이 논문에서는 기존의 조인트 교량을 일체식 교대 교량으로 변경할 경우, 온도하중에 의한 상부구조의 인장에 따른 흉벽의 휨거동을 보강하기 위한 흉벽 FRP 보강공법을 제안하고, 설계 및 유한요소해석을 통해 보강 효과를 검토하였다. FRP 보 강재는 펄트루젼 공정으로 제작하며, 흉벽 전면부에 부착하여 일체식 교대 교량으로 변경할 때, 흉벽에 부족한 인장철근의 역할 을 대체하게 된다. 흉벽 FRP 보강공법의 설계는 ACI Committee 440을 참고하여 수행하였으며, 유한요소해석은 콘크리트, 철근 및 유리섬유와 비닐에스터로 제작한 FRP 보강재의 최대응력을 보강 방법에 따라 비교하였다. 유한요소해석 결과, FRP 보강재는 콘크리트에 발생하는 인장응력을 감소시키는 역할을 하며, 흉벽이 저항할 수 있는 휨모멘트를 증가시킬 수 있는 것으로 나타났 다.

이 논문에서는 교량받침 교체를 위한 에폭시 주입 공법을 제시하였다. 에폭시 주입 공법의 성능 평가를 위하여, 에 폭시 주입성 실험 및 통공앵커의 인발실험을 수행하였다. 에폭시 주입성 실험은 빈 공간을 갖고 있는 콘크리트 블록 내에 통공 앵커를 이용하여 에폭시를 주입하고, 콘크리트 블록을 절단한 후, 주입성능을 육안으로 관찰하였다. 또한, 인발실험은 2가지 형태의 통공앵커를 콘크리트 블록 내에 삽입하여 수행하였으며, 2가지 형태의 통공앵커에 대한 인발실험 결과를 비교하고, 케 미컬 앵커의 인발강도와도 비교하였다. 실험 결과 통공앵커는 교량받침 교체공사를 위한 에폭시 주입성과 인발성능이 우수한 것으로 나타났다.

In this study, we learned about the effects of indoor radon concentration reduction associated with the operation of a mechanical ventilation system at an apartment house. The experimental parameters were mainly the indoor radon level and air change rate, which were controlled by the amount of emissions released and fan motor speed. Even at the high level of radon diffused in an apartment house, indoor radon concentrations converged to the Korean national guideline level within 3 to 4 hours when the air was ventilated at 0.5 ACH and 0.7 ACH. In the case of 0.3 ACH, however, where the degree of ventilation was insufficient compared to the legal air change rate, the high concentration indoor radon could not be sufficiently removed even if the mechanical ventilation system was operated for more than 14 hours continuously. When the indoor radon level was high, the reduction rate was 34.3% for 0.3 ACH, 70.4% for 0.5 ACH, and 69.7% for 0.7 ACH at 6 hours-operation, while at the medium-level, indoor radon can be reduced by 46.2% (0.3 ACH) to 73.2% (0.7 ACH). Depending on the indoor concentration range, it may be required to secure a ventilation rate of 0.5 ACH or more at all times. In addition, in apartment houses with excellent airtight performance, even if indoor radon is at a level similar to the national guideline, it is difficult to expect a reduction in the concentration due to natural decay. Therefore, it is desirable to lower the indoor concentrations as much as possible.

This study was designed to verify what effect the use of a natural ventilation system can have on improving indoor air quality with regard to radon in various concentration ranges in an apartment house. The results show that both high (2~3 times higher than 148 m3) and low (similar to 148 Bq/m3) levels of indoor radon concentrations can be reduced close to and/or below the Korean IAQ guideline within 6 hours when the natural ventilation system is operated at approximately an air change rate of 0.5. In the case of an air change rate of 0.3, however, the indoor radon levels cannot meet the national guidelines and the reduction effect was insufficient with regard to various radon concentrations. Typically, the air change rate of a natural ventilation system is affected by meteorological factors such as temperature, relative humidity, wind speed, pressure. Its effectiveness varies according to such factors, for that reason, the reduction effects on radon did not increase proportionally with the ventilation time in this study.

