A connection between pulse-periodical laser radiation power and stability of liquid-metal contacts between powder particles during selective laser sintering (SLS) is determined based on analysis solving the problem of stability of liquid column in the gravity and capillary forces field. On the grounds of obtained relationships the optimization of pulse-periodical laser radiation power and SLS-process duration is realized, that allows to produce voluminous powder porous materials with pre-determined physical and mechanical properties and surface geometry. Results of metallographic investigations of powder porous materials of titanium powder produced with technological regimes calculated by means of obtained relationships are given in the work

Magnetic oxide-coated iron nanoparticles with the mean size ranging from 6 to 75 nm were synthesized by aerosol method using iron carbonyl as a precursor under the flowing inert gas atmosphere. Oxide shells were formed by passivation of asprepared iron particles. The influence of experimental parameters on the nanoparticles' microstructure, phase composition and growth behavior as well as magnetic properties were investigated and discussed in this study.

The free sintering of metallic powders blended with non sintering inclusions is investigated by the Discrete Element Method (DEM). Each particle, whatever its nature (metallic or inclusion) is modeled as a sphere that interacts with its neighbors. We investigate the retarding effect of the inclusions on the sintering kinetics. Also, we present a simple coarsening model for the metallic particles, which allows large particles to grow at the expense of the smallest.

Metal/diamond binary composite coatings on Al substrate without grit blasting were deposited by cold spray process with insitu powder preheating. Microstructural characterization of the as-sprayed coatings with different diamond size, strength and with/without Ti coating on diamond was carried out by OM and SEM. The assessment of basic properties such as tensile bond strength and hardness of the coatings, and the deposition efficiency was also carried out. Particular attention on the composite coatings was on the diamond fracture phenomenon during the cold spray deposition and the interface bonding between the diamond and the Fe-based metal matrix.

This paper describes a Plasma Assisted Debinding and Sintering (PADS) equipment, which has been designed to process Metal Injection Molded (MIM) components. The use of a hybrid system combining a glow discharge with a conventional heating system makes debinding and sintering of MIM components, in the same heating cycle, a feasible industrial process. Characteristics as density, carbon content and mechanical properties are similar to traditionally processed MIM materials. The reduction of energy and gas consumption and shorter lead-times are economic advantages of PADS system. The clean environment of PADS is also an ecological advantage.

Cylindrical specimens with different levels of density have been submitted to uniaxial compression tests with loading and unloading cycles. The analysis of the elastic loadings shows a non linear elasticity which can be mathematically represented by means of a potential law. Results are explained by assuming that the total elastic strain is the contribution of two terms one deriving from the hertzian deformation of the contacts among particles and another that takes into account the linear elastic deformation of the powder skeleton. A simple model based in an one pore unit cell is presented to support the mathematical model.

The results of monotonic and cyclic uniaxial compression tests, in which the deviatoric component of the stress is predominant, carried out on green and recrystallized iron compacts with different levels of density are presented and discussed in order to analyse the macro and micro-mechanisms governing the mechanical behaviour of non-sintered PM materials. The plastic deformation of the particles, especially at the contact areas between neighbouring grains, produces an internal friction responsible for the main features observed in the behaviour of green metallic compacts. These results show important discrepancies with the plasticity models, Cam-Clay and Drucker-Prager Cap.

The use of hot gas in melt atomization has been widely reported, but little detailed experimental data on its precise effects and no satisfactory theory to explain them have been published. In this paper the authors present experimental data on the atomization of metals with gas at temperatures from ambient to 1000C, a semi-empirical equation relating particle size to gas temperature and flow rate, and an analysis of the gas dynamics of the atomization process that allows some insight into the process.

