With South Korea increasingly focusing on nuclear energy, the management of spent nuclear fuel has attracted considerable attention in South Korea. This study established a novel procedure for selecting safety-relevant radionuclides for long-term safety assessments of a deep geological repository in South Korea. Statistical evaluations were performed to identify the design basis reference spent nuclear fuels and evaluate the source term for up to one million years. Safety-relevant radionuclides were determined based on the half-life criteria, the projected activities for the design basis reference spent nuclear fuel, and the annual limit of ingestion set by the Nuclear Safety and Security Commission Notification No. 2019-10 without considering their chemical and hydrogeological properties. The proposed process was used to select 56 radionuclides, comprising 27 fission and activation products and 29 actinide nuclides. This study explains first the determination of the design basis reference spent nuclear fuels, followed by a comprehensive discussion on the selection criteria and methodology for safety-relevant radionuclides.

프리지아 ‘Ruby Star’는 농촌진흥청 국립원예특작과학원 에서 보라색 홑꽃 ‘Avilla’와 흰색 반겹꽃 ‘Medeo’를 2012년 교배하여 얻은 종자로부터 2006년 향이 좋고 개화기가 빠른 적색 홑꽃 계통을 선발하여 품종으로 개발되었다. 2014년부 터 2017년까지 생육·개화 특성검정 및 육성계통평가회의 기 호도 평가를 거쳐 선발되었으며 2018년 직무육성품종심의회 를 통해 ‘Ruby Star’로 명명되어 2021년 신품종으로 등록되 었다. ‘Ruby Star’는 빨간색(RHS, R45A) 홑꽃인 절화용 프리 지아 품종으로 개화소요일수가 118.0일이며 초장이 120.5cm 로 대조품종 ‘Rapid Red’보다 약 28.7cm 더 길다. 주당 분 지수는 5.8개로 대조품종에 비해 수확량이 많고 첫번째 분지 의 길이가 32.0cm, 두께가 3.02mm로 절화 특성이 우수하 다. ‘Ruby Star’의 소화수 및 소화폭은 각각 14.8개, 6.3cm 로 소화수가 많은 중대형화이다. 절화수명은 약 8.4일이며 주 당 자구수는 3.8개, 평균 자구중은 2.9g이다. 전자코를 이용 한 PCA 분석 결과 PC1과 PC2의 설명력은 각각 97.9%, 1.8%로 전체 변이의 99.7%를 반영했으며 ‘Ruby Star’와 대 조품종 ‘Rapid Red’는 서로 다른 향기 패턴을 보였다. Radar plot 결과 총 6개의 MOS 센서에서 ‘Ruby Star’의 센서 반응 이 ‘Rapid Red’보다 강하게 나타나 ‘Ruby Star’의 향기가 더 강한 것으로 나타났다.

제충국(Tanacetum cineariaiaefolium), 데리스(Derris elliptica), 고삼(Sophora flavescens) 추출물은 다양한 해충을 방제하는데 사용되고 있다. 하지만, 국내에서 판매되고 있는 식물추춞물 자재는 유효성분의 표기가 없고, 살충농도와 살충시간에 대한 자료가 전무한 상황이다. 본 연구에서는 상 용화된 주요 식물추출물의 살충유효성분의 농도를 결정하고 복숭아혹진딧물에 대해 살충농도와 살충시간을 측정하였다. 식물추출물의 살충활성성분 인 pyrethrins, rotenone, matrine과 oxymatrine의 농도는 액체 크로마토그래피에서 표준물질을 활용하여 질량분석을 통해 측정하였다. 식물추출 물을 농도별로 희석하여 복숭아혹진딧물에 살포하여 살충력을 측정하였다. 표준화합물과 비교한 후 질량분석 및 결정했습니다. Myzus persicae에 대 한 lethal concentation과 lethal time을 조사했다. 살포 후 48시간 후 치사 농도(LC50)는 pyrethrins (20.4 ppm), roteone (34.1 ppm), matrine (29.6 ppm)였고, 100 ppm 살포한 LT50은 pyrethrins (13.4시간), rotenone (15.1시간), matrine (14.4시간)로 측정되었다. Kaplan-Meier 생존분 석 결과, 100 ppm에서 세 가지 식물 추출물의 LT50은 대조구인 화학 살충제인 Sulfoxaflor를 살포 처리구보다 유의하게 빨랐습니다. 본 결과는 복숭 아혹진딧물 방제를 위해 식물추출물의 제형화에 단일 또는 혼합 제제를 개발하는데 기준 살충농도와 살충시간을 제고하는데 의미가 있다.

