To investigate the physiological responses to naturally occurring winter freezing stress in creeping bentgrass, changes in carbohydrates were monitored during winter period. Turf quality and leaf growth was nearly parallel with temperature fluctuation. Th
콘크리트 암거와 같은 지중구조물의 뒷채움시에 부등침하를 줄이기 위해서는 양질의 뒷채움 재료사용과 대형진동 다짐장비를 이용한 정밀한 다짐을 실시하는 것이 중요하다. 또한 효과적인 정밀 다짐은 진동 롤러의 강한 진동을 함께 구조물부에 근접하여 다지는 것이 필요하다. 그러나, 이와 같은 다짐방법은 과도한 충격하중 발생으로 구조물의 벽체균열 발생을 유발할 수 있다. 본 논문에서는 콘크리트 암거의 뒷채움 시공을 위하여 충격완화재의 종류와 다짐방법을 변화하여 다짐시의 구조물에 발생하는 다짐토압을 현장계측을 통하여 분석하였다. 타이어칩과 발포 폴리 스틸렌을 사용한 패널들을 뒷채움 다짐시공전 암거 벽면에 부착하였다. 충격완화재 Type A(Rubber)와 Type B(EPS)의 성능 비교를 위한 실내시험 결과 Type A는 Type B보다 작은 탄성계수와 큰 재료감쇠를 가지고 있어 보다 큰 충격완화효과를 기대할 수 있는 것으로 나타났다. 다짐장비는 대부분 큰 다짐에너지를 위하여 고주파수인 30Hz를 적용하였다. 현장계측 결과로부터 다짐하중에 의한 동적 수평토압의 크기는 다짐장비의 가진여부, 측정깊이, 다짐장비 이격거리 및 다짐방향에 의존하고 있었다. 암거의 동적 수평토압 측정결과로부터 롤러 다짐장비를 콘크리트 구조물에 직각방향으로 다짐작업을 실시하는 것이 수평방향으로 다짐하는 것 보다 다짐효과를 증가하는 것으로 나타났다.
In the presence of incident waves with different frequencies, there are second order sum and difference frequency wane exciting forces due to the nonlinearty of the incident waves. Although the magnitudes of these nonlinear forces are small, they act at sum and difference frequencies away from those of the incident waves. So, the second order sum and difference frequency wane loads occurring close to the natural frequencies of TLPs often give greater contributions to high and low frequency resonant responses. The components of the second order forces which depend on first order quantities have been evaluated using the three dimensional source distribution method. The numerical results of time domain motion analysis for the nonlinear wave exciting forces in regular waves are compared with the numerical ones of frequency domain analysis. The results of comparison confirmed the validity of the proposed approach.
상부벽식-하부골조구조(복합구조)는 상.하부 구조물의 서로 다른 구조형식으로 인해 전이층 부근에서 질량 및 강성의 큰 차이를 보인다. 이러한 복합구조의 특징은 일반적으로 강성, 질량 및 기하학적 수직 비정형성을 갖게 된다. 본 연구에서는 복합구조물의 상부층수가 변화하는 네 가지 해석모델을 선정하여 탄소성 정적 및 동적 해석을 수행하고 해석결과를 통해 구조물의 탄소성 응답특성을 살펴보고자 한다. 본 연구의 결론은 다음과 같다. 1) 탄소성 정적해석에서는 하부골조 구조의 보와기둥의 항복힌지가 상부벽식구조의 층수 변화에 상관없이 전 모델에 걸쳐 비슷한 크기의 설계용 밑면전단력에서 항복이 발생되었고 그 분포 또한 비슷하였다. 그러나 상부벽식구조의 경우 전단벽이 고층화될수록 coupling beam에서 설계용 밑면전단력 V에 대해서도 휨항복한지가 발생되었다. 2) 탄소성 동적해석으로부터는 하부골조의 일부층의 보는 55gal의 작은 지진동에서 소성이 발생되었고 상부벽식구조의 경우 coupling beam과 전이층 상부의 전단벽에서 소성변형이 집중되었다. 3) 탄소성 해석으로부터 상부벽식구조의 층수가 낮아질수록 하부골조구조의 층강성이 상대적으로 줄어들게 되어 하부골조에서 연약층(soft story) 현상이 나타났다.
본 논문에서는 구조물의 안전성과 경제성을 함께 도모하도록 하기 위하여 모드 해석법을 이용하여 비틀림 거동을 하는 구조물의 동적 거동을 정적 하중으로 치환할 경우에 대한 횡하중 중심점을 가정하고, 횡하중 중심점과 구조물의 강도 중심을 일치시키도록 구조물의 설계 편심을 조절하는 방법을 제안한다. 그리고 제안된 방법에 의해 구조물을 설계하였을 경우, 다른 내진 기준에 의해 설계된 구조물과 비교하여 지나친 추가 연성도를 요구하지 않는다는 것을 보여준다.
