Alpha activities can be used for categorization, transportation, and disposal of radioactive waste generated from the operation of nuclear facilities including nuclear power plants. In order to transport and dispose of such low- and intermediate-level radioactive waste (LILW) to the Wolsong LILW Disposal Center (WLDC) at Gyeongju, the gross alpha concentration of an individual drum should be determined according to the acceptance criteria. In addition, when the gross alpha concentration exceeds 10 Bq/g, the inventory of the comprising alpha emitters in the waste is to be identified. Gross alpha measurements using a proportional counter are usually straightforward, inexpensive, and high-throughput, so they are broadly used to assay the total alpha activity for environmental, health physics, and emergency-response assessments. However, several factors are thoughtfully considered to obtain a reliable approximate for the entire alpha emitters in a sample, which include the alpha particle energy of a particular radionuclide, the radionuclide that is used as a calibration standard, the uniformity of film in a planchet, time between sample collection and sample preparation, and time between sample preparation and counting. Korea Atomic Energy Research Institute (KAERI) have evaluated the inventory of radionuclides in low-level radioactive waste drums to send every year hundreds of them to the WLDC. In this presentation, we revisit the gross alpha measurement results of the drums transported to WLDC in the past few years and compare them with the concentrations of alpha emitters measured from alpha spectrometry and gamma spectrometry. This study offers an insight into the gross alpha measurement for radioactive waste regarding calibration source, self-absorption effect, composition of alpha emitters, etc.

To achieve permanent disposal of radioactive waste drums, the radionuclides analysis process is essential. A variety of waste types are generated through the operation of nuclear facilities, with dry active waste (DAW) being the most abundant. To perform radionuclides analysis, sample pretreatment technology is required to transform solid samples into solutions. In this study, we developed a dry ashing-microwave digestion method and secured the reliability of the analysis results through a validity evaluation. Additionally, we conducted a comparative analysis of the radioactivity of 94Nb nuclides with and without the chemical separation process, which reduced the minimum detectable activity (MDA) level by more than 65-fold for a certain sample.

The nuclear fuel that melted during the Fukushima nuclear accident in 2011 is still being cooled by water. In this process, contaminated water containing radioactive substances such as cesium and strontium is generated. The total amount of radioactive pollutants released by the natural environment due to the nuclear accident in Fukushima in 2011 is estimated to be 900 PBq, of which 10 to 37 PBq for cesium. Radioactive cesium (137Cs) is a potassium analog that exists in the water in the form of cations with similar daytime behavior and a small hydration radius and is recognized as a radioactive nuclide that has the greatest impact on the environment due to its long half-life (about 30 years), high solubility and diffusion coefficient, and gamma-ray emission. In this study, alginate beads were designed using Prussian blue, known as a material that selectively adsorbs cesium for removal and detection of cesium. To confirm the adsorption performance of the produced Prussian blue, immersion experiments were conducted using Cs standard solution, and MCNP simulations were performed by modeling 1L reservoir to conduct experiments using radioactive Cs in the future. An adsorption experiment was conducted with water containing standard cesium solution using alginate beads impregnated with Prussian blue. The adsorption experiment tested how much cesium of the same concentration was adsorbed over time. As a result, it was found that Prussian blue beads removed about 80% of cesium within 10-15 minutes. In addition, MCNP simulation was performed using a 1 L reservoir and a 3inch NaI detector to optimize the amount of Prussian blue. The results of comparing the efficiency according to the Prussian volume was shown. It showed that our designed system holds great promise for the cleanup and detection of radioactive cesium contaminated seawater around nuclear plants and/or after nuclear accidents. Thus, this work is expected to provide insights into the fundamental MCNP simulation based optimization of Prussian blue for cesium removal and this work based MCNP simulation will pave the way for various practical applications.