Background: Largemouth bass (Micropterus salmoides) is introduced species that has caused aquatic ecology activity both in vitro and in vivo were investigated for the possibility of application of the bass extract as an alternative feed ingredient. Methods: The bass oil was extracted using a 1-L supercritical extractor, while the protein was extracted from 250 g of bass dry matter, which was dissolved in 1 mL of H2O at 50℃. Both oil and protein extracts were evaluated antioxidant activities and the level of DPPH radical scavenging assay and nitric oxide (NO) production assay with lipopolysaccharide response. Oral administration of 6.6 μL/g bass protein and 5.38 μL/g bass oil conducted for investigating serological and physiological effect. Results: DPPH radical scavenging showed similar radical scavenging ability of 50 μM of ascorbic acid at 200 μg of protein and 10% of oil treatment. NO concentration was diminished by the treatment of bass oil. Oral administration of both bass oil and proteins to mice showed that the body weight increase rate of the bass oil treated group was significantly reduced by 1.55 g compared to the other groups. The number of white blood cells (WBC) was increased by 4.52 k/μL in the bass protein-treated group and 4.44 k/μL in the bass oil-treated group compared to the control group. However, the serum IgG level did not show a significant difference between the bass extract-treated groups and the control group. Conclusions: These studies demonstrate that both bass oil and proteins extracted from the bass not only provide excellent effects of antioxidant and immune activity but can also be used as functional food supplements.

수국은 수국과(Hydrangeaceae) 수국속(Hydrangea)의 낙엽관목 식물로 크고 화려한 화형을 가져 절화, 분화 및 조 경수로 전세계적 인기가 있는 식물이다. 나무수국은 수국 (H. macrophylla)과 비교하여 삽목율이 낮은 것으로 알려져 있지만 나무수국의 묘목생산을 위한 삽목 연구 및 두 종간 삽목율 차이 원인 규명에 관한 연구는 미미하다. 본 연구는 IBA(Indol-3-butyric acid) 500mg·L-1 처리시 삽수의 침지 시간에 따른 삽목율 조사를 통해 적정 호르몬 처리 시간을 제 시하고 나무수국과 수국의 해부학적 구조 관찰을 통한 삽목율 차이 발생의 원인을 규명하고자 실시하였다. 나무수국의 적정 호르몬 처리 시간을 규명하기 위해 IBA 500mg·L-1을 무처 리, 30분, 2시간, 4시간 침지처리를 하였다. 종간 삽목율 차이 발생의 원인 규명을 위해 나무수국과 수국의 줄기 단면과 삽 목 후 시간 경과에 따른 발근을 해부학적으로 관찰하였다. 연 구의 결과 나무수국의 삽목시 IBA 500mg·L-1에 2시간 이상 침지처리가 다른 처리구와 비교하여 발근율이 높고 발생 뿌리 수가 가장 많았다. 또, 나무수국의 삽목율이 수국과 비교하여 낮은 것은 줄기의 세포 구조상 방사조직의 형태, 섬유세포의 밀도, 도관의 발달, 전분 함유 세포의 수 등에 차이가 관찰되 었고 이러한 세포 구조적 차이들의 영향으로 나무수국이 수국 보다 삽목 후 뿌리 조직 세포분열이 7일 늦게 시작되는 것이 확인되었다. 본 연구의 결과로 나무수국의 삽목 번식의 기초 자료로 활용되어 묘목 생산 효율 증대에 활용되길 바란다.

