The fuel fabrication facility has been built and is being operated by KAERI since licensing research reactor fuel fabrication in 2004. After almost 20 years of operation, outdated equipment for fabrication or inspection has been replaced by automated, digitalized ones to assure a higher quality of nuclear fuels. However, the generation of a large amount of radioactive waste is another concern for the replacement in terms of its volume and various types of it that should be categorized before disposal. The regulatory body, NSSC (Nuclear Safety and Security Commission) released a notice related to the classification of radioactive wastes, and most accessory equipment can be classified into the clearance levels, called self-disposal waste. In this study, the practice of self-disposal of metal radioactive waste is carried out to reduce its volume and downgrade its radioactivity. For metal radioactive waste, which is expected to occupy the most amount, analysis status and legal limitations were performed as follows: First, the disposal plan was established after an investigation of the use history for equipment. Second, those were classified by types of materials, and their surface radio-contamination was measured for checking self-disposable or not. After collecting data, the plan for the self-disposal was written and submitted to the Korea Institute of Nuclear Safety (KINS) for approval.

Se-79, a fission product of uranium, is present in spent nuclear fuel. Selenium is volatilized from the spent nuclear fuel during the pretreatment of pyroprocessing, and a filter composed of calcium oxide can capture gaseous selenium in the form of CaSeO3. Because Se-79 has a long half-life (3.27E5 years) and selenite ions have high mobility in groundwater, they must be immobilized in a chemically stable form for final disposal. This study used a composition of 50 TeO2 - 10 Al2O3 - 10 B2O3 - 10 Na2O - 10 CaO - 10 ZnO (mol%). High-purity powders of TeO2, Al2O3, H3BO3, Na2CO3, CaCO3, and ZnO were used as glass precursors. The mixed powders were placed in alumina crucibles and melted in an electric furnace under an ambient atmosphere at 800°C for 1 h before being cast on a carbon mold. The obtained glasses were ground into fine powders and then mixed with CaSeO3 powders. The powders were melted in alumina crucibles at 800°C for 1 h. To simulate a seleniumcaptured calcium filter, CaSeO3 was synthesized by a precipitation method using sodium selenite (Na2SeO3) and calcium nitrate (Ca(NO3)2) solutions. The glass samples were analyzed by an X-ray diffractometer (XRD). Retention of Se in tellurite glasses was analyzed by an X-ray fluorescence spectrometer (XRF) and inductively coupled plasma (ICP). The chemical durability of tellurite glass was evaluated through the PCT method.

In operating or permanently shut down nuclear power plants which were built between 1970s and 1990s, asbestos was widely used for ceiling materials, wall materials, and gaskets. Furthermore, it was mainly treated as a heat-resistant material like insulation. In Kori Unit 1, radioactive asbestos was replaced or removed through maintenance and repair in the containment building during the operation period of about 40 years, but radioactive asbestos still remains that need to be partially dismantled. Generally, it is more difficult to handle because it belongs to two different waste categories, radioactive waste and hazardous waste. In addition, the risk increases further due to radioactivity with the asbestos hazards itself. Therefore, it is very important to accurately determine the amount of radioactive asbestos waste and to evaluate the treatment method and disposal reduction rate before the decommissioning is started. According to the Korean Waste Management Act, three methods are recommended for the asbestos (hazardous waste) treatment: landfill, solidification, and high-temperature melting. Landfill is commonly used in Korea and the United States while high-temperature melting and solidification are additionally recommended only in Korea. Considering the situation in Korea, landfill is not appropriate due to the limitations of landfill capacity and potential risks (hazards still remain). Therefore, the other two methods can be considered sufficiently in terms of safety, detoxification, and reduction rate. This paper evaluates the amount of radioactive asbestos waste at Kori Unit 1 based on the actual asbestos building material data (as of February 2022) of the Asbestos Management Comprehensive Information Network. Vitrification is considered as a sufficient alternative for treating radioactive asbestos waste. And, it is checked whether the vitrified waste through the high-temperature melting method, plasma torch, meets the requirements such as detoxification, compressive strength and leachability for storage and disposal stability. It is expected to be useful to prepare a radioactive mixed waste management standard and to reduce the disposal cost through the reduction of final waste.

