In case of performing asphalt pavement overlay on existing concrete pavement layer, applying asphalt emulsion tack-coating or spreading prime-coating is considered to improve adhesion between asphalt and concrete layer. After coating work is done a curing process is considered not only for promoting evaporation process in coated (and/or spread) asphalt emulsion, but also for generating a membrane which can act as a bonding agent. Finally, asphalt overlay construction is performed when this curing process is completely done. However, during asphalt overlay construction process remarkable amount of spread tack-coating layer is lost due to asphalt material transfer vehicles (e.g. trucks, approximately 40~50% of total spread tack coating material is lost). In this paper, a new pavement equipment contains simultaneous asphalt emulsion spreading ability and corresponding construction techniques are introduced. Through applying this equipment, non-stop two step sequent working process: spreading asphalt emulsion on to existing concrete pavement layer then paving asphalt material for overlay construction, is available. During pavement working process temperature of asphalt material was kept with ranged between 130ºC and 170ºC. After performing field performance evaluation, it was found that crucial improvement in pavement layer adhesion, crack and rutting resistant ability were observed compared to the conventional paving method.

The paper presents various investigations conducted for evaluation of the performance of polymer combined Vacuum Tower Bottom (VTB) modified asphalt mixes by comparison with different modified mixes in the laboratory scale. In order to verify the possibility of polymer combined VTB as a modifier in the asphalt binder, one base unmodified binder and two different types of modified asphalt binders well known for their good performance in the field were compared in the laboratory scale by rheological performance tests. Frequency Sweep Test (FST) and Multi Stressed Creep and Recovery (MSCR) test with DSR (Dynamic Shear Rheometer) were performed and confirmed its good performance. Secondly, various performance tests were adopted for various modified asphalt mixtures with same aggregate gradation and asphalt binder content. As to evaluate the overall performance, crack resistance and durability of dense graded mixtures, Dynamic modulus tests, Semi Circular Bending (SCB) tests and Cantabro tests were conducted for different types of mixes, respectively. Variance tests and analysis concluded several results. In the case of binder, the polymer combined VTB modifier is the primary affecting factor in performance upgrade when comparing with other binder types including base binder. The modified effects on mixtures were clearly shown in all performance tests although performance ranking out of various test types were different. Dynamic modulus are higher at low temperature and high reduced frequency while smaller modification effects in high temperature and lower reduced frequency. According to SCB test results, fracture resistance could be better than other mix types while durability of them are relatively lower. It can be concluded that polymer base VTB modifier can be act as a good modifier with increasing stiffness and fracture energy from test results. However, there are a couple of concerns remained in terms of performance verification of modifier. Therefore it is required to conduct performance simulation with MEPDG and field verification test and monitoring performance.

PURPOSES : The study aims to predict the service life of national highway asphalt pavements through deep learning methods by using maintenance history data of the National Highway Pavement Management System. METHODS: For the configuration of a deep learning network, this study used Tensorflow 1.5, an open source program which has excellent usability among deep learning frameworks. For the analysis, nine variables of cumulative annual average daily traffic, cumulative equivalent single axle loads, maintenance layer, surface, base, subbase, anti-frost layer, structural number of pavement, and region were selected as input data, while service life was chosen to construct the input layer and output layers as output data. Additionally, for scenario analysis, in this study, a model was formed with four different numbers of 1, 2, 4, and 8 hidden layers and a simulation analysis was performed according to the applicability of the over fitting resolution algorithm. RESULTS: The results of the analysis have shown that regardless of the number of hidden layers, when an over fitting resolution algorithm, such as dropout, is applied, the prediction capability is improved as the coefficient of determination (R2) of the test data increases. Furthermore, the result of the sensitivity analysis of the applicability of region variables demonstrates that estimating service life requires sufficient consideration of regional characteristics as R2 had a maximum of between 0.73 and 0.84, when regional variables where taken into consideration. CONCLUSIONS : As a result, this study proposes that it is possible to precisely predict the service life of national highway pavement sections with the consideration of traffic, pavement thickness, and regional factors and concludes that the use of the prediction of service life is fundamental data in decision making within pavement management systems.