본 연구는 환경교육용 보드게임 개발에 관한 연구다. 이를 위해 문헌 고찰과 전문가 인터뷰를 실시하여 핵심 메커니즘과 용어를 도출하였다. 또한, 타당도와 신뢰도 검증을 위하여 델파이 조사를 진행하였다. 연구 결과 9개 항목에 대하여 합의가 이뤄졌으며, 이를 기반으로 ‘수풀로 메이커’ 프로토타입을 제작하고 플레이테스트 를 진행하였다. 그 결과, 환경에 대한 관심, 생태복원의 개념, 탄소 중립에 대한 이해를 보여, 연구의 초기 목 적을 달성한 것으로 나타났다. 본 연구로 인해 개발된‘수풀로 메이커’는 아동과 청소년의 환경교육 교재의 역할 뿐만 아니라, 환경에 대한 깊이 있는 이해를 견인하고, 더 나아가 실천양식 변화의 잠재성을 키우는 역 할에 기여할 수 있을 것으로 기대한다.

To achieve permanent disposal of radioactive waste drums, the radionuclides analysis process is essential. A variety of waste types are generated through the operation of nuclear facilities, with dry active waste (DAW) being the most abundant. To perform radionuclides analysis, sample pretreatment technology is required to transform solid samples into solutions. In this study, we developed a dry ashing-microwave digestion method and secured the reliability of the analysis results through a validity evaluation. Additionally, we conducted a comparative analysis of the radioactivity of 94Nb nuclides with and without the chemical separation process, which reduced the minimum detectable activity (MDA) level by more than 65-fold for a certain sample.

The nuclear fuel that melted during the Fukushima nuclear accident in 2011 is still being cooled by water. In this process, contaminated water containing radioactive substances such as cesium and strontium is generated. The total amount of radioactive pollutants released by the natural environment due to the nuclear accident in Fukushima in 2011 is estimated to be 900 PBq, of which 10 to 37 PBq for cesium. Radioactive cesium (137Cs) is a potassium analog that exists in the water in the form of cations with similar daytime behavior and a small hydration radius and is recognized as a radioactive nuclide that has the greatest impact on the environment due to its long half-life (about 30 years), high solubility and diffusion coefficient, and gamma-ray emission. In this study, alginate beads were designed using Prussian blue, known as a material that selectively adsorbs cesium for removal and detection of cesium. To confirm the adsorption performance of the produced Prussian blue, immersion experiments were conducted using Cs standard solution, and MCNP simulations were performed by modeling 1L reservoir to conduct experiments using radioactive Cs in the future. An adsorption experiment was conducted with water containing standard cesium solution using alginate beads impregnated with Prussian blue. The adsorption experiment tested how much cesium of the same concentration was adsorbed over time. As a result, it was found that Prussian blue beads removed about 80% of cesium within 10-15 minutes. In addition, MCNP simulation was performed using a 1 L reservoir and a 3inch NaI detector to optimize the amount of Prussian blue. The results of comparing the efficiency according to the Prussian volume was shown. It showed that our designed system holds great promise for the cleanup and detection of radioactive cesium contaminated seawater around nuclear plants and/or after nuclear accidents. Thus, this work is expected to provide insights into the fundamental MCNP simulation based optimization of Prussian blue for cesium removal and this work based MCNP simulation will pave the way for various practical applications.

There are analytical methods used for measuring activity when light photons are emitted for scintillating-based analytical application. When this electron returns to the original stable state, it releases its energy in the form of light emission (visible light or ultraviolet light), and this phenomenon is called scintillation. Scintillator is a general term for substances that emit fluorescence when exposed to radiation such as gamma-rays. Radioactivity is all around us and is unavoidable because of the ubiquitous existence of background radiations emitted by different sources. The scintillator contributes to these sensing, and it is expected that the inspection accuracy and limit of detection will be improved and new inspection methods will be developed in the future. Moreover, scintillators are chemical or nanomaterial sensors that can be used to detect the presence of chemical species and elements or monitor physical parameters on the nanoscale. In this study, it includes finding use in scintillating-based analytical sensing applications. A chemical and nanomaterial based sensors are self-contained analytical tools that could provide information about the chemical compositions or elements of their environment, that is, a liquid or even gas condition. Herein, we present an insightful review of previously reported research in the development of high-performance gamma scintillators. The major performance-limiting factors of scintillation are summed up here. Moreover, the 2D material has been discussed in the context of these parameters. It will help in designing a prototype nanomaterial based scintillators for radiation detection of gamma-ray.