현재 국내에서 개발중인 액체금속로 원자로구조물의 내진설계 및 지진해석을 위하여 원자로내부에 존재하는 유체-구조물 상호작용을 고려한 단순지진해석 모델링 개발이 필수적이다. 이를 위하여 본 논문에서는 유체속에 잠긴 동축원통 구조물의 유체부가질량에 대한 이론적 배경을 검토하였으며 기존의 유체부가질량법을 고려하여 시간이력 지진응답해석을 수행할 수 있는 Runge-Kutta 수치해석 알고리즘을 사용한 해석코드를 개발하였다. 개발된 지진해석코드를 사용하여 유체속에 잠긴 두개의 동축원통 구조물의 진동특성과 지진응답에 대한 유체부가질량의 영향을 살펴보았다. 적용예로서 두개의 동축원통에 대한 단순지진해석모델을 가정하고 유체부가질량을 고려한 진동특성해석과 지진응답해석을 수행한 결과 유체가 채워진 동축원통 구조물은 유체와의 상호작용으로 인하여 구조물의 진동특성과 지진응답특성이 크게 영향을 받으며 지진응답해석시 연계항을 포함한 유체부가질량의 영향을 신중하게 고려할 필요가 있는 것으로 나타났다.
본 논문에서는 지하수의 영향을 고려하여 발파로 인한 폭발하중에 대한 지하공동구조체의 3차원 동적해석을 수행하였다. 지하공동 주변 암반체는 13.5%의 공극율을 갖는 석회암으로 가정하였으며, 동일한 폭발하중에 대해 주변 암반체의 공극이 완전히 건조한 경우와 이 공극이 완전 포화된 경우로 나누어 해석을 수행하였다. 수치해석결과 지하공동구조체가 포화된 암반체에 위치하는 경우가 건조한 암반체에 위치하는 경우에 비해 속도, 변위, 응력이 모두 크게 발생하였다. 그리고 포화된 암반체의 지하공동구조체 부근에서는 전단파괴의 가능성이 발생함을 확인할 수 있었다.
자동차 경량화를 지향하는 초경량차체 기술 중에서 합체박판기술을 이용한 수 있는 일련의 최적설계 기법을 제안하고 기존의 자동차 도어 내판에 적용하여 경량화를 수행하였다. 먼저, 내판에 부착되는 보강재를 제거한 후 취약해진 강성을 보강하기 위한 파트 선정을 위해 위상 최적설계를 수행하여 대략적인 파트 분포를 결정하였다. 그 다음 상세설계 단계로서 각 파트의 두께는 치수 최적설계를 이용하여 정하고, 형상 최적설계로 최종 용접선을 결정하였다. 이러한 일련의 최적화를 위해 상용 소프트웨어인 GENESIS가 사용되었다.
While the equilibrium behaviour of surfactant solution is well studied, the understanding of the kinetics and pathways of structural transition under nonequilibrium conditions is only begining to develop. Attention has recently been directed mainly towards micellar kinectics, transitions between micellar and lamellar phases, vesicle fusion, and phases separation in microemulsions. This progress has profited greatly from developments that have taken place in various techniques and instruments.
In general, the cutting pattern of the membrane structures is determined by dividing the complicated curved 3-D surface into several 2-D plane strip by using flattening technique. In this procedure, however, some discrepancies ore occurred between actual stresses of equilibrated state and designed uniform stresses because the material properties are not considered. These deviations can cause the critical structural problems, wrinkling or overstress, and thus a optimization process should be considered. In this paper, a new analytical method for determining an optimum cutting pattern considering material properties is presented. Here, iterative procedure is introduced to decrease the errors caused in numerical process. The optimization method proposed can diminish the deviations occurred by material properties and numerical errors, simultaneously. As a results, it is shown that the final stress distributions for the HP shell model are sufficiently near to design stress distributions, and it can be concluded that this method can be used to obtain the optimized cutting pattern of membrane structures.
Generally, truss design has been determined by the designer's experience and intuition. But if we perform the most economical structural design we must consider not only cross-sections of members but also configurations(howe, warren and pratt types etc.) of single truss as the number of panel and truss height. The purpose of this study is to develope automated optimum design techniques for steel truss structures considering cross-sections of members and shape of trusses simultaneously. As the results, it could be possible to find easily the optimum solutions subject to design conditions at the preliminary structural design stage of the steel truss structures. In this study, the objective function is expressed as the whole member weight of trusses, and the applied constraints are as stresses, slenderness ratio, local buckling, deflection, member cross-sectional dimensions and truss height etc. The automated optimum design algorithm of this study is divided into three-level procedures. The first level on member cross-sectional optimization is performed by the sequential unconstrained minimization technique(SUMT) using dynamic programming method. And the second level about truss height optimization is applied for obtaining the optimum truss height by three-equal interval search method. The last level of optimization is applied for obtaining the optimum panel number of truss by integer programming method. The algorithm of multi-level optimization programming technique proposed in this study is more helpful for the economical design of plane trusses as well as space trusses.