PURPOSES: Case studies of an asphalt-overlay project with a performance-based contract method were conducted on a national highway in Korea to evaluate the effect of the method on asphalt pavement maintenance. This study evaluated the procedure of the performance-based contract method. METHODS: In this study, an asphalt-pavement maintenance project for a national highway was assessed with a performance-based contract to investigate the advantage of the new contract procedures. This is the first trial applying the performance-based contract to a pavementrehabilitation project in Korea. In the four case studies, the warranty period of the performance-based contract was designed for seven years. The research team monitored the construction site to compare the normal contract method with the performance-based contract method. The case studies’project sites were investigated after the end of the construction. RESULTS : Based on the limited case studies, the performance-based contract method could extend the service life of the asphalt pavement and reduce the pavement-maintenance budget because the quality control was well managed by the contractors. However, a few construction laws would be necessary to apply the performance-based contract method in the future. CONCLUSIONS : Using the performance-based contract, the construction company made great efforts to guarantee the warranty period and to apply the optimal maintenance method, based on the pavement distress condition. The contractor and the agency would need to understand the new performance-based contract system for it to be activated. Therefore, a proper education program for the performancebased contract system would be needed to educate the stakeholders regarding the procedures and their effects on the pavement management and maintenance.

PURPOSES : In this study, the pavement condition of non-mill-and-overlay and mill-and-overlay on deteriorated concrete pavement was compared. In addition, the suitable time to perform the initial overlay was investigated.METHODS : The condition of the pavement sections that were not additionally overlaid on non-mill-and-overlay or mill-and-overlay on deteriorated concrete pavements was investigated according to overlay pavement age. The condition of non-mill-and-overlay and mill-andoverlay sections of expressway route 25, which has more information on overlay history than other routes, was compared according to the number of times of overlay. The relation between the concrete pavement condition just before the overlay and the number of times of overlay was investigated for the non-mill-and-overlay and mill-and-overlay sections for which the first overlay was performed in the same year.RESULTS: The pavement condition of the non-mill-and-overlay sections was better than that of the mill-and-overlay sections, showing higher Highway Pavement Condition Index(HPCI) regardless of overlay pavement age. The number of reflection crackings of the non-mill-and-overlay sections was smaller than that of the mill-and-overlay sections. As a result of observing the cores obtained from the overlay sections, the proportion of the deteriorated non-mill-and-overlay sections was smaller than that of the mill-and-overlay sections. The SD measured just before the overlay on the concrete pavement for which additional overlay was not performed was smaller than that for which additional overlay was performed regardless of the milling of the concrete slab surface. The HPCI of the concrete pavement for which overlay was performed just once was higher than that for which overlay was performed more than one time.CONCLUSIONS : Accordingly, it was concluded that the condition of the non-mill-and-overlay sections was better than that of the milland-overlay sections. In addition, the better the condition of concrete pavement just before the initial overlay, the longer the duration of the overlay effect.

PURPOSES : The purpose of this study is to develop a regression model to predict the International Roughness Index(IRI) and Surface Distress(SD) for the estimation of HPCI using Expressway Pavement Management System(PMS).METHODS : To develop an HPCI prediction model, prediction models of IRI and SD were developed in advance. The independent variables considered in the models were pavement age, Annual Average Daily Traffic Volume(AADT), the amount of deicing salt used, the severity of Alkali Silica Reaction(ASR), average temperature, annual temperature difference, number of days of precipitation, number of days of snowfall, number of days below zero temperature, and so on.RESULTS : The present IRI, age, AADT, annual temperature differential, number of days of precipitation and ASR severity were chosen as independent variables for the IRI prediction model. In addition, the present IRI, present SD, amount of deicing chemical used, and annual temperature differential were chosen as independent variables for the SD prediction model.CONCLUSIONS: The models for predicting IRI and SD were developed. The predicted HPCI can be calculated from the HPCI equation using the predicted IRI and SD.

PURPOSES : So far, aged cement concrete pavement on express highways has been rehabilitated mainly with asphalt concrete inlay. However, potholes were the major problem, and they shortened the life of the inlay mainly owing to the poor drainage of water once it infiltrated the interface of the concrete and asphalt. The purpose of this study is to compare the performance and economic efficiency of asphalt overlay and inlayMETHODS: Overlay and inlay were compared through accelerated pavement testing, and a life-cycle cost analysis was conducted in this study using the CA4PRS program.RESULTS and CONCLUSIONS : It was found from accelerated pavement testing that the overlay exhibited reflective crack resistance that was more than twice as effective as that of inlay. The total cost (construction cost + user cost) within the analysis period (20 years) of the overlay was 37% lower than that of the inlay.