Radioactive contamination distribution in nuclear facilities is typically measured and analyzed using radiation sensors. Since generally used detection sensors have relatively high efficiency, it is difficult to apply them to a high radiation field. Therefore, shielding/collimators and small size detectors are typically used. Nevertheless, problems of pulse accumulation and dead time still remain. This can cause measurement errors and distort the energy spectrum. In this study, this problem was confirmed through experiments, and signal pile-up and dead time correction studies were performed. A detection system combining a GAGG sensor and SiPM with a size of 10 mm × 10 mm × 10 mm was used, and GAGG radiation characteristics were evaluated for each radiation dose (0.001~57 mSv/h). As a result, efficiency increased as the dose increased, but the energy spectrum tended to shift to the left. At a radiation dose intensity of 400 Ci (14.8 TBq), a collimator was additionally installed, but efficiency decreased and the spectrum was distorted. It was analyzed that signal loss occurred when more than 1 million particles were incident on the detector. In this high-radioactivity area, quantitative analysis is likely to be difficult due to spectral distortion, and this needs to be supplemented through a correction algorithm. In recent research cases, the development of correction algorithms using MCNP and AI is being actively carried out around the world, and more than 98% of the signals have been corrected and the spectrum has been restored. Nevertheless, the artificial intelligence (AI) results were based on only 2-3 overlapping pulse data and did not consider the effect of noise, so they did not solve realistic problems. Additional research is needed. In the future, we plan to conduct signal correction research using ≈10×10 mm small size detectors (GAGG, CZT etc.). Also, the performance evaluation of the measurement/analysis system is intended to be performed in an environment similar to the high radiation field of an actual nuclear facility.

Radioactive liquid waste generated during the operation of domestic nuclear power plants is treated through a somewhat different liquid radwaste system (LRS) for each plant. Prior to the introduction of standard nuclear power plants, LRS used a concentrated water dry system (CWDS) to evaporate liquid waste and manage it in the form of dry powder. The boron-containing radioactive liquid waste dry powder was solidified using paraffin from 1995 to 2010, and about 3,650 drums (based on 200 L) of paraffin solidified drums are currently stored in nuclear power plants. Paraffin solidification drums do not meet the acceptance criteria for radioactive waste repositories because it is difficult to secure the homogeneity of the solidified body and there are concerns about leaching of radioactive waste due to the low melting point of paraffin. In order to solve this problem and safely permanently dispose of paraffin solidification drums, the characteristics of dry powder paraffin solidification drums containing boron-containing radioactive liquid waste must be analyzed and appropriate treatment technology utilizing the results must be introduced. This study analyzes the physical properties of paraffin, the chemical properties of boron-containing radioactive waste dry powder, and the physicochemical properties of paraffin solidification powder, and proposes an appropriate alternative technology for treating boron-containing radioactive waste dry drum. When disposing of the paraffin solidification drum with boron-containing radioactive liquid waste dry powder, the solidification body must be effectively withdrawn from the drum and the paraffin must be completely separated from the solidification body. When disposing the drum, the solidified material must be effectively extracted from the drum and the paraffin must be completely separated from the solidified material. Afterwards, the paraffin must be self-disposed, and the radioactive waste must be disposed of in accordance with acceptance criteria of repository. We looked at how each characteristic of the paraffin solidification drum with boron-containing radioactive liquid waste dry powder can be utilized in each of the above treatment processes.