The number of dismantled nuclear facilities is increasing globally. Dismantling of nuclear facilities generates large amount of waste such as concrete, soil, and metal. Concrete waste accounts for 70% of the total amount of waste. Since hundreds of thousansds of tons of concrete waste generated, securing technology of reduction and recycling of waste is emerging as a very important issue. The objective of this study is to synthesize geopolymer using inorganic materials from cement fine powder in concrete waste. Dismantled concrete waste contains a large amount of calcium silicate hydrate(C-S-H), Ca(OH)2, SiO2, etc., which is an inorganic material required for the synthesis of geopolymer. SiO2 affects the compressive strength of the geopolymer and Ca(OH)2 affects the curing rate. A high concentration of alkali solution is used as an alkali activator, and alkali activator is necessary for the polymerzation reaction of metakaolinite. The experiment consists of three steps. The first step is to react with concrete waste and hydrochloric acid to extract ions. In the solid after filtration, SiO2 and Al2O3 are composed of 84.10%. It can be used instead of commercial SiO2 required for the synthesis of geopolymer. The second step is to add NaOH up to pH 10, impurities can be removed to extract Ca(OH)2 with high purity. The final step is to add NaOH up to pH 13, and Ca(OH)2 extraction. The alkali solution generated after the last reaction can be recycled into an alkali activator during the synthesis of the geopolymer. If dismantled concrete waste is recycled during geopolymer synthesized, the volume reduction rate of dismantled concrete waste is more than 50%. If you put the radioactive waste in the recycled solidification materials synthesis from concrete waste by dismantling of nuclear facilities, it is possible to reduce the amount of waste generated and disposal costs.

This study aimed to remove uranium (U(VI)) ions from sulfate-based acidic soil-washing effluent using the ion-exchange method. For effective ion exchange of U(VI) ions under acidic conditions, one chelate resin (Purolite S950) stable under low pH conditions and two anion-exchange resins (Ambersep 400 SO4 and 920U SO4) used in sulfuric acid leaching systems were selected. The exchange performance of the three selected ion-exchange resins for U(VI) ions was evaluated under various experimental conditions, including ion-exchange resin dosages, pH conditions, reaction times, and reaction temperatures. U(VI) ion exchange was consistent with the Langmuir model and followed pseudo-second-order kinetics. Thermodynamic experiments revealed that the U(VI) ion exchange by the ion-exchange resins is an endothermic and spontaneous process. On the other hand, U(VI) ions was effectively desorbed from the ion-exchange resins using 0.5 M H2SO4 or Na2CO3 solution. Overall, on the basis of the results of the present study, we propose that Purolite S950, Ambersep 400 SO4, and Ambersep 920U SO4 are ion-exchange resins that can be practically applied to effectively remove U(VI) ions from sulfate-based acidic soil-washing effluents.

Untreated waste is temporarily stored on the site of the nuclear power plant. In some nuclear power plants, saturation period of temporary storage waste is less than 10 years away. As untreated waste continues to be generated in nuclear power plants, it could also affect management of operations. Accordingly, CRI is developing the 3.5 generation plasma torch melting facility for waste treatment. The 3.5th generation plasma torch melting facility consists of melter, plasma torch, waste supply device, exhaust gas treatment facility, power supply, etc. Melter is composed of melting chamber for melting control and pyrolysis chamber for waste pretreatment, and dam-type discharge device is adopted to overflow the melt. Plasma torch is hollow type with reversed discharge, has a rating of megawatt class, and has two gas supply lines. It can be used in transfer mode, non-transfer mode and mixed mode. There are three types of device for waste supply. The first is a drum pusher for injecting 200 L drums, the second is a screw-type waste supply and hopper for injecting solid waste, and the third is a nozzle-type waste supply device for injecting liquid waste. Exhaust gas treatment facility was equipped with post combustion chamber, off-gas cooler, high-temperature filter, HEPA filter, reheater, scrubber, ID fan and etc. Power supply of plasma torch operation is designed with a capacity of 1.5 megawatt (Maximum) and consists of channels A and B. Transfer mode, non-transfer mode and mixing mode of plasma torch may be selected through the control of PLC. This paper introduces the composition and function of the 3.5th generation plasma torch melting facility of CRI. In order to solve the problems arising through the operation of the 3rd generation plasma torch melting facility, an optimization plan is applied.

