This paper evaluates the adsorptive removal of sunset yellow (SY) from aqueous solutions using a new magnetic glycodendrimer (MGD). To synthesize the MGD, chitosan dendrons were cultivated on amine-functionalized magnetic graphene oxide. A number of analytical methods were employed to physicochemically characterize the synthesized MGD. Batch adsorption conditions were optimized using the Box–Behnken design. An optimized initial SY content of 633 mg/L, an optimized contact time of 33.37 min, and an optimized pH of 3.72 maximized the MGD adsorption capacity to 485 mg/g. The Langmuir isotherm was employed to describe adsorption equilibrium, while adsorption kinetics was studied via the Lagergren kinetics model. The SY adsorption onto the MGD was thermodynamically found to be spontaneous (ΔG° < 0) and exothermic (ΔH° = – 19.120 kJ/mol), leading to a decreased disorder (ΔS° = – 54.420 kJ/mol) in the solid–liquid interface. The MGD showed reusability and unique magnetic characteristics. It was concluded that the MGD could be a potential alternative for the adsorptive and magnetic removal of SY from an aqueous solution.

Flexible supercapacitors (FS) are ideal as power backups for upcoming stretchable electronics due to their high power density and good mechanical compliance. However, lacking technology for FS mass manufacturing is still a significant obstacle. The present study describes a novel method for preparing FS based on reduced graphene oxide (RGO) using the N+ plasma technique, in which N+ reduces graphene oxide on the surface of a cotton/polyester substrate. The effect of aloe vera (AV) as a natural reducing & capping agent and carbon nanotubes (CNT) as nanoconductors on the electrochemical performance of the electrodes is studied. FESEM and XPS were employed to investigate the electrodes' structural and chemical composition of electrodes. The galvanostatic charge–discharge curves of electrodes revealed the enhancement of the electrochemical activity of the as-prepared electrode upon additions of AV and CNT. The areal capacitance of the RGO, RGO/AV, and RGO/ AV/CNT supercapacitors at 5 mV/s was 511, 1244.5, and 1879 mF/cm2, respectively. The RGO electrode showed capacitive retention of 80.9% after 2000 cycles enhanced to 89.7% and 92% for RGO/AV and RGO/AV/CNT electrodes, respectively. The equivalent series resistance of the RGO electrode was 126.28 Ω, decreased to 56.62 and 40.06 Ω for RGO/AV and RGO/ AV/CNT electrodes, respectively.

축산물 중 잔류허용기준이 설정되어 관리하고 있는 농약 azocyclotin, cyhexatin, fenbutatin oxide는 대표적인 유 기주석계 살비제이다. 기존 시험법은 가스크로마토그래피 를 사용하여 정량한계가 높고 분석 시 재현성이 떨어져 이에 대한 개선이 필요한 실정으로 본 연구에서는 비교적 간편하며 시간이 적게 소요되는 QuEChERS법을 활용하여 azocyclotin, cyhexatin, fenbutatin oxide의 시험법을 마련하 고자 하였다. 1% 아세트산을 함유한 아세트산에틸:아세토 니트릴(1:1) 혼합액을 이용하여 진탕 추출 후 d-SPE로 정 제하고 이를 농축 후 LC-MS/MS를 이용한 시험법을 개발 하였다. Azocyclotin, cyhexatin 및 fenbutatin oxide의 결정 계수(R2)는 0.99 이상으로 높은 직선성을 확인하였으며 정 량한계는 0.01 mg/kg으로 높은 감도를 나타내었다. 대표 축산물 5종(소, 돼지, 닭, 계란, 우유)에서 LOQ(0.01 mg/ kg), MRL(0.05 mg/kg), MRL 10배(0.5 mg/kg)의 농도에서 회수율 실험을 한 결과 평균 회수율이 76.4-115.3% 및 84.4-110.8%이었으며, 상대표준편차는 25.3% 이하로 나타 났다. 본 연구는 Codex 가이드라인(CAC/GL 40-1993, 2003) 및 ‘식품의약품안전처 식품의약품안전평가원의 식 품등 시험법 마련 표준절차에 관한 가이드라인(2016)’에 적합한 수준임을 확인하였다. 따라서 본 연구에서 확립한 시험법은 축산물 중 잔류할 수 있는 azocyclotin, cyhexatin, fenbutatin oxide의 안전관리를 위한 공정시험법으로 활용 가능할 것으로 판단된다.

