은 일반적으로 접합철물인 연결재를 이용하여 접합된다. 그리고 목조 구조물에서 다수의 연결재를 사용한 접합부는 반강접 접합부를 만든다. 목조 구조물에 접합부가 핀접합으로 설계될 경우에 접합부를 통해 전달되는 하중이 과소 평가되고 이것은 접합부의 저항능력 부족을 초래한다. 목조 구조물의 접합부를 완전 강접합으로 고려할 경우에 접합에 필요한 접합철물의 양이 과도하게 증가 할 수 있다. 이것은 미적인 요소 뿐만 아니라 시공성과 경제성을 저하시킨다. 접합부의 합리적인 강성에 대한 추정은 목조 구조물의 합리적인 접합부의 설계에 필수적인 요소이다. 이 논문은 목조 구조물의 구조설계를 쉽게 수행할 수 있도록 도움을 주기 위하여 2면 전단접합에 대하여 구조설계에서 널리 이용되는 상용 프로그램을 사용하여 접합부의 근사적인 강성을 나타낼 수 있는 해석 모델링 기법을 제안한다. 제안된 근사해석 모델링 기법은 휨 모멘트, 인장에 대한 실험 결과와 해석결과를 비교하여 접합부의 거동을 나타낼 수 있다는 것을 확인하였다.

본 논문에서는 반강접을 고려한 프레임 구조에서 강재 탄성계수의 불확실성이 프레임 구조의 비선형거동에 미치는 영향을 분석하였다. 강재 탄성계수의 불확실성의 확률분포는 정규분포로 모델링 하였으며, 이러한 확률적 물성치를 반강접 프레임의 비선형 거동에 적용할 수 있는 해석 프로그램을 개발하였다. 프레임의 비선형 거동 인수인 기하학적 비선형, 재료적 비선형, 그리고 접합부의 반강접에 의한 비선형 효과를 고려하여, Monte Carlo Simulation에 기반한 확률론적 해석을 수행하였다. 확률론적 해석을 위해 확률변수를 세 종류로 생성하여 사용하였다. 확정론적 해석의 결과는 기존의 연구 결과와 잘 일치하는 결과를 보였다. 확률론적 해석의 경우, 변위의 분산계수는 구조에 작용하는 하중이 증가함에 따라 증가하는 결과를 나타냈으며, 그 값은 프레임구조의 구조적 특성에 영향을 받는 것으로 나타났다.

본 연구는 보수성 그라우팅제를 사용하여 제조된 반강성포장의 성능과 보수성에 대한 평가를 실시한 결과이다. 실내 성능 시험 평가에는 2종류의 그라우팅제를 사용하였다. 시험 방법으로는 P로트 흐름치를 변화시키면서 압축강도(3시간 및 7일)와 휨 강도(7일)의 변화를 관찰하였다. 관찰결과 P로트 흐름치의 변화는 강도의 변화에 큰 영향을 미치지 않았으나 다소 영향이 있는 것으로 나타났으며, 그라우팅제의 종류에 따라서는 강도의 변화가 발생하는 것으로 나타났다. 반강성포장체에 대한 성능 시험은 모체 아스팔트포장의 공극률은 변화시키면서 실시하였다. 시험결과 아스팔트포장의 공극이 클수록 반강성포장체의 휨 강도가 크게 나타나서 휨 강도는 공극의 크기와 관련이 있는 것으로 발견되었다. 보수 성능 시험은 현장에 시공된 일반 아스팔트, 살수된 반강성포장 및 살수하지 않은 반강성포장을 비교하여 시험을 실시하였다. 시험결과 살수된 반강성포장은 일반 아스팔트포장의 최고 온도와 약 11℃, 살수하지 않은 반강성포장과는 4℃의 차이가 발생하여 반강성포장의 보수성으로 인한 포장체의 온도 상승 억제 효과를 확인할 수 있었다.

Conventional analysis and design of steel structures are performed using the assumption of a either fully rigid or pinned. However, every steel connection lies in between fully rigid and pinned connection. So, It is important to consider the connection for steel structure design. In this paper Computer-based second-order elastic analysis is used to calculate one story two bay and two story three bay for steel structures with semi-rigid connection. Genetic Algorithms(GAs) and Sequential Unconstrained Minized Technique(SUMT) dynamic programming is used to the method for optimum design of steel structures. The efficiency and validity of the developed continuous and discrete optimum design algorithm was verified by applying the algorithm to optimum design examples.

Phase change material (PCM) has been developed and applied in various fields as construction material. If the application of PCM as the semi-rigid pavement cement grout becomes available, it would be possible to control the occurrence of a micro crack due to the generation of hydration heat in the ultra rapid harding cement, and if the occurrence of a micro crack is reduced, it would be possible to improve the cohesion performance between asphalt matrix and grout as well as to compact the matrix of the pavement material, improving the durability. Therefore, the applicability review of PCM for the purpose of improving the semi-rigid pavement materials through the shrink reduction of ultra rapid harding cement used as the semi-rigid pavement cement grout was carried out in this study.