PURPOSES: This study develops eco-friendly asphalt reinforcement materials applicable to bridge deck pavement. The main purpose is to ensure highly reliable quality applicable to structures and the possibility of practical application. The main target of the study is to develop materials that are environmentally friendly and capable of improving performanceMETHODS: The application of double-reinforcement fiber improves the performance of the road pavement. 1. We use recycled film for application of sheet-typed reinforcement. 2. We use preprocessing fibers to reinforce the properties of composite pavement materials.RESULTS : The developed products may produce materials that fit the purpose of achieving stability and environmental friendliness. Sheettyped reinforcements use more than 50% recycled resin. The most important type of damage to the asphalt layer is deflection (plastic deformation). These products have a very high deflection resistance of not less than 6,000 cycles/mm. In addition, all performance is excellent. Thus, it will be easier to access the field in the future.CONCLUSIONS: Fiber-reinforced asphalt pavement showed excellent performance. Sheet-typed reinforcements containing 50% recycling resin produced good performance in terms of functionality as well as environmental friendliness. Thus, enhancing the field applicability will enhance the usability of the reinforcements.

PURPOSES: This study aims to develop a rational procedure for estimating the pavement roughness index considering vehicle wandering. METHODS: The location analysis of the passing vehicle in the lane was performed by approximately 1.2 million vehicles for verification of the wandering distribution. According to verification result, the distribution follows the normal distribution pattern. The probability density function was estimated using each lane's wandering distribution model. Then the procedure for applying a weighted value into the lane profile was conducted using this function. RESULTS : The modified index, MRIw, with consideration towards applying the wandering weighted value application was computed then compared with MRI. It was found that the Coefficient of Variation for distribution of lateral roughness index in the lane was high in the case of a large difference between each index (i.e., MRIw and MRI) observed. CONCLUSIONS : This result confirms that the new procedure with consideration of the weight factor can successfully improve the lane representative characteristics of the roughness index.

PURPOSES : The purpose of this study is to verify the effects of fiber grid reinforcement on the thickness reduction of asphalt pavement. Test sections were constructed on the national highway to evaluate the structural capacity of asphalt pavement with the reinforced fiber grid and normal asphalt pavement. METHODS: Falling Weight Deflectometer (FWD) tests were performed to measure the structural capacity of test sections. The loads of the FWD test are 4.1 ton, 8.0 ton, 10.0 ton, and loaded twice, respectively. The test sections consist of a reference asphalt pavement section, an asphalt pavement section reduced with a 5-cm base layer thickness, and a fiber grid reinforced asphalt pavement section reduced with a 5-cm base layer thickness. In addition, strain data was collected using strain gauges installed in the test sections. RESULTS: The results of the FWD tests showed that the deflections of the pavement section reinforced with the fiber grid was reduced by about 14% compared with that of the reference asphalt pavement section. The strain at the bottom of the asphalt surface layer of the pavement section reduced to a 5-cm base thickness and reinforced with a fiber grid was similar to that at the bottom of the asphalt layer of the reference asphalt pavement. CONCLUSIONS : The results of the FWD and strain tests showed the possibility of the pavement thickness reduction by reinforcement with a fiber grid.

PURPOSES : The purpose of this study is to suggest the construction and quality control method for the re-repair of a deteriorated partial depth repair for sections of Portland cement concrete pavement. METHODS : An experimental construction was conducted to extend the repair width for removing an existing repair section. A removal method was used to ensure early performance for a deteriorated partial depth repair section. Bond strength and split tensile strength were measured at the near vertical interface layer between the existing pavement and repair material. The area was analyzed for various conditions such as the extended repair area and the removing method of the existing repair section. RESULTS : As a result of analysis of bond strength and split tensile strength, the bonding performance of a milling removed section was improved over a cutting and hand breaker removed section. The bond strength was analyzed to increase slightly as the extended repair width for removing the existing repair section increased. The split tensile strength did not show a clear relationship to an increased extended repair width of an existing removed repair section. CONCLUSIONS: The milling removal method should be applied in the removal of existing deteriorated partial depth repair sections. The extended repair width for a re-repair section should be wider than the existing partial depth repair with at least a 75-mm length and width for the bond strength and the split tensile strength.