If radioactive plumes are released outside due to loss of containment building integrity during a nuclear power plant accident, these materials might travel with the wind, affecting both the surrounding environment and neighboring countries. In China, most nuclear power plants are located on the eastern coast. Consequently, a radioactive plume generated during an accident could negatively impact even the western part of the Korean Peninsula due to westerly winds. To detect such problems early, respond quickly, and protect residents, a system that can monitor aerial radiation under normal conditions is needed. Additionally, a detection system that can operate in real-time in an emergencies conditions is required. The current method for aerial radiation measurement takes environmental radiation data from a monitoring post 1.5 m above the ground and converts it to altitude. To measure actual aerial radiation, an expansive area is surveyed by aircraft. However, this approach is both time-consuming and expensive. Thus, to monitor radioactive plumes influenced by environmental factors like wind, we need a radiation detector that can gauge both radioactivity and directionality. In this study, we developed a radiation detector capable of assessing both the radioactivity and directionality of a radioactive plume and conducted its performance evaluation. We miniaturized the radiation detector using a CZT (Cadmium Zinc Telluride) sensor, enabling its mounting on unmanned aerial vehicles like drones. It is configured with multi-channels to measure directionality of a radioactive plumes. For performance evaluation, we positioned two-channel CZT sensors at 90 degrees and measured the energy spectrum for angle and distance using a disk-type radioactive isotope. Using this method, we compared and analyzed the directionality performance of the multi-channel radiation detector. We also confirmed its capability to discern specific radioactivity information and nuclide types in actual radioactive plumes. Our future research direction involves mounting the multi-channel radiation detector on a drone. We aim to gather actual aerial radiation data from sensors positioned in various directions.

The nuclear power plant (NPP) decommissioning market is expected to expand not only domestically but also overseas. Proven technologies must be applied to decommission NPP. This is based on Article 41-2, Paragraph 2 of the domestic ‘Enforcement Decree Of The Nuclear Safety Act’. Proven technology refers to technology that has verified that it can be applied in the field through demonstration. In other words, in order to carry out NPP decommissioning, verification must be done. Demonstration refers to reducing technological uncertainty and directly verifying services implemented in the field. From a technology commercialization perspective, demonstration requires an approach based on technology readiness level (TRL) from a technology perspective and market readiness level (MRL) from a market perspective. The characteristics of demonstration also differ depending on the characteristics of each field. The demonstration in the field of nuclear energy is the demonstration of demand matching. This is to confirm the feasibility of the technology in the company’s required environment. In order to perform demonstration, a scenario must be derived by reflecting demonstration design considerations. After evaluating the derived scenario, an actual assessment is conducted using lab-based demonstration/virtual environment demonstration/real environment demonstration. What must be preceded by an actual assessment is confirming the consumer’s requirements. In this study, the necessary environment and requirements of consumer’s to perform NPP decommissioning were reviewed. The domestic decommissioning procedure requirements management system presents decommissioning procedures, potential worker accidents, and worker requirements. In the case of foreign countries, it was confirmed that complex wide need, cost benefit, risk reduction, waste generation, operation, reliability and maintenance (RAM) improvement and quantitative measures were evaluated for the technology to be demonstrated. Also the requirements for demonstrating decommissioning need to a detailed review of actual decommissioning cases. Therefore, a comparison must be made between the requirements based on actual NPP decommissioning cases and the requirements derived from this research process. Afterwards, the empirical research approach proposed by the Ministry of Trade, Industry and Energy was applied. The empirical research approach proposed by the Ministry of Trade, Industry and Energy is to secure a track record over a certain period of time and performance under conditions similar to the actual environment in the final research stage at the TRL level 6 to 8. Through this, it will be possible to confirm the suitability of overseas technology for domestic application.