Nuclear power plants use ion exchange resins to purify liquid radioactive waste generated while operating nuclear power plants. In the case of PHWR, ion exchange resins are used in heavy water and dehydration systems, liquid waste treatment systems, and heavy water washing systems, and the used ion exchange resins are stored in waste resin storage tanks. The C-14 radioactivity concentration in the waste resin currently stored at the Wolseong Nuclear Power Plant is 4.6×106 Bq/g, exceeding the low-level limit, and if all is disposed of, it is 1.48×1015 Bq, exceeding the total limit of 3.04×1014 Bq of C-14 in the first stage disposal facility. Therefore, disposal is not possible at domestic low/medium-level disposal facilities. In addition, since the heavy water reactor waste resin mixture is stored at a ratio of about 20% activated carbon and zeolite mixture and about 80% waste resin, mixture extraction and separation technology and C-14 desorption and adsorption technology are required. Accordingly, research and development has been conducted domestically on methods to treat heavy water waste resin, but the waste resin mixture separation method is complex and inefficient, and there are limitations in applying it to the field due to the scale of the equipment being large compared to the field work space. Therefore, we would like to introduce a resin treatment technology that complements the problems of previous research. Previously, the waste resin mixture was extracted from the upper manhole and inspection hole of the storage tank, but in order to improve limitations such as worker safety, cost, and increased work time, the SRHS, which was planned at the time of nuclear power plant design, is utilized. In addition, by capturing high-purity 14CO2 in a liquid state in a high-pressure container, it ensures safety for long-term storage and is easy to handle when necessary, maximizing management efficiency. In addition, the modularization of the waste resin separation and withdrawal process from the storage tank, C-14 desorption and monitoring process, high-concentration 14CO2 capture and storage process, and 14CO2 adsorption process enables separation of each process, making it applicable to narrow work spaces. When this technology is used to treat waste resin mixtures in PHWR, it is expected to demonstrate its value as customized, high-efficiency equipment that can secure field applicability and safety and reflect the diverse needs of consumers according to changes in the working environment.

Spent nuclear fuel management is a high-priority issue in South Korea, and addressing it is crucial for the country’s long-term energy sustainability. The KORAD (Korea Radioactive Waste Agency) is leading a comprehensive, long-term project to develop a safe and effective deep geological repository for spent nuclear fuel disposal. Within this framework, we have three primary objectives in this work. First, we conducted statistical analysis to assess the inventory of spent nuclear fuel in South Korea as of 2021. We also projected future generation rates of spent nuclear fuels to identify what we refer to as reference spent nuclear fuels. These reference spent nuclear fuels will be used as the design basis spent fuels for evaluating the safety of the repository. Specifically, we identified four types of design basis reference spent nuclear fuels: high and low burnup from PLUS7 (with a 16×16 array) and ACE7 (with a 17×17 array) assemblies. Second, we analyzed radioactive nuclides’ inventory, activities, and decay heats, extending up to a million years after reactor discharge for these reference spent nuclear fuels. This analysis was performed using SCALE/TRITON to generate the burnup libraries and SCALE/ORIGEN for source term evaluation. Third, to assess the safety resulted from potential radioactive nuclides’ release from the disposal canister in future work, we selected safety-related radionuclides based on the ALI (Annual Limit of Intake) specified in Annex 3 of the 2019-10 notification by the NSSC (Nuclear Safety and Security Commission). Conservative assumptions were made regarding annual water intake by humans, canister design lifetime, and aquifer flow rates. A safety margin of 10-3 of the ALI was applied. We selected 56 radionuclides that exceed the intake limits and have half-lives longer than one year as the safety-related radionuclides. However, it is crucial to note that our selection criteria focused on ALI and half-lives. It did not include other essential factors such as solubility limits, distribution coefficients, and leakage processes. So, some of these nuclides can be removed in a specific analysis area depending on their properties.

Insects, including aphids, caterpillars, and beetles, have a significant impact on biodiversity, ecology, and the economy by consuming various plant tissues like leaves, stems, and fruits, leading to issues such as holes, defoliation, and impaired growth. Consequently, our study's primary goal was to establish a model system capable of identifying and tracking insects, covering aspects like their behaviors, movements, sizes, and patterns. Our research has successfully produced a 3D monitoring system specifically designed for continuous insect tracking by applying it to brown planthopper. This technology allows for in-depth exploration of insect behaviors and their interactions with plants and crops. The potential applications of this technique are highly promising, offering valuable assistance to researchers in unraveling insect behavior and ecological dynamics and driving further advancements in these crucial research areas.