PURPOSES : One of the main components of road projects funded by the Economic Development Cooperation Fund (EDCF) is the improvement or rehabilitation of existing pavements. The result is that pavement structures are critical to the success of a project. There is, however, no design standard available at present that reflects a region's specific features including climate conditions and quality of pavement materials. For this reason, a comparative study of the major EDCF borrowers' flexible pavement design standards was conducted. This study led to the proposal of a new method for applying flexible pavement designs which can be used for EDCF-funded projects in Asia. METHODS : The method has been produced by adjusting some input data of the "AASHTO Interim Guide for Design of Pavement Structures" in accordance with certain Asian countries' geometrical features, tropical and subtropical weather, and strength of pavement materials. The Philippine regional factors, having five different grades, have been selected after taking into consideration the amount of rainfall, strength of pavement materials, and characteristics of the Asia and Pacific regions. Structural layer coefficients have been prepared for two different regions according to the geometric difference between Southeast and Southwest Asia. The Philippine and Sri Lankan coefficients have been used for Southeast Asia and Southwest Asia, respectively. CONCLUSIONS : Owing to applying this new method, it was verified that the thickness of the pavement was underestimated by between 11 cm and 16 cm compared with the originally designed thickness. Having discovered that the use of the Korean and Americanoriented factors and coefficients is not appropriate for other Asian countries, the new method is expected to enhance the quality of pavement in future projects.

PURPOSES : This research was a laboratory study for evaluating the Reclaimed Asphalt Pavement (RAP) mixture added developed rejuvenator for warm mix recycling. Waste asphalt mixtures occupy about 18.2% of construction wastes in Korea. Moreover, most rejuvenators were imported from Europe or the U.S. Therefore, improving usage of RAP with a developed rejuvenator material provides environmental protection at a reduced cost. METHODS : The specimen used for this experiment was performed by only using RAP. A suitable rejuvenator for Target PG was then added. In addition, a conventional rejuvenator was selected to compare performance and specimens introduced with the same procedure as the developed rejuvenator was prepared. In order to evaluate rutting resistance and water susceptibility, we conducted a deformation strength test, a tensile strength ratio test, and a dynamic immersion test with the prepared mixtures. RESULTS: Laboratory test results indicated that both the developed additive and conventional additive improved performance of the recycled asphalt mixtures compared to mixtures without the rejuvenator. In addition, the deformation strength test and TSR test results satisfied standards for domestic recycling asphalt mixtures. The dynamic immersion test showed that the developed rejuvenator has superior scaling resistance than the conventional rejuvenator. CONCLUSIONS : In terms of rutting resistance and moisture susceptibility, the warm mix recycled asphalt mixtures with the developed rejuvenator appeared to effectively recovered performance.

PURPOSES : This study is aimed at development of a stochastic pavement deterioration forecasting model using National Highway Pavement Condition Index (NHPCI) to support infrastructure asset management. Using this model, the deterioration process regarding life expectancy, deterioration speed change, and reliability were estimated. METHODS: Eight years of Long-Term Pavement Performance (LTPP) data fused with traffic loads (Equivalent Single Axle Loads; ESAL) and structural capacity (Structural Number of Pavement; SNP) were used for the deterioration modeling. As an ideal stochastic model for asset management, Bayesian Markov multi-state exponential hazard model was introduced. RESULTS: The interval of NHPCI was empirically distributed from 8 to 2, and the estimation functions of individual condition indices (crack, rutting, and IRI) in conjunction with the NHPCI index were suggested. The derived deterioration curve shows that life expectancies for the preventive maintenance level was 8.34 years. The general life expectancy was 12.77 years and located in the statistical interval of 11.10-15.58 years at a 95.5% reliability level. CONCLUSIONS : This study originates and contributes to suggesting a simple way to develop a pavement deterioration model using the total condition index that considers road user satisfaction. A definition for level of service system and the corresponding life expectancies are useful for building long-term maintenance plan, especially in Life Cycle Cost Analysis (LCCA) work.