KHNP is conducting research to decommission Wolsong Unit 1 Calandria. Establishment of preparation and dismantlement processes, conceptual design of equipment and temporary radiation protection facilities, and waste management are being established. In particular, the ALARA plan is to be established by performing exposure dose evaluation for workers. This study aims to deal with the methodology of evaluating exposure dose based on the calandria dismantling process. The preparation process consists of bringing in and installing tooling and devices, and removing interference facilities to secure work space. The main source term for the preparation process is the calandria structure itself and crud of feeders. In the case of the dismantlement process, a structure with a shape that changes according to the process was modeled as a radiation source. It is intended to estimate the exposure dose by selecting the number of workers, time, and location required for each process in the radiation field evaluated according to the preparation and dismantlement process. In addition, it is also conducting an evaluation of the impact on dust generated by cutting operations and the human impact of C-14, H-3, which are specialized nuclides for heavy water reactors. KHNP is conducting an exposure dose evaluation based on a process based on the preparation and dismantlement process for decommissioning Calandria through computation code analysis. If additional worker protection measures are deemed necessary through dose evaluation according to this methodology, the process is improved to prepare for the dismantling of worker safety priorities.

The thermal treatment of radioactive waste attracts great attention. The thermal treatment offers lots of advantages, such as significant volume reduction, hazard reduction, increase of disposal safety, etc. There are various thermal technologies to waste. The developed technologies are calcination, incineration, melting, molten salt oxidation, plasma, pyrolysis, synroc, vitrification, etc. The off-gas treatment system is widely applied in the technologies to increase the safety and operation efficiency. The thermal treatment generates various by-product and pollutants during the process. The dust or fly ash are generated as a particulate from almost every radioactive waste. The treatment of PVC related components generates hydrogen chloride, which usually brings corrosion of facility. The treatment of rubber and spent resin generates sulfur oxide, SOx. The treatment of nitrile rubber generates nitrogen oxide, NOx. The incomplete combustion of radioactive waste usually generates carbon oxide, COx. The process temperature also affects the generation of off gas, such as NOx and/or COx. Various off gas treatment components are organized for the proper treatment of the previously mentioned materials. In this study systematical review on off gas treatment will be reported. Also, worldwide experiences and developed facility will be reported.

The primary purpose of high temperature process of radioactive waste is to satisfy the waste acceptance criteria and volume reduction. The WAC offers the guideline of waste form fabrication process. The WAC is defined as quantitative or qualitative criteria specified by the regulatory body, or specified by and operator and approved by the regulatory body, for radioactive waste to be accepted by the operator of a repository for disposal, or by the operator of a storage facility for storage. The main objective of WAC is to protect staff and general public and environment by the containment of radioactive material, limit external radiation level, and prevent criticality. The WAC also offers systematic management of radioactive waste by standardization of waste management operations, facilitation waste tracking, ensure safe and effective operation of operating facilities, etc. Since the high temperature process for radioactive waste is considered in many countries, lots of codes and standards are considered. In many WACs, compressive strength, thermal cycle stability, radiation exposure stability, free liquid, and leachability are evaluation to understand the effect of solidified form to the disposal facility. In this paper, systematical review on waste form will be discussed. In addition, brief result of characterization of waste form will be compared.

Thermal cutting processes that can be applied to dismantling nuclear power plants include oxygen cutting, plasma cutting, and laser cutting. According to the global trend, research projects are being carried out in various countries to upgrade laser cutting, and many studies are also being conducted in Korea with plans to apply laser cutting processes when dismantling nuclear power plants. However, with the current technology level of the laser cutting process, the maximum thickness that can be cut is limited to 250 mm. Therefore, in this study, a laser-oxygen hybrid cutting process was implemented by adding a laser heat source to the oxygen cutting process that can cut carbon steel with a thickness of 250 mm or more (RV, beam, column, beam, etc.) when dismantling the nuclear power plant. This has the advantage of improving the cutting speed and reducing the cutting width Kerf compared to conventional oxygen cutting. In this research, the laser-oxygen hybrid cutting process consisted of laser cutting to which Raycus’ 8 kW Fiber Laser power source was applied and oxygen cutting to which hydrogen was applied with Fuel Gas. The oxygen torch was placed perpendicular to the test piece, and the laser head was irradiated by tilting 35° to 70°. The effects of cutting directions on quality and performance were studied, and cutting paths were selected by comparing cutting results. Thereafter, it was confirmed that there is an optimal laser output power according to the cutting thickness by studying the effect on the cutting surface quality by changing only the laser output power under the same cutting conditions. The results of this study are expected to be helpful in the remote cutting process using laser-oxygen hybrid cutting when dismantling domestic nuclear power plants in the future.