Following a radioactive waste criterion and clearance level radioactive waste Act Article 2. “The radioactive wastes confirmed by the Commission as having concentration by nuclide not exceeding the value determined by the Commission through incineration, reclamation, recycling, etc”. The combustible clearance level radioactive wastes like lumbers are incinerated and non-combustible wastes like concreted are buried. The metals clearance level radioactive wastes are recycled after being re-molded. However, the clearance level radioactive waste with keeping its original forms is not common. Due to the nature of KAERI, the equipment are brought into the radiation-controlled zone for experiments. Those equipment are conservatively considered contaminated and categorized with radioactive waste following nuclear safety acts. In this case, the spectroscopy device which is clearance level radioactive waste is self-disposed for use in non-controlled areas. The 4 devices are composed of 3 gamma-ray spectroscopy and 1 alpha, beta counting system. Those devices were used for clearance level radioactive waste’s radioisotope analysis in Radioactive Waste Form Test Facility which is used in a separated room for analysis. This room will be released in nonradiation controlled area, therefore those devices will be moved to non-controlled area and keep using. Last April self-disposal was reported to the regulatory body and got acceptance last May. Those devices were moved to non-controlled area last July. This case will be good example for reuse equipment which stop using in radiation controlled area but can keep used.

With the aging of nuclear power plants (NPPs) in 37 countries around the world, 207 out of 437 NPPs have been permanently shutdown as of August 2022 according to the IAEA. In Korea, the decommissioning of NPPs is emerging as a challenge due to the permanent shutdown of Kori Unit 1 and Wolsong Unit 1. However, there are no cases of decommissioning activities for Heavy Water Reactor (HWR) such as Wolsong Unit 1 although most of the decommissioning technologies for Light Water Reactor (LWR) such as Kori Unit 1 have been developed and there are cases of overseas decommissioning activities. This study shows the development of a decommissioning waste amount/cost/process linkage program for decommissioning Pressurized Heavy Water Reactor (PHWR), i.e. CANDU NPPs. The proposed program is an integrated management program that can derive optimal processes from an economic and safety perspective when decommissioning PHWR based on 3D modeling of the structures and digital mock-up system that links the characteristic data of PHWR, equipment and construction methods. This program can be used to simulate the nuclear decommissioning activities in a virtual space in three dimensions, and to evaluate the decommissioning operation characteristics, waste amount, cost, and exposure dose to worker. In order to verify the results, our methods for calculating optimal decommissioning quantity, which are closely related to radiological impact on workers and cost reduction during decommissioning, were compared with the methods of the foreign specialized institution (NAGRA). The optimal decommissioning quantity can be calculated by classifying the radioactivity level through MCNP modeling of waste, investigating domestic disposal containers, and selecting cutting sizes, so that costs can be reduced according to the final disposal waste reduction. As the target waste to be decommissioning for comparative study with NAGRA, the calandria in PHWR was modeled using MCNP. For packaging waste container, NAGRA selected three (P2A, P3, MOSAIK), and we selected two (P2A, P3) and compared them. It is intended to develop an integrated management program to derive the optimal process for decommissioning PHWR by linking the optimal decommissioning quantity calculation methodology with the detailed studies on exposure dose to worker, decommissioning order, difficulty of work, and cost evaluation. As a result, it is considered that it can be used not only for PHWR but also for other types of NPPs decommissioning in the future to derive optimal results such as worker safety and cost reduction.