본 연구는 자가간호프로그램이 요추간판제거술 환자의 운동이행 자기효능감, 자가간호지식, 자가간호이행에 미치는 효과를 확인하기 위한 실험연구이다. 대상자는 D광역시 소재 일개 척추전문병원 입원환자 중 미세현미경 요추간판제거술을 받은 환자로 실험군 26명, 대조군 27명이다. 수집된 자료는 SPSS 25프로그램을 이용하여 평균, 백분율, 표준편차, t-test, χ2-test, t-test, repeated measures ANOVA로 분석하였다. 연구결과 자가간호프로그램 중재를 받은 실험군은 제공받지 않은 대조군에 비해 시간이 경과함에 따라 보조기 관리지식(p=.001)과 일상생활관리지식점수(p=.005)가 더 높아 지지되었다. 또한 자가간호 프로그램을 제공받은 실험군은 제공받지 않는 대조군보다 보조기 관리이행도(p=.011), 일상생활 이행도 (p=.007), 유해생활 습관관리 이행도(p=.011)가 높아 지지되었다. 따라서 자가간호프로그램은 요추간판제 거술 환자의 수술 전후 적용을 통해 운동이행 자기효능감, 자가간호지식 및 자가간호이행도를 향상시켜 보다 빠른 회복을 도울 수 있는 프로그램이라고 할 수 있다.

혈관내큰B세포림프종은 악성 림프구의 혈관 내 성장을 보이는 드문 질환으로, 말초혈액 또는 혈관 외 종괴를 보이지 않는다. 이 림프종은 빠른 파종 및 공격적 성향 때문에 나쁜 예후를 가진다. 그러나 질병특유소견이 없어 진단이 어려운 실정이다. 저자들은 십이지장 위장관기질종양의 수술 검체 내에서 혈관내큰B세포림프종이 진단된 증례를 발견하였기에 문헌고찰과 함께 보고하는 바이다.

저자들은 십이지장의 팽대부에서 발견된 종양에 대해 조직검사를 시행, 신경내분비종으로 판단하여 내시경적 유두부 절제술을 시행하였으며 신경절세포 부신경절종으로 진단된 증례를 경험하였으며, 신경절세포 부신경절종이 내시경적 유두부절제술로 성공적으로 치료되었기에 문헌고찰과 더불어 보고하는 바이다.

다발체 형성과 인발 공정으로 제조된 Cu-Nb 필라멘트 미세복합재료의 기계적 전기적 특성에 대하여 연구하였다. Nb의 함량이 증가함에 따라 강도는 점차 증가하였으나 연성은 Nb의 함량에 무관하였다. 293K와 75K에서의 항복강도의 비율은 Cu-Nb 미세복합재료의 Young의 계수 비율과 비슷하게 관찰되었다. 이러한 사실은 주로 장범위 방해물(athermal obstacles)들이 Cu-Nb 마세복합재료의 강도에 영향을 미친다는 것을 의미한다. 파면 조직관찰 결과는 Cu-Nb 미세복합재료는 Nb의 함량에 판관계없이 연성파괴의 특성을 나타내었으며, 부전선재 (subelematal wires)사이의 계면을 따라 발생하는 2차크랙 (secondary crack) 의 양은 Nb 함량이 증가함에 따라 증가하였다. 전기 전도도와 비저항비 (ρ293k/rho75k)는 Nb 함량이 증가할수록 감소하였다. 이와 같은 Nb함량에 따른 전기전도도와 비저항비의 감소는 계면산란의 기여도가 증가하였기 때문이다.