As the decommissioning of domestic nuclear power plants (Gori Unit 1 and Wolseong Unit 1) becomes more visible, many research projects are being conducted to safely and economically decommissioning of domestic nuclear power plants (NPPs). After permanent shutdown, decommissioning of NNPs proceeds through decontamination, cutting of main equipment, waste disposal and site restoration stages. And various technologies are applied at each stage. In particular, remote cutting of neutron induced structures (RV, RVI, etc.) is a technology used in developed countries in the cutting stage, and remote cutting has been evaluated as a core technology for minimizing workers’ radiation exposure. Generally, remote cutting technologies are divided into mechanical/thermal/electrical cutting. Among various thermal cutting technologies, plasma arc cutting (PAC) is more economical and easily to remote control than other cutting technologies, and is also effective in cutting STS304 plates. PAC is a thermal cutting technology that melts the base material at the cutting area with a plasma arc heat source and removes melted material by blowing it out with cutting gas. The cutting quality depends on the stand-off distance and power (current), material thickness, cutting speed, etc., while double arcing will occur if the cutting conditions are not suitable. A monitoring system that can confirm double arcing during remote cutting is necessary because double arcing can reduce cutting quality, increase secondary waste (increase kerf and aerosol), and cause non-cutting. In this study, we used an ultrahigh-speed camera equipped with a band-pass filter to capture clear arc shapes, and measured voltage waveforms with a data acquisition system. We studied a monitoring method that can confirm the occurrence of double arcing by synchronizing the obtained arc shape and voltage waveform, and the effects of double arcing on the STS304 plates. The results of this study are expected to be helpful in the development of the remote cutting process using plasma arc cutting when decommissioning of domestic NPPs.

The domestic Pressurized Heavy Water Reactor (PWHR) nuclear power plant, Wolsong Unit 1, was permanently shut down on December 24, 2019. However, research on decommissioning has mainly focused on Pressurized Water Reactors (PWRs), with a notable absence of both domestic and international experience in the decommissioning of PHWRs. If proper business management such as radiation safety and waste is not performed, it can lead to increased business risks and costs in decommissioning. Therefore, the assessment of waste volume and cost, which provide fundamental data for the nuclear decommissioning process, is a crucial technical requirement before initiating the actual decommissioning of Wolsong Unit 1. Decommissioning radiation-contaminated structures and facilities presents significant challenges due to high radiation levels, making it difficult for workers to access these areas. Therefore, technology development should precede decommissioning process assessments and safety evaluations, facilitating the derivation of optimal decommissioning procedures and ensuring worker safety while enhancing the efficiency of decommissioning operations. In this study, we have developed a program to estimate decommissioning waste amounts for PHWRs, building upon prior research on PWR decommissioning projects while accounting for the specific design characteristics of PHWRs. To evaluate the amount of radioactive waste generated during decommissioning, we considered the characteristics of radioactive waste, disposal methods, packaging container specifications, and the criteria for the transfer of radioactive waste to disposal operators. Based on the derived algorithm, we conducted a detailed design and implemented the program. The proposed program is based on 3D modeling of the decommissioning components and the calculation of the Work Difficulty Factor (WDF), which is used to determine the time weighting factors for each task. Program users can select the cutting and packaging conditions for decommissioning components, estimate waste amount based on the chosen decommissioning method, and calculate costs using time weighting factors. It can be applied not only to PHWRs, but also to PWRs and non-nuclear fields, providing a flexible tool for optimizing decommissioning process.