Radioactive waste is classified into Intermediate level, low level, and very low potential based on the amount of radioactivity per unit gram, that is, the concentration limit. This method of classifying radioactivity per unit weight is not a problem if all packaged wastes are homogeneous. However, the reality is that not all waste is homogeneous. Relative hotspots may exist. Also, when several items are mixed, if one item has a relatively higher concentration than other items, it can become a relative hotspot. In Korea, even if all nuclides in a single radioactive waste package satisfy the low level concentration limit, if even one nuclide exceeds the concentration limit, the radioactive waste package becomes the intermediate level. In case of the United States, the US NRC provides regulations related to obtaining license as well as presents the technical position on the average waste concentration called Concentration Averaging and Encapsulation Branch Technical Position (CA BTP). CA BTP classifies waste into four types : Blendable Waste, Encapsulated items, Single Discrete Items, and Mixture of Discrete Items, and presents each approach to concentration averaging. In general, this is a method that suggests an acceptable ratio in case of the waste, which relatively high concentration waste is mixed. In order to apply this in Korea, we compare the classification standards for low and Intermediatelevel waste in Korea and the United States, related laws and backgrounds, and the application methods of CA BTP.

Strong acidic wastewater containing a radionuclide is generated from the decontamination of radioactively contaminated wastes or equipment. This wastewater is generally treated though a precipitation process using an alkali (alkali earth) hydroxides. In this precipitation process, a significant amount of alkali (alkali earth) sulfates are generated, which is the reason for the increase in the radioactive waste generation. In this study, a method for separating only radionuclides and metal ions from the wastewater was evaluated. For this reason, precipitation behaviors of radionuclides and metal ions by hydrazine injections were investigated using equilibrium calculations. In addition, behaviors of hydrazine decomposition after removal of radionuclides and metal ions were analyzed for recycling the wastewater.

We developed a 100 kW Class Transferred Type Plasma Torch applicable for melting of noncombustible metal wastes. By employing reverse polarity discharge structures for hollow electrode plasma torch, a transferred type arc plasma was generated stably with long arc length higher than 10 cm at the arc currents of ~400 A and gas (N2) flow rate of ~50 lpm. High arc currents and high arc voltages caused by the increased arc length could input high power level of ~100 kW to the noncombustible metal wastes, enabling quick melting. In addition, relatively long arc length and low gas flow rates can help reduce the deposition of melted materials on the exit surface of the torch. Thanks to these features, the developed plasma torch is expected to be suitable for small-scaled and portable melting system.

KHNP-CRI has developed Mega-Watt Class PTM (Plasma Torch Melter) for the purpose of reducing the volume of radioactive waste and immobilizing or solidifying radioactive materials. About 1 MW PTM is a treatment technology that operates a plasma torch and puts drum-shaped waste into a melter and radioactive waste in the form of slag is discharged into a waste container. Since only the overflowing slag is discharged from the melter, the discharge is intermittent. Therefore, solidification occurs in the process of discharging the melt. It is difficult to accumulate evenly in the waste container, and there is also an empty space. Solid radioactive waste must be disposed of to meet the acceptance criteria for radioactive waste. Plasma-treated solid waste raised concerns about the requirements. The waste solidification output in a slag container gave us some concerns for the waste package’s solidification and encapsulation requirements. The plasma-treated solid waste process to meet the acceptance criteria will be cost and need time consuming. Thus, a induction heating will be introduced to meet solidification requirements and test criteria of the solidification waste for the waste package disposal.

In this study, the process of compressing/packaging the spent filters of Kori Unit 1, which was conceptually presented in the previous study, is advanced so that disposal suitability for each step can be secure efficiently. In particular, the differences between the previous study and this study are that the disposable filters are screened using an In-Situ Object Counting System (ISOCS), and the method of collecting representative samples for development of scaling factor is specified. The process of compressing/packaging the spent filters consists of 7 stages as follows. 1) Collecting: The spent filters temporarily stored in the filter room are collected by dose and type remotely using a robot system to minimize the radiation exposure of workers according to a pre-established packaging plan. 2) Screening: The gamma activity concentration of the spent filters received by the robot system is measured by ISOCS. The spent filters below the low-level waste concentration limit and the surface dose are transferred into the compression system, while the others are returned in the filter room again. 3) Sampling: The external perforator drilling/cutting the filter was developed for sampling required for the new scaling factors. Since the sampling is collected remotely, the risk of exposure to workers can be reduced. The newly developed scaling factor will be used to verify the disposal suitability of the packages. 4) Compression: According to the pre-established plan, the spent filter collected by dose and type, is supplied to the compression system considering the dose and radionuclide inventory. Whether to additionally store the compressed filter in the drum is determined by checking the accumulated dose. 5) Immobilization: Immobilization with a safety material is necessary when inhomogeneous wastes, like spent filters, have the total radionuclide concentration with a half-life of more than 20 years is 74,000 Bq/g or more and for filling rate or non-dispersible treatment of particulates. 6) Packaging and Analysis: Waste information is labelled onto the package after the measurements of surface dose rate and surface contamination. Finally, using the drum assay system, the gamma radionuclide concentration is measured to identify at least 95% of the total radioactivity concentration of the package. 7) Temporary Storage and Delivery: The packages are moved to temporary storage in the plant prior to disposal. After establishing the plan for delivery and applying for a takeover request to KORAD, if the acceptance inspection is passed, the packages are transported to the disposal facility.