In this research, heavy metals and T-P removal characteristics of plated wastewater are derived using BPC(Break Point Chlorination) process. AA sedimentation pond outflow(Influence) was evaluated for the removal efficiency of heavy metal(Ni) and T-P at a reaction time of 25 minutes by NaOCl input volume(9, 11, 13 and 15 mL). In the case, the higher the NaOCl input volumes, the higher the ORP values were maintained and the higher the removal efficiency tended to be. On the other hand, T-P was judged to have a low relationship between the ORP value and the removal efficiency. In addition, the efficiency of removal heavy metals and T-P in the plated wastewater by injecting 10 mL, 15 mL, 20 mL and 25 mL NaOCl, increased as the amount of NaOCl injected increased, the amount of NaOH input for pH increased. It was found that suspended solid in effluence also increased. It was also observed that the color of the plating wastewater changed from yellowish green to green to charcoal gray to black as the amount of NaOCl injected increased. Treatment characteristics of the reaction time, the longer the reaction time with the substance to be treated after the input of NaOCl, the more the heavy metal removal efficiency tended to increase. Through XRF analysis of the sludge, the constituents in the sludge such as NaCNO, CNCl, Na3PO4, CrO4, 2Na2CrO4 and 2NaNO3 will be analyzed in detail, and the mechanisms of the reaction between the plated wastewater and the complex compound will be elucidated.

Livestock manure treatments have become a more serious problem because massive environmental pollutions such as green and red tides caused by non-point pollution sources from livestock manures have emerged as a serious social issue. In addition, more food wastes are being produced due to population growth and increased income level. Since the London Convention has banned the ocean dumping of wastes, some other waste treatment methods for land disposal had to be developed and applied. At the same time, researches have been conducted to develop alternative energy sources from various types of wastes. As a result, anaerobic digestion as a waste treatment method has become an attractive solution. In this study has three objectives: first, to identify the physical properties of the mixture of livestock wastewater and food waste when combining food waste treatment with the conventional livestock manure treatment based on anaerobic mesophilic digestion; second, to find the ideal ratio of waste mixture that could maximize the collection efficiency of methane (CH4) from the anaerobic digestion process; and third, to promote CH4 production by comparing the biodegradability. As a result of comparing the reactors R1, R2, and R3, each containing a mixture of food waste and livestock manure at the ratio of 5:5, 7:3, and 3:7, respectively, R2 showed the optimum treatment efficiencies for the removal of Total Solids (TS) and Volatile Solids (VS), CH4 production, and biodegradability.

The aim in this study was to remove Cl−, which can be problematic in the recycling of bottom ash, by identifying the optimum operating conditions for a soil electrolysis apparatus with spiral paddles and to use these as the base data in removing contaminants from various polluted soils using electrolysis. Unprocessed bottom ash collected from the openair storage yard at thermoelectric power plant H in Gyeong sang nam - do Province was used as the experimental material. The experimental methodology was to identify the optimum operating conditions to remove Cl− contained in the bottom ash using the following variables: use or not of spiral paddles, application or not of electrolysis, change of concentration of the electrolyte solution, electrolysis application time, and the voltage level during electrolysis. From the results, the highest removal efficiency of 91.4% was shown under the following conditions: use of the spiral paddles, use of 0.3% NaOH electrolyte solution, 20 min of electrolysis; and a voltage level of 5 V during electrolysis. It is evident that application of the soil electrolysis apparatus for removal of Cl− from bottom ash could be valuableas base data for purification of polluted soils in the future.

In this study, the International Maritime Organization (IMO)’s guideline MEPC. 277 (64) was developed and evaluated for the removal efficiency of T-N in a SBR and MBR combined process. This combined process of resized equipment based on large capacity water treatment device for a protection of marine aquatic life. In this experiment, T-N concentration of influent and effluent was measured through with the artificial wastewater. The SBR reactor operation time was varied according to the C : N : P ratios so that different conditions for mixing and aeration period in mins (90 : 60, 80 : 40, 70 : 50) and two C: N: P ratios (10 : 5 : 3, 10 : 3 : 1) were used. During experiment in the reactor’s aeration and anoxic tank DO concentrations were 3 mg/L and 0.2 mg/L respectively. Furthermore, in the reactor MLSS concentration was 2000 mg/L and flowrate was 2 L/hr. Experiment results showed that C : N : P, 10 : 3 : 1 ratio with 90 mins mixing and 60 mins aeration maximized removal efficiency at 97.3% T-N as compared to other conditions. The application of the SBR and MBR combined process showed efficient results.