도시 열환경 개선을 위해 국내외 도로포장 분야에서 다양한 연구가 진행 중에 있으며, 태양의 근적외선 반사를 통해 노면의 온도를 저감하는 반사형 차열성 포장 공법도 그 일환으로 연구와 실용화가 진행되어 왔다. 특히 일본의 도쿄도에서는 2002년 9월에 ‘살수를 필요로 하지 않는 포장노면의 온도상승을 억제하는 신기술’을 주제로 공모를 실시하여, 국토교통성 관동지방정비국 내에 ‘환경포장 동경 프로젝트’ 일환으로 차열성 포장과 보수성 포장에 대한 소규모 공개 시험시공을 추진하였다. 국내에서는 2005년 12월부터 수행된 ‘장수명 친환경 도로포장 재료 및 설계시공 기술개발’의 세부 연구과제로 ‘도심지 열섬완화를 위한 포장시스템개발’에서 주차장 부지를 배수성 포장으로 개량한 후 차열성과 투수성 포장에 대한 시험시공 및 추적조사를 실시하였다. 이러한 연구를 토대로 서울시에서는 2009년, 2010년 공용 중인 도로에 차열성 포장 시험시공을 실시하였으나 내구성이 미흡하여 6개월만에 조기파손이 발생하였다. 본 연구는 반사형 도료를 이용한 차열성 포장의 현장공용성 향상을 위해 개선된 차열성 도료를 개발하였다. 이에 대하여 내마모성 실내시험, 포장가속시험을 통한 공용성 평가시험, 주차장 진입구간 시험시공을 통한 내마모성 및 노면온도 저감 효과를 분석하였다. 차열성 포장의 현장공용성 및 노면온도 저감 효과를 평가하기 위해 기존 아스팔트 포장(장기공용으로 골재노출), 국외 우수 반사도료 개량형(A), 미끄럼방지 도료 개량형(B)을 대상으로 시험을 실시하였다. 시험 결과 도료 A, B 모두 내마모 시험(SPS-KTS 1102-1890:2005)에 따른 품질기준(50만회, 1%이하)을 충족하였다. 포장가속시험의 경우 그림 1]의 (b)에서와 같이 시공한지 15일밖에 되지 않는 아스팔트 포장에 도포한 결과 유분이 도료를 용해시켜 충분히 경화되지 않고 분리현상이 발생하였다. 반면 장기 공용한 아스팔트 포장의 경우 약 1년간 추적 조사한 결과 도료의 부착상태가 양호하였다. 따라서 차열성 포장은 신설보다는 유분이 어느 정도 없어진 3∼6개월 후에 적용하는 것이 바람직한 것으로 판단되었다. 온도저감 효과는 기존 아스팔트 포장과 비교하여 약 2.5∼3.5℃로 다소 적게 나타났는데, 이는 장기간 공용으로 아스팔트 바인더가 떨어져나가 표면색이 회색에 가까웠기 때문으로 판단되었다. 따라서 차열성 포장은 아스팔트 바인더가 안정적으로 유지되고 있는 신설포장일수록 상대적으로 온도저감 효과가 크게 나타나며, 노면온도를 상승시키는 근적외선을 반사함에 따라 낮 시간 포장체의 복사열 축적이 저감되어 일몰 후 도심 열섬현상을 완화하는 효과도 기대할 수 있다.

지구온난화가 가중되고 도시가 고도화되면서 우리나라 대도시는 여름철 도시열섬이 빈번히 발생하고 있다. 특히 도심부 도로포장의 대부분을 차지하는 아스팔트 포장은 태양광을 흡수하여 노면온도를 상승시키고 야간에 복사열을 배출함으로써 열대야(최저기온이 25℃ 이상 지속)를 발생시키는 주요 원인이 된다. 이러한 도시 열환경 특성은 노약자 건강을 저해하고 시민의 생활불편을 야기하기 때문에 적극적인 개선방안이 필요하다. 이에 일본에서는 2003년부터 ‘환경포장 동경 프로젝트’ 일환으로 차열성 포장이 대안으로 검토되었다. 유럽의 경우 알베도(Albedo)가 높은 골재를 섞은 포장 재료에 대한 연구가 진행되고 있다. 국내에서도 2005년 정부 연구과제로 반사형 도료를 이용한 열섬저감 포장공법이 진행되었으며, 서울시에서는 2009∼2010년 아크릴계 반사형 도료를 이용한 차열성 포장을 개발하여 시험시공을 실시하였다. 일본과 국내에서 차도에 주로 사용하는 MMA(Methyl Methacrylate)계 반사형 도료는 독특한 냄새 때문에 도심 도로에서 넓은 공간 시공 시 주변 도로 이용자에게 불쾌감을 야기한다. 따라서 현장 적용 시 민원발생 우려가 많으므로 MMA와 같은 반사형 도료의 냄새를 저감하고, 이를 평가할 수 있는 방법에 대한 연구가 필요한 실정이다. 본 연구에서는 기존 MMA를 저취형으로 개량하기 위하여 벌크형 중합반응이 아닌 에멀전 중합반응(또는 수용성)으로 MMA를 형성하였다. 이로 인하여 기존 MMA에 비해 내구성과 내마모성이 낮아진 것을 보완하기 위하여 외부 환경에 따라 쉽게 구조가 파괴되는 단량체(Monomer)의 일부를 폴리머(Polymer)로 대체하였다. 다양한 구성비에 대하여 시험한 결과 단량체와 폴리머의 비율이 1 : 3인 경우 최적인 것으로 나타났다. 또한 환경부 악취물질 관련기준과 평가방안(공기희석 관능시험법, KS Q ISO 5496)을 반사형 도료에 대한 정량적 냄새평가 방안으로 제안하였다. 제안된 평가 방안으로 개발된 반사형 도료와 기존 미끄럼방지 포장용 도료를 비교평가 한 결과, 기존 미끄럼방지 포장용 도료의 경우 희석배수가 약 1,442인 반면 개발된 도료의 경우 희석배수가 10 이하로 무취에 가까운 저취형으로 확인되었다. 이를 토대로 향후 반사형 도료에 대한 냄새평가 및 현장적용 가능 여부 판단에 대한 기초자료로 활용될 것을 기대한다.