YAG phosphor powders were fabricated by the atmospheric plasma spraying method with the spray-dried spherical YAG precursor. The YAG precursor slurry for the spray drying process was prepared by the PVA solution chemical processing utilizing a domestic easy-sintered aluminum oxide (Al2O3) powder as a seed. The homogenous and viscous slurry resulted in dense granules, not hollow or porous particles. The synthesized phosphor powders demonstrated a stable YAG phase, and excellent fluorescence properties of approximately 115% compared with commercial YAG:Ce3+ powder. The microstructure of the phosphor powder had a perfect spherical shape and an average particle s ize of a pprox imately 30 μm. As a r esult of t he PKG t est of t he YAG p hosphor p owder, t he s ynthesized phosphor powders exhibited an outstanding luminous intensity, and a peak wavelength was observed at 531 nm.

Infrared radiation (IR) refers to the region of the electromagnetic radiation spectrum where wavelengths range from about 700 nm to 1 mm. Any object with a temperature above absolute zero (0 K) radiates in the infrared region, and a material that transmits radiant energy in the range of 0.74 to 1.4 um is referred to as a near-infrared optical material. Germanatebased glass is attracting attention as a glass material for infrared optical lenses because of its simple manufacturing process. With the recent development of the glass molding press (GMP) process, thermal imaging cameras using oxide-based infrared lenses can be easily mass-produced, expanding their uses. To improve the mechanical and optical properties of commercial materials consisting of ternary systems, germanate-based heavy metal oxide glasses were prepared using a melt-cooling method. The fabricated samples were evaluated for thermal, structural, and optical properties using DSC, XRD, and XRF, respectively. To derive a composition with high glass stability for lens applications, ZnO and Sb2O3 were substituted at 0, 1, 2, 3, and 4 mol%. The glass with 1 mol% added Sb2O3 was confirmed to have the optimal conditions, with an optical transmittance of 80 % or more, a glass transition temperature of 660 °C, a refractive index of 1.810, and a Vickers hardness of 558. The possibility of its application as an alternative infrared lens material to existing commercial materials capable of GMP processing was confirmed.

해양산업시설에서는 많은 종류의 유해물질의 배출 가능성이 존재하기 때문에 이에 대한 체계적인 대응체계가 필요하다. 그 중 연속자동 측정이 가능하면서 ppb 수준의 낮은 검출하한 (limit of detection:LOD)를 갖는 센서 구현은 매우 중요하다. 이를 위해 본 연구에서 는 활성탄소(carbon black)와 Indium tin oxide (ITO) 나노입자를 혼합한 film의 표면저항의 변화를 이용한 고성능 센서 제안 및 구현을 위해 성능인자를 최적화하였다. 센서 구조는 접촉 면적과 전극 간격을 최적화하였다. 접촉 면적이 증가하면 감도, LOD 성능이 향상되었으며 60 mm2에서 최적화되었다. 또한, 전극 간격은 접촉 면적을 일정하게 유지한 상태에서 변화시켰으며 센서 응답은 전극 간격이 감소함에 따라 증가하는 것을 확인하였다. 마지막으로 센서 표면에서의 유해물질의 잔류시간 증가를 위해 화학흡착제를 적용하였다. 화학흡착제는 유해 물질을 선택적으로 흡수할 수 있는 polyester계를 선택하였다. 그 결과 농도가 증가함에 따라 응답이 선형적으로 증가하여 센서로 활용이 가능한 것을 확인하였다. 이러한 3가지의 방법을 통해 센서를 제작하였을 때 액상 유해물질을 기존 센서의 LOD(89.9 ppb)와 비교 10~40 ppb 정도의 낮은 농도를 검출할 수 있는 센서를 구현하였다.