After the major radioactivation structures (RPV, Core, SG, etc.) due to neutron irradiation from the nuclear fuel in the reactor are permanently shut down, numerous nuclides that emit alpha-rays, beta-rays, gamma-rays, etc. exist within the radioactive structures. In this study, nuclides were selected to evaluate the source term for worker exposure management (external exposure) at the time of decommissioning. The selection of nuclides was derived by sequentially considering the four steps. In the first stage, the classification of isotopes of major nuclides generated from the radiation of fission products, neutron-radiated products, coolant-induced corrosion products, and other impurities was considered as a step to select evaluation nuclides in major primary system structures. As a second step, in order to select the major radionuclides to be considered at the time of decommissioning, it is necessary to select the nuclides considering their half-life. Considering this, nuclides that were less than 5 years after permanent suspension were excluded. As a third step, since the purpose of reducing worker exposure during decommissioning is significant, nuclides that emit gamma rays when decaying were selected. As a final step, it is a material made by radiation from the fuel rod of the reactor and is often a fission product found in the event of a Severe accident at a nuclear power plant, and is excluded from the nuclide for evaluation at the time of decommissioning is excluded. The final selected Co-60 is a nuclide that emits high-energy gamma rays and was classified as a major nuclide that affects the reduction of radiation exposure to decommissioning workers. In the future, based on the nuclide selection results derived from this study, we plan to study the evaluation of worker radiation exposure from crud to decommissioning workers by deriving evaluation results of crud and radioactive source terms within the reactor core.

The Wolsong unit 1 decommissioning project is the world’s first commercial pressurized heavy water reactor decommissioning project. Although there is a lot of accumulated experience and technology for decommissioning of pressurized water reactors around the world, it can be said that there is great difficulty as there is lack of prior experience and reference materials for pressurized heavy water reactor. On the other hand, if the world’s first pressurized heavy water reactor project is completed, it is possible to enter the overseas market for pressurized heavy water reactor decommissioning. It is also a good opportunity to do so. Accordingly, the current status of operation, plans, and construction of infrastructure related to decommissioning of pressurized heavy water reactors in Canada, which can be said to be the home country of pressurized heavy water reactor, were reviewed. So, this study seeks to present considerations for entering the pressurized heavy water reactors decommissioning market in the future.

Wolsong Unit 1 nuclear power plant, which was permanently shut down in 2019, has a 678 MWe calandria vessel of the CANDU-6 type pressurized heavy-water reactor model. The calandria inside the vault is a horizontal cylindrical vessel made of stainless steel with a length of 7.8 m and a thickness of 28.6 mm. For the entire dismantling processes of a nuclear power plant, dismantling works cannot be performed using only one cutting technology and method, and when performing dismantling of a calandria vessel, various systems and components can be used for cutting and dismantling. The calandria vessel is located in a concrete compartment called a vault, and in order to safely dismantle the calandria vessel, the spread of radioactive contaminants from inside of the vault to the outside must be prevented. We designed dismantling processes using the laser cutting method to dismantle the calandria vessel and end shields. We must minimize the risk of internal radiation exposure to workers from aerosols derived from the thermal cutting processes. Therefore, we need a way to prevent secondary contamination from spreading outside the vault and within the reactor building. The path through which radioactive contaminants move is that the flying airborne products generated during the cutting process inside the vault where the calandria is located do not stay in place but spread outward through the opening of the RM-Deck structure at the top. Therefore, facilities or devices are needed to effectively prevent the spread of radioactive contaminants by blocking the expected movement path. By using these facilities or devices, it is possible to prevent the movement of radioactive aerosol particles between the location of the worker and the location of the cutting area where the calandria is located, thereby preventing internal exposure through the worker’s breathing. In addition, by using these, the cutting area where airborne pollutants are generated can be designed as an isolated work space to prevent the spread of radioactive contaminants. In this study, we propose a method of facilities for confining radioactive aerosol particles and preventing the spread of contamination when thermal cutting of the calandria vessel within the vault.