One of the most innovative approaches for maintaining and rehabilitating the Seoul pavement is to develop and implement the maintenance of pavement under the pavement management system (PMS). This paper documents result of the survey on PMS used in Seoul. This model is uses the theory to survey the condition of the pavement ,An index called the Distress Manifesto Index (DMI) is define as used to measure the pavement distress condition of the Seoul pavement. And there is Riding Condition Index (RCI) is to define the comfort of driver who is traveling on the Seoul pavement. Pavement condition index is defined as used to evaluate pavement condition. The cost effective PMS is possible only when maintenance requirement are identified at right time with realistic prediction of overall pavement condition. For Seoul, several survey are used in order to management decisions such as Pavement Serviceability Index (PSI), Surface Condition Ratting (SCR), and Pavement Condition Rating (PCR) etc. the goal of this paper is to evaluate the condition of pavement to facilitate a better understanding of the opportunities to augment the current framework while remaining consistent with the aims of moving ahead for progress in 21stcentury. This research is based on the performance of the asphalt concrete pavement data of Seoul Pavement. Pavement are divided into three classes Class 1 consist of 10-7 SPI result data ,that the pavement is in good condition. Class 2 consist of 6.99-4.0 SPI result data , that the pavement is in average condition. Class 3 consist of 3.99-0.00 PCI result data, that the pavement is in bad condition and need to repair immediately. the performance data is from Dongsomoonlo(28) it consist of Rutting ,Cracking, and IRI data.

최근 건설재료의 자가치유 기술에 대한 많은 관심을 보이고 있으며, 유럽의 배수성 포장에 자가치유 아스팔트 포장 기술과 배수시설에 박테리아를 이용한 자가치유 콘크리트를 개발하고 있다. 본 연구에서는 유도가열 장치를 이용한 자가치유 아스팔트 포장의 자가치유 성능을 평가하고자 하였다. 스틸섬유를 아스팔트 포장에 혼입하여 아스팔트 포장을 만든 후 3점 피로균열 시험으로 균열을 유도하였다. 유도가열 장치를 이용하여 가열한 후 2-3시간의 휴지기간을 두어 3점 피로균열 시험을 다시 수행하여 자가치유 가능성을 평가하였다. 일반 골재뿐만 아니라 스틸글래그로 아스팔트 혼합물의 가열성능과 자가치유 성능도 평가하였다. 스필섬유의 분포상태를 분석하기 위하여 마이크로 CT-Scan장비를 이용하여 촬영하였다. 시험결과 스틸섬유를 이용하여 제작한 아스팔트 혼합물의 자가치유 가능성이 있었으며, 자가치유 성능정도를 분석하여 최적의 스틸섬유함량을 결정하였다. 다양한 조건에서 자가치유 성능을 평가하였으며, 매우 효과적인 것으로 나타났다

In contemporary society, vibration and noise in the road nearby buildings have become social problems as vehicles operation has increased. Especially, in the case of the building used to art performance, available suitability of the building is tested by the indoor noise class. Therefore, the purpose of this paper is the measurement of the structure-borne noise of Seoul Art Center nearby Umyeonsan tunnel and analyzing the effects of countermeasure to it. To measure the effects of countermeasure, not only structure-borne noise is measured, but also the vibration is measured, before and after the construction of pavement using pad and porous asphalt. Consequently, the sound pressure level in art center 1st floor is reduced after mat pavement method, structure-borne noise that was high in 25Hz wide-band before pavement decreased regardless of experimental vehicle's velocity. Using porous asphalt pavement the noise was reduced about 3 dB(A).