Decabromodiphenyl ether (BDE209) is a persistent aromatic compound widely associated with environmental pollutants. Given its persistence and possible bioaccumulation, exploring a feasible technique to eradicate BDE209 efficiently is critical for today’s environmentally sustainable societies. Herein, an advanced nanocomposite is elaborately constructed, in which a large number of titanium dioxide ( TiO2) nanoparticles are anchored uniformly on two-dimensional graphene oxide (GO) nanosheets ( TiO2/GO) via a modified Hummer’s method and subsequent solvothermal treatment to achieve efficient photocatalytic degradation BDE209. The obtained TiO2/ GO photocatalyst has excellent photocatalytic due to the intense coupling between conductive GO nanosheets and TiO2 nanoparticles. Under the optimal photocatalytic degradation test conditions, the degradation efficiency of BDE209 is more than 90%. In addition, this study also provides an efficient route for designing highly active catalytic materials.

The thermoelectric effect, which converts waste heat into electricity, holds promise as a renewable energy technology. Recently, bismuth telluride (Bi2Te3)-based alloys are being recognized as important materials for practical applications in the temperature range from room temperature to 500 K. However, conventional sintering processes impose limitations on shape-changeable and tailorable Bi2Te3 materials. To overcome these issues, three-dimensional (3D) printing (additive manufacturing) is being adopted. Although some research results have been reported, relatively few studies on 3D printed thermoelectric materials are being carried out. In this study, we utilize extrusion 3D printing to manufacture n-type Bi1.7Sb0.3Te3 (N-BST). The ink is produced without using organic binders, which could negatively influence its thermoelectric properties. Furthermore, we introduce graphene oxide (GO) at the crystal interface to enhance the electrical properties. The formed N-BST composites exhibit significantly improved electrical conductivity and a higher Seebeck coefficient as the GO content increases. Therefore, we propose that the combination of the extrusion 3D printing process (Direct Ink Writing, DIW) and the incorporation of GO into N-BST offers a convenient and effective approach for achieving higher thermoelectric efficiency.

Thermite welding is an exceptional process that does not require additional energy supplies, resulting in welded joints that exhibit mechanical properties and conductivity equivalent to those of the parent materials. The global adoption of thermite welding is growing across various industries. However, in Korea, limited research is being conducted on the core technology of thermite welding. Currently, domestic production of thermite powder in Korea involves recycling copper oxide (CuO). Unfortunately, controlling the particle size of waste CuO poses challenges, leading to the unwanted formation of pores and cracks during thermite welding. In this study, we investigate the influence of powder particle size on thermite welding in the production of Cu-thermite powder using waste CuO. We conduct the ball milling process for 0.5–24 h using recycled CuO. The evolution of the powder shape and size is analyzed using particle size analysis and scanning electron microscopy (SEM). Furthermore, we examine the thermal reaction characteristics through differential scanning calorimetry. Additionally, the microstructures of the welded samples are observed using optical microscopy and SEM to evaluate the impact of powder particle size on weldability. Lastly, hardness measurements are performed to assess the strengths of the welded materials.

Iron oxide (Fe2O3) nanoclusters exhibit significant potential in the biomedical and pharmaceutical fields due to their strong magnetic properties, stability in solutions, and compatibility with living systems. They excel in magnetic separation processes, displaying high responsiveness to external magnetic fields. In contrast to conventional Fe2O3 nanoparticles that can aggregate in aqueous solutions due to their ferrimagnetic properties, these nanoclusters, composed of multiple nanoparticles, maintain their magnetic traits even when scaled to hundreds of nanometers. In this study, we develop a simple method using solvothermal synthesis to precisely control the size of nanoclusters. By adjusting precursor materials and reducing agents, we successfully control the particle sizes within the range of 90 to 420 nm. Our study not only enhances the understanding of nanocluster creation but also offers ways to improve their properties for applications such as magnetic separation. This is supported by our experimental results highlighting their size-dependent magnetic response in water. This study has the potential to advance both the knowledge and practical utilization of Fe2O3 nanoclusters in various applications.