This study aimed to remove organic matter and heavy metals that could affect the recycling of soils contaminated by heavy metals, by means of electrolysis, carried out simultaneously with the leaching of the soil. To ensure better experimental equipment, a soil electrolysis apparatus, equipped with spiral paddles, was used to agitate the heavy-metal-contaminated soil effectively. The heavy-metal-contaminated soil was electrolyzed by varying the voltage to 5 V(Condition 1), 15 V(Condition 2), and 20 V(Condition 3), under the optimal operating conditions of the electrolysis apparatus, as determined through previous studies. The results showed that the pH of the electrolyte solution and the heavy-metal-contaminated soil, after electrolysis, tended to decrease with an increase in voltage. The highest removal efficiencies of TOC and CODCr were 18.8% and 29.1%, 38.8% and 4.2%, and 33.3% and 50.0%, under conditions 1, 2 and 3, respectively. Heavy metals such as Cd and As were not detected in this experiment. The removal efficiencies of Cu, Pb and Cr were 4.7%, 8.3% and 2.1%, respectively, under Condition 1, while they were 42.9%, 15.2% and 22.1%, respectively, under Condition 2, and 4.7%, 23.0%, and 24.9%, respectively, under Condition 3. These results suggest that varying the voltage with the soil electrolysis apparatus for removing contaminants for the recycling of heavy-metal-contaminated soil allows the selective removal of contaminants. Therefore, the results of this study can be valuable as basic data for future studies on soil remediation.

This study was aimed at determining the changes in heavy metal removal efficiency at different acid concentrations in a micro-nanobubble soil washing system and pickling process that is used to dispose of heavy metals. For this purpose, the initial and final heavy metal concentrations were measured to calculate the heavy metal removal efficiency 5, 10, 20, 30, 60, and 120 min into the experiment. Soil contaminated by heavy metals and extracted from 0~15 cm below the surface of a vehicle junkyard in the city of U was used in the experiment. The extracted soil was air-dried for 24 h, after which a No. 10 (2 mm) was used as a filter to remove large particles and other substances from the soil as well as to even out the samples. As for the operating conditions, the air inflow rate in the micro-nano bubble soil washing system was fixed at 2 L/min,; with the concentration of hydrogen peroxide being adjusted to 5%, 10%, or 15%. The treatment lasted 120 min. The results showed that when the concentration of hydrogen peroxide was 5%, the efficiency of Zn removal was 27.4%, whereas those of Ni and Pb were 28.7% and 22.8%, respectively. When the concentration of hydrogen peroxide was 10%, the efficiency of Zn removal was 38.7%, whereas those of Ni and Pb were 42.6% and 28.6%, respectively. When the concentration of hydrogen peroxide was 15%, the efficiency of Zn removal was 49.7%, whereas those of Ni and Pb were 57.1% and 42.6%, respectively. Therefore, the efficiency of removal of all three heavy metals was the highest when the hydrogen peroxide concentration was 15%.

Livestock manure treatments have become a more serious problem because massive environmental pollutions such as green and red tides caused by non-point pollution sources from livestock manures have emerged as a serious social issue. In addition, more food wastes are being produced due to population growth and increased income level. Since the London Convention has banned the ocean dumping of wastes, some other waste treatment methods for land disposal had to be developed and applied. At the same time, researches have been conducted to develop alternative energy sources from various types of wastes. As a result, anaerobic digestion as a waste treatment method has become an attractive solution. In this study has three objectives: first, to identify the physical properties of the mixture of livestock wastewater and food waste when combining food waste treatment with the conventional livestock manure treatment based on anaerobic mesophilic digestion; second, to find the ideal ratio of waste mixture that could maximize the collection efficiency of methane (CH4) from the anaerobic digestion process; and third, to promote CH4 production by comparing the biodegradability. As a result of comparing the reactors R1, R2, and R3, each containing a mixture of food waste and livestock manure at the ratio of 5:5, 7:3, and 3:7, respectively, R2 showed the optimum treatment efficiencies for the removal of Total Solids (TS) and Volatile Solids (VS), CH4 production, and biodegradability.