The radiation field generated in the primary cooling system of a nuclear power plant tends to increase in intensity as radionuclides bind to the oxide film on the internal surface of the primary system, which is operated at high temperature and pressure, and as the number of years of operation increases. Therefore, decontamination of the primary cooling system to reduce worker exposure and prevent the spread of contamination during maintenance and decommissioning of nuclear power plants uses the principle of simultaneous elution of radionuclides when the corrosion oxide film dissolves. In general, a multi-stage chemical decontamination process is applied, taking into account the spinel structure of the corrosion oxide film formed on the surface of the primary cooling system, i.e. an oxidative decontamination step is applied first, followed by a reductive decontamination step, which is repeated several times to reach the desired decontamination goal. Currently, permanganic acid is commonly used in oxidative decontamination processes to remove Cr from corrosion oxide films. In the reductive decontamination step to remove iron and nickel, organic acids such as oxalic acid are commonly used. However, organic acids are not suitable for the final radioactive waste form. A number of multi-stage chemical decontamination technologies for primary cooling systems have been developed and commercialized, including NP-CITROX, AP/NP-CANDECON, CANDERM, AP/NP-LOMI and HP/CORD-UV. Among these, HP/CORDUV is currently the most actively applied primary cooling system chemical desalination process in the world. In this study, KAERI has developed a new chemical decontamination technology that does not contain organic chemical decontamination agents, with a focus on securing an original technology for reducing the amount of decontamination waste while having equivalent or better decontamination performance than overseas commercial technologies, and compared it with the inorganic chemical agent-based HyBRID (Hydrazine Based Reductive Metal Ion Decontamination) chemical decontamination technology.

There are analytical methods used for measuring activity when light photons are emitted for scintillating-based analytical application. When this electron returns to the original stable state, it releases its energy in the form of light emission (visible light or ultraviolet light), and this phenomenon is called scintillation. Scintillator is a general term for substances that emit fluorescence when exposed to radiation such as gamma-rays. Radioactivity is all around us and is unavoidable because of the ubiquitous existence of background radiations emitted by different sources. The scintillator contributes to these sensing, and it is expected that the inspection accuracy and limit of detection will be improved and new inspection methods will be developed in the future. Moreover, scintillators are chemical or nanomaterial sensors that can be used to detect the presence of chemical species and elements or monitor physical parameters on the nanoscale. In this study, it includes finding use in scintillating-based analytical sensing applications. A chemical and nanomaterial based sensors are self-contained analytical tools that could provide information about the chemical compositions or elements of their environment, that is, a liquid or even gas condition. Herein, we present an insightful review of previously reported research in the development of high-performance gamma scintillators. The major performance-limiting factors of scintillation are summed up here. Moreover, the 2D material has been discussed in the context of these parameters. It will help in designing a prototype nanomaterial based scintillators for radiation detection of gamma-ray.

The type of radioactive waste that may occur in the process of nuclear power plant dismantling can be classified into solid, liquid, gas, and mixed waste. The amount of these wastes must be defined in the Final Decommissioning Plan for approval of the licensing. Also, in the case of Metal radioactive waste, it is necessary to calculate the generation amount in order to treat radioactive waste at a Radioactive Waste Treatment Facility (RWTF). Since a large quantity of metal radioactive waste is generated during the decommissioning of a nuclear power plant, the application of a metal melter for reduction is considered. The metal waste is heated to a temperature above the melting point and separated into liquid and gas forms. Nuclides existing on the surface of metal waste vaporize in a melting furnace to become dust or collect in sludge. Nonvolatile nuclides such as Co, Fe and Mn remain in ingot, but other nuclides can be captured and reduced with dust and sludge. And the types of melting furnaces to be applied can be broadly classified into Atmospheric Induction Melter (AIM) and Vacuum Induction Melter (VIM). Therefore, this review intends to compare the two types of metal furnaces to be included in RWTF.