본 연구에서는 PVA(Poly Vinyl Alcohol)섬유와 GO(Graphene Oxide)를 혼입한 섬유보강 콘크리트(FRC)의 역학적 특성 을 평가하고자 하였다. GO와 PVA 섬유를 동시에 혼입한 FRC 각각의 재료를 단일로 사용하였을 때보다 기대효과가 다소 미흡 하였지만, 각 재료의 하이브리드화로 인장강도가 개선되면서 PVA 섬유 혼입률 0.1∼0.3%과 GO 혼입률 0.025%에서 우수한 효 과를 얻을 수 있었다. 특히 PVA 섬유는 0.3%로 혼합하였을 때 부작용을 최소화하면서 최대의 효과를 보였지만, 적절한 GO 배 합비를 조절할 필요가 있으며 FRC내 GO와 PVA 섬유의 최적배합을 구하기 위한 추가적인 연구가 필요할 것으로 사료된다.

The present studies explored the possibility of immobilizing phosphocholine (PC) liposomes on the surface of graphene oxide (GO) which was pre-adsorbed with two kinds of enzymes, horseradish peroxidase and glucose oxidase. The transmission electron microscope images showed that the PC liposomes adsorbed onto the GO surface kept integrity. By using 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS)-encapsulated liposomes, a one-step colorimetric assay for glucose was developed. In the presence of glucose, the GO nanocomposites catalyzed the cascade enzymatic reaction producing colorimetric signals directly. Under the optimal conditions, the GO nanocomposites produced linearly increased colorimetric signal with increased concentrations of glucose ranging from 50 to 500 μM. The detection limit was 33 μM. The GO nanocomposites also exhibited good selectivity for the detection of glucose and were able to detect glucose in human serum.

PURPOSES : The purpose of this study is to experimentally analyze the flexural strength characteristics of cement mortar mixtures simultaneously incorporated with graphene oxide (GO) and polyvinyl alcohol (PVA) fibers, and to understand the composite effect of those on enhancing resistance against the initiation and progression of micro-cracks, as well as the control of macro-cracks in flexural behavior. METHODS : Cement mortar(w/c=0.5) specimens for flexural strength test, mixing 6 mm and 12 mm PVA fibers at 1% and 2% volume ratios, were fabricated. Additionally, specimens incorporating GO at a cement weight ratio of 0.05% were prepared for each mixture to analyze the effect of GO. Therefore total eight types of mixture were prepared. The fabricated specimens were subjected to flexural strength tests after curing in waterbath for 7 and 28 days. Concurrently, digital images for analyzing deformation in accordance with loading history were obtained at a rate of 20 Hz using the DIC technique. Through displacement and strain calculation via DIC, the flexural behavior characteristics of the mixtures combined with GO and PVA fibers were precisely analyzed. Furthermore, the composite effect on flexural behavior characteristics when GO and PVA fibers are incorporated was discussed. RESULTS : For the PVA fiber-reinforced cement mortar mixture, the incorporation of 0.05% GO increased the crack initiation load by up to 23%, and the maximum resistive load after cracking by up to 24%. Moreover, introducing GO into the PVA fiber-reinforced mixture increased the flexural strain just before cracking by approximately 30 to 50%, while the maximum resistive load after cracking exhibited similar strain levels with or without GO incorporation. Therefore, under flexural behavior, the integration of GO might delay crack initiation by increasing the strain concurrent with the rise in flexural stress before crack occurrence. It also seems to contribute to reducing crack expansion by synergistically interacting with PVA fibers after crack occurrence. CONCLUSIONS : It was experimentally examined that the flexural strength of PVA fiber reinforced cement mortar is improved by incorporating GO. Moreover, GO enhances resistance of crack occurrance and reduces crack propagation in combination with PVA fibers. This study suggests that simultaneous incorporation of GO and PVA fibers can synergistically improve the performance of cement composites.