Phase change material (PCM) has been developed and applied in various fields as construction material. If the application of PCM as the semi-rigid pavement cement grout becomes available, it would be possible to control the occurrence of a micro crack due to the generation of hydration heat in the ultra rapid harding cement, and if the occurrence of a micro crack is reduced, it would be possible to improve the cohesion performance between asphalt matrix and grout as well as to compact the matrix of the pavement material, improving the durability. Therefore, the applicability review of PCM for the purpose of improving the semi-rigid pavement materials through the shrink reduction of ultra rapid harding cement used as the semi-rigid pavement cement grout was carried out in this

A study to apply phase change material(PCM) to rapid hardening cement paste forming semi-rigid pavement was carried out. The characteristics fresh and hardened paste were evaluated through the experiment for a total of 6 mixtures according to the cement type and the substitution of phase change material for acrylate. The fluidity by substituting phase change material for acrylate satisfied the target flow time of 10 to 13 seconds. In case of setting time, it was possible to secure the performance of rapid hardening cement by substituting phase change material, and if the substitution ratio over 60%, the initial set occurred 1 to 2 minutes faster than other mixtures. In case of compressive strength and bond strength, it showed similar strength characteristics with the plain mixture, and it satisfied both the target compressive and bonding strength of 36MPa and 2MPa. The mixture substituting phase change material showed higher resistance to chloride ion penetration than the mixture only using acrylate and the OPC level was insufficient. From the results of physical and mechanical performances of semi-rigid pavement cement paste, the phase change material substitution rate of 20% was effective in the range of this study.

Semi-rigid pavement is one of excellent paving methods adopting merits of asphalt-concrete and concrete paving. However, conventional paving methods were mainly used on the new constructed roads. Therefore, in this research we have examined the possibility of using the semi-rigid pavement on occupied roads. Also, confirmed the early-open possibility of pavement by applying the rapid hardening binding material to semi-rigid pavement.

In this paper, in order to evaluate the seismic performance on semi-rigid column-tree type connections, the experimental results and the finite element analysis results were compared. As a results, both results were considerably similar.

본 연구에서는 유황폴리머에멀젼 (SPE)을 반강성 포장용 주입재의 아크릴레이트 대체재로서 활용가능성과 성능향상재료 (PVA섬유)에 대한 역학적 성능과 내구성능을 평가하였다. 평가결과, 반강성 포장재의 충전률은 섬유의 혼입률이 증가함에 따라 충전률이 저하되었지만,모든 배합조건에서 평균 92~94%로 측정되어 목표 성능인 90%를 만족하였다. 반강성 포장재의 마샬안정도 값은 최대 25.4kN으로 측정되어 반강성 포장재의 국내 기준인 5.0 kN 보다 약 4.7배 우수한 것으로 나타났다. 반강성 포장재의 동적안정도 평가결과, 휠 트래킹시험에 따른 변형저항성은 SPE를 대체한 배합조건이 보다 우수하였고, 모든 배합조건에서 45분 이후에는 변형량이 일정한 값에 수렴되어 동적안정도가 31,500회/mm로 동일한 결과를 나타내었다. 파단변형률은 최대 0.53% 정도로 나타나 아스팔트 포장재보다 우수한 강성으로 나타났다. 마모저항성 및 충격저항성 검토결과 모든 배합조건에서 손실률이 9.8~6.0%로 나타나 우수한 내마모성을 나타내었으며, 섬유를 0.3% 혼입한 경우 혼입하지 않은 Plain에 비하여 2.82배의 내충격성 향상을 나타내었다. 역학적성능 및 내구성능 등을 모두 고려하여 볼 때, 이연구 범위에서는 SPE 대체율 30%가 적정 수준이고, 혼입률 0.3% 범위에서 PVA 섬유를 적용하면 우수한 인성을 갖는 반강성 포장재 제조가 가능 할 것으로 판단된다.

In this study, application of industrial by-products as an ultra rapid hardening cement substitute for semi-rigid pavement grout was evaluated. The examination of abrasion resistance showed that the loss ratio was 8.0~11.5% in every mixing condition, which indicates a good abrasion resistance.

the desulphurization process. To exploit this abundance, the applications of sulphur must be expanded. as excellent durability of reuse of leftover sulphur which has high potential for utilization in construction materials, the study is actively in progress. Meanwhile, there has been active research on semi-rigid pavements that draw on the strengths and overcome the weaknesses of asphalt and concrete pavements. Acrylate is used to prevent cracking but involves a high cost, thus, an alternative material is required. As such, this study presents methods on the reuse of leftover sulphur and examines the engineering performance of grout containing sulfur polymer emulsion (SPE) for use in semi-rigid pavements. Our analysis shows that grout in which 30% of acrylate is replaced with SPE has superior properties in terms of time of flow and strength compared to regular grout. However, performance declined when more than 50% of acrylate was replaced by SPE, indicating that the optimum replacement level is 30%. Through SEM analysis, we found that grout with utra harding cement in this study at three hours had similar hydration properties to that of Type 1 Ordinary Portland Cement (OPC) at seven days, and maintained the properties regardless of grout containing SPE. OPC and grout with a replacement level of 30% displayed similar levels of chloride invasion resistance, whereas grout without SPE was far less resistant. Within the scope of this paper, the optimum replacement level of acrylate with SPE was found to be 30% in consideration of various properties such as time of flow, strength, and chloride invasion resistance.

The purpose of this study is to evaluate the flexural property of semi-rigid pavement which is poured sulfur polymer emulsion into permeable open graded asphalt secured 15∼20 percentage ranges of porosity. From the bending test result, it was found that the flexural strength of the semi-rigid specimens were evaluated approximately 432% higher than that of the open graded asphalt specimens. And the strain of maximum load point was 38.8% lower than that of the open graded asphalt specimens.