In this work, we report the basic performance of a 100 kW class mobile plasma melting system consisting of two 24-ft commercial containers, each in charge of the plasma utilities and melting process. In this system, a 100 kW class transferred type plasma torch has been installed together with a crucible having an inner volume of 2,884 cm3. Filling the inner volume of the crucible with the simulated metal waste, such as bolts and nuts, melting tests have been carried out for 5 min by varying plasma input power from 50 kW to 100 kW. By measuring the volume of metal waste before and after melting test, then, the volume reduction rates were estimated and discussed.

Glass wool, the primary material of insulation, is composed of glass fibers and is used to insulate the temperature of steam generators and pipes in nuclear power plants. Glass fiber is widely adopted as a substitute for asbestos classified as a carcinogen. The insulations used in nuclear power plants are classified as radioactive waste and most of the insulation is Very Low-Level Waste (VLLW). It is packaged in a 200 L drum the same as a Dry Active Waste (DAW). In the case of the insulations, it is packaged in a vinyl bag and then charged into the drum for securing additional safety because of the fine particle size of the fiberglass. A safety assessment of the disposal facility should be considered to dispose of radioactive waste. As a result of analyzing overseas Waste Acceptance Criteria (WAC), there is no case that has a separate limitation for glass fiber. Also, in order to confirm that glass fibers can be treated in the same manner as DAW, research related to the diffusion of glass fibers into the environment was conducted in this paper. It was confirmed that the glass fiber was precipitated due to the low flow velocity of groundwater in the Gyeongju radioactive waste repository and did not spread to the surrounding environment due to the effect of the engineering barrier. Therefore, the glass fiber has no special issue and can be treated in the same way as a DAW. In addition, it can be disposed of in the disposal facility by securing sufficient radiological safety as VLLW.

The decommissioning waste generated during the dismantling of a nuclear power plant has various types and radioactivity levels and is characterized by being generated in a large amount in a short time. For the safe and efficient management of decommissioning waste with these characteristics, the Korea Radioactive waste Agency (KORAD) is developing a large container for decommissioning waste. And the Waste Certification Program (WCP) requirement was developed for the development of a Waste certification program for nuclear power plant operators that can prove whether the transfer/ acceptance criteria are satisfied at the step of generation of decommissioning waste packages. The radioactive waste profile, which is a waste quality certification document required by the WCP requirements, allows the KORAD to confirm that the disposition suitability evaluation was performed for each process of decommissioning waste and radiological characteristic data were evaluated appropriately. Therefore in this study, in order to propose a draft of a radioactive waste profile for large packages of decommissioning waste, overseas cases and the draft radioactive waste profile of the WCP requirements was analyzed. In addition, it was attempted to increase the utility of the derived waste profile by clearly suggesting the treatment methods for each waste stream considering the physical and radioactive characteristics evaluation methods of large decommissioning waste packages. The proposed large decommissioning waste profile can be used in the future development of a nuclear power plant operator’s decommissioning waste certification program, as well as KORAD’s a disposal facility safety evaluation and improvement of the waste tracking management system (WTS).