The carbon-containing molecule can be used as an NMR probe to explore the acidic and structural features of various catalytic materials. Thereinto, although mesityl oxide (MO) has been extensively employed to determine the acidity of solution and ionic liquid systems, could it be utilized to characterize the acidic properties of solid acid catalysts? In this work, on the basis of a series of isolated Brønsted and Lewis acid models with varied acid strengths, the adsorption configurations and corresponding 13C chemical shifts of adsorbed MO molecules have been comprehensively studied by means of a theoretical investigation approach. Among them, both the 13C chemical shift difference between β and α carbon atoms (Δδ), and the 13C chemical shift of β carbon atoms (δ13Cβ) in adsorbed MO molecules were explicitly demonstrated to be closely related to the intrinsic acid strength of Brønsted acid sites. These correlations could be utilized to quantitatively scale the Brønsted acid strength of solid acid catalysts. Besides, a moderate relationship was theoretically derived for the relevant 13C NMR parameters and intrinsic Lewis acid strength.

In this study platform, electrocatalytic detection of the antibiotic chloramphenicol (CAP) in phosphate buffer (pH 7) was easily achieved using a carbon paste electrode modified with NiO nanoparticles (note NiO-CPE). The peak reduction potential of chloramphenicol on the modified electrode is at (− 0.60 V/NiO-CPE vs. Ag/AgCl), its electrochemical behavior is completely irreversible, and controlled by adsorption phenomena. An excellent electrocatalytic activity has been demonstrated by the modified elaborated electrode towards the NO2 attracting group on the side chain of chloramphenicol. The structure and chemical composition of the NiO-CPE sensor were analyzed by SEM, and the X-ray diffraction results indicated that nickel oxide microcrystals were formed on the carbon sheets. The electrochemical characteristics of the NiO-CPE sensor were examined by cyclic voltammetry and electrochemical impedance spectroscopy in comparison with the unmodified carbon. Since the DPV technique allows plotting the linearity curve between the electrocatalytic current intensity of the Chloramphenicol peak and their concentration, the proposed sensor showed a remarkable detection limit of 1.08 × 10– 8 mol/L M (S/N = 3) and a wide determination range from 100 to 0.1 μM for Chloramphenicol. The developed sensor was successfully applied in the detection of Chloramphenicol in real samples.

Graphene oxide/Iron III oxide (GO: Fe2O3) nanocomposites (NCs) have been topical in recent times owing to the enhanced properties they exhibit. GO acting as a graphene derivative has demonstrated superior features as obtainable in a graphene sheet. Furthermore, the attachment of oxygen functional groups at its basal and edge planes of graphene has allowed for easy metal/oxide functionalization for improved properties harvesting. Fe2O3 nanoparticles (NPs) on the other hand have polymorphic property enabling the degeneracy of Fe2O3 in different phases, thereby resulting in different physical and crystalline properties when used to functionalize GO. The properties of GO: Fe2O3 have been applied to supercapacitor energy harvesting, Li-ion batteries, and biomedicine. The enhanced properties are attributed to the adsorption and electronic structure properties of Fe atoms. In this review, the various synthesis used in the preparation of reduced/graphene oxide: Fe2O3 is discussed. As indicated in the considered literature, the XPS analysis suggests electronic bond interactions between C–C, C–O, C–Fe and Fe–C. The available report on UPS measurements further suggests the formation of mixed states emanating from  and  bonds. The discussed reports further suggest that the various applications based on the harvesting of electronic, electrical, and magnetic properties are due to the ionic and exchange interactions between the different orbital states of carbon, oxygen and iron. The challenges and future prospects of the synthesis and application of GO/Fe2O3 are examined. Graphical abstract showing the process of exfoliation, reduction and functionalization of graphite to produce reduced graphene oxide (rGO).

Confirmation of the thermal behavior of spent fuel is one of the important points in the management of high-level radioactive waste. This is because various fission products exist in spent nuclear fuel, and a management plan according to their behavior is required. Among the fission products, epsilon particles exist in the