As unit 1 of Kori was permanently shut down in June 2017, domestic nuclear industry has entered the path of decommissioning. The most important thing in decommissioning is cost reduction. And volume reduction of radioactive waste is especially important. According to the IAEA report, more than 4,000 tons of metallic waste is generated during the decommissioning of a 1,000 MWe reactor and most of these wastes are LLW or VLLW. To reduce amount of metallic waste dramatically, we should choose efficient decontamination method. In this study, we conducted dry ice and bead blasting decontamination. We prepared Inconel-600 and STS-304 specimen with dimensions of 30 mm × 30 mm × 5 mm. Loose and fixed contamination was applied on the surface of specimen using SIMCON method. Bead and dry-ice blasting was conducted by spraying alumina and dry ice pellet at the same pressure and distance for the same time. The removal of loose contamination was observed using microscope. It was found that contaminants are significantly removed using both dry ice blasting and bead blasting. However, some abrasive material remained on the surface of specimen. The removal of fixed contamination was verified by weight comparison before and after experiment and cobalt concentration comparison before and after experiment using X-ray Fluorescence Spectroscope (XRF). At least 90% of the cobalt was removed, but some abrasive particle was also remained on the surface of specimen. In this study, it is confirmed that the effectiveness of manufacturing a large-scale abrasive decontamination facility, and it is expected that this technology can be used to effectively reduce the amount of metallic waste generated during decommissioning.

Radioactive contamination distribution in nuclear facilities is typically measured and analyzed using radiation sensors. Since generally used detection sensors have relatively high efficiency, it is difficult to apply them to a high radiation field. Therefore, shielding/collimators and small size detectors are typically used. Nevertheless, problems of pulse accumulation and dead time still remain. This can cause measurement errors and distort the energy spectrum. In this study, this problem was confirmed through experiments, and signal pile-up and dead time correction studies were performed. A detection system combining a GAGG sensor and SiPM with a size of 10 mm × 10 mm × 10 mm was used, and GAGG radiation characteristics were evaluated for each radiation dose (0.001~57 mSv/h). As a result, efficiency increased as the dose increased, but the energy spectrum tended to shift to the left. At a radiation dose intensity of 400 Ci (14.8 TBq), a collimator was additionally installed, but efficiency decreased and the spectrum was distorted. It was analyzed that signal loss occurred when more than 1 million particles were incident on the detector. In this high-radioactivity area, quantitative analysis is likely to be difficult due to spectral distortion, and this needs to be supplemented through a correction algorithm. In recent research cases, the development of correction algorithms using MCNP and AI is being actively carried out around the world, and more than 98% of the signals have been corrected and the spectrum has been restored. Nevertheless, the artificial intelligence (AI) results were based on only 2-3 overlapping pulse data and did not consider the effect of noise, so they did not solve realistic problems. Additional research is needed. In the future, we plan to conduct signal correction research using ≈10×10 mm small size detectors (GAGG, CZT etc.). Also, the performance evaluation of the measurement/analysis system is intended to be performed in an environment similar to the high radiation field of an actual nuclear facility.

When aluminum is in an alkaline state, the aluminum oxide film surrounding aluminum is dissolved and moisture penetrates the exposed aluminum surface, causing corrosion of aluminum. At this time, hydrogen gas is generated and there is a risk of explosion due to the generated hydrogen gas. Aluminum radioactive waste is difficult to permanently dispose of because it does not meet the standards for the acquisition of low- and intermediate-level radioactive waste cave disposal facilities currently managed and operated by the Korea Nuclear Environment Corporation. However, because of this risk, it is necessary to study how to safely treat and dispose aluminum waste. In this study, overseas cases were investigated and analyzed to ensure the safety of aluminum waste disposal, and the current status of aluminum radioactive waste generated during decommissioning of the Korea Research Reactor 1&2 and a treatment plan to secure disposal suitability were presented. The process of removing a little remaining oxygen in molten steel during the reduction of iron oxide in the iron refining process is called deoxidation, and a representative material used for deoxidation is aluminum. In the case of metal melting decontamination, which is one of the decontamination processes of radioactive metal waste, a method of treating aluminum waste by using aluminum as a deoxidizer is proposed.