In the present work, a three-phase AC arc plasma torch system is proposed to separate inorganic radioactive materials from the organic liquid waste. For this purpose, first, assuming the resistance of arc plasma ranges between 0.1 and 0.2 ohm, we designed a three-phase AC arc plasma power supply with the power level of 20 kW. Then, a three phase arc plasma torch consisting of three carbon rods with the diameter of 20 mm was designed and mounted on a cylindrical combustion chamber with the inner diameter of 150 mm. Detail design and basic performance of the plasma system were presented and discussed for application to the treatment of radioactive slurry wastes.

During and after the construction of LILW disposal facilities, the decrease of groundwater head potential has been monitored. In addition, an increase of the electrical conductivity (EC) has been observed in several monitoring wells installed along the coastal coastline. Monitoring activity for groundwater head potential and hydrogeochemical properties is important to reduce the uncertainty in the evaluation of groundwater flow characteristics. However, the data observed in the monitoring wells are spatial point data, so there is a limit to the dimension. Several researchers evaluated groundwater head potential changes and seawater intrusion (SWI) potential for disposal sites using groundwater flow modeling. In case of groundwater flow modeling results for SWI, there is a spatial limit in directly comparing the EC observed in the monitoring wells with the modeling results. In a recent study, it was confirmed that the response of the long-range ground penetraiing radar (GPR) system was severely attenuated in the presence of saline groundwater. In order to reduce the spatial constraint of the groundwater monitoring wells for SWI, the characteristics of SWI within the disposal facility site by using the the results of a recent study of the long-range GPR system were investigated and evaluated in this study.

HANARO, a multi-purpose research reactor, uses a reflector as heavy water to obtain high neutron flux. Therefore, two ion exchangers were installed to manage the heavy water quality of the reflector system. The operator of HANARO manages it according to the limit value (Conductivity: less than 0.5 mS/m, pH: 5.5~6.5), and if the limit value is not satisfied, the resin must be replaced. The reflector system is in the enclosed structure and it is designed to delay the release of tritium to the outside. Tritium is produced by a nuclear reaction between neutrons and deuterium. Tritium is inhaled into the body in the form of water or vapor, which is likely to cause internal exposure problem. In addition, since tritium spreads to other regions, thorough management is required. Therefore, HANARO measures and manages tritium in Rx and RCI using the bubbler collection method. In this paper, the change in the behavior of tritium due to the replacement of the reflector ion exchanger resin was analyzed. Due to the increase in conductivity of the reflector, the ion exchanger resin was replaced on March 3, 2022. Therefore, the concentration of tritium was measured to be about 5 times higher than usual. It did not exceed the emission limit, and the concentration values of tritium is stably managed by constant monitoring and analysis.

In a nuclear power plant, the activated corrosion products are deposited on the reactor coolant system. The activated corrosion products must be removed to reduce the radiation exposure to workers before maintaining or decommissioning of the nuclear power plant. In order to remove the remove the activated duplex oxide layer generated on the reactor coolant system in the pressurized water reactor (PWR), the Cyclic SP (Sulfuric acid/Permanganate)-HyBRID (Hydrazine Based Reductive metal Ion Decontamination) process developed by KAERI (Korea Atomic Energy Research Institute) can be used. After applying the Cyclic SP-HyBRID process, a sulfate-rich waste powder containing the radionuclide is generated, and the radioactive powder has to be stabilized for final disposal. In the previous study, it was confirmed that the low-temperature sintering method can be applied to immobilize the sulfate-rich waste powder. Thus, immobilization of the Cyclic SP-HyBRID process waste powder was carried out by the low-temperature sintering method using a low melting point glass, and the physicochemical and radiological characteristics of a waste form were evaluated in this study. As a result, the compressive strength of the waste form increased with increasing sintering temperature and sintering time. It is considered that the result was caused by the difference in the band gap between the bismuth borate and zinc borate, which are the products during the sintering process. It was verified that the physical stability was maintained after the 107 Gy of irradiation test. In addition, it was confirmed that the radioactive metal hydroxides contained in the waste powder converted to metal oxide forms, which have the lower solubility, at the sintering temperature. Finally, the waste form was evaluated as a low-level radioactive waste from the concentration of radionuclides contained in the waste form.