The Solar Radio Burst Locator (SRBL) is a spectrometer that can observe solar microwave bursts over a wide band (0.1-18 GHz) as well as detect the burst locations without interferometry or mechanical scanning. Its prototype has been operated at Owens Valley Radio Observatory (OVRO) since 1998. In this study, we have evaluated the capability of the SRBL system in flux and radio burst location measurements. For this, we consider 130 microwave bursts from 2000 to 2002. The SRBL radio fluxes of 53 events were compared with the fluxes from USAF/RSTN and the burst locations of 25 events were compared with the optical flare locations. From this study, we found: (1) there is a relatively good correlation (r = 0.9) between SRBL flux and RSTN flux; (2) the mean location error is about 8.4 arcmin and the location error (4.7 arcmin) of single source events is much smaller than that (14.9 arcmin) of multiple source events; (3) the minimum location error usually occurred just after the starting time of burst, mostly within 10 seconds; (4) there is a possible anti-correlation (r = -0.4) between the pointing error of SRBL antenna and the location error. The anti-correlation becomes more evident (r=-0.9) for 6 strong single source events associated with X-class flares. Our results show that the flux measurement of SRBL is consistent with that of RSTN, and the mean location error of SRBL is estimated to be about 5 arcmin for single source events.

The inhibition of cell recovery might be proceeded via either the damage of the mechanism of the recovery itself or via the formation of irreversible damage which could not be repaired at all. Both these processes may take place at the same time. Any of t

실험실 조건에서 고구마 뒷날개흰밤나방의 교미 전 행동습성을 관찰하였다. 짝이 있고 어두운 상태에서 안테나를 치켜세우고 날개를 진동하는 습성을 보였으며, 암컷과 수컷 모두 날개를 진동하고 안테나를 치켜세우는 행동을 보이다가 수컷이 암컷에게로 날아가는 습성을 보였다. 불이 꺼진상태로 20여분이 지나면 안테나를 치켜세우는 반응을 보이기 시작하였으며 40분이 지났을 때부터 마치 짝을 유인하는 음향을 생성하듯이 날개를 빠르게 진동하는 반응을 보였다. 짝짓기는 우화 후 이튿날부터 관찰되었으며 대부분 4일에서 6일 사이에 짝짓기를 하였다. 짝짓기는 평균 207분 동안 지속되었고, 대부분 3회까지 반복적으로 교미를 하였다. 관찰결과를 종합적으로 분석해보면 암컷이 신호를 보내고 수컷이 이에 반응하는 것으로 보이며, 암컷이 내는 음향이 뒷날개흰밤나방의 교미전 행동습성에 관련되어 있을 가능성이 높은 것으로 판단되었다.

This study was carried out to evaluate the effects of washing medium, breed and washing temperature of fresh and frozen-thawed boar sperm on mitochondrial activity and membrane integrity by flow cytometry. More than 80% of fresh sperm washed with mTLP-PVA medium at 20℃ exhibited an intact membrane and a functional mitochondrion. With frozen-thawed samples, a large number of sperm showed both damaged membrane (36.4~46.9%) and nonfunctional mitochondrion (55.1~71.1%) in the mTLP-PVA and BTS washing media at 20℃. There were no breed effects of fresh and frozen-thawed sperm on mitochondrial activity and membrane integrity. The percentages of damaged membrane of fresh and frozen sperm, respectively, were higher at 4℃ washing temperature than at 20℃ washing temperature in the mTLP-PVA medium. We found that washing medium and washing temperature of fresh and frozen-thawed boar sperm were important for the analyses of mitochondrial activity and membrane integrity by flow cytometry.

Porcine oviduct epithelial cells (POEC) are widely used in co-culture experiments to improve early embryonic development, in vitro fertilization in embryo transfer programs for domestic animals and in vitro maturation of immature germ cells. POEC were mechanically isolated and cultured in tissue culture medium 199. Cells grew continuously, and confluent monolayers were formed after 7 days. After forming confluent monolayer of epithelial cells, supernatant was collected as the condition medium for maturing round spermatids in vitro. Round spermatids were also separated mechanically and cultured in the POEC condition medium. In this study we observed that 20% of round spermatid cultured were matured into elongating spermatid after 24 h, and about 10% of round spermatid cultured showed complete elongation (elongated spermatid) within 24~48 h of in vitro culture. No further development was observed within 50~72 h and transformed cells lost their viability after 72 h. These preliminary findings suggest that the condition medium from POEC may be possible to overcome the round spermatid block by improving the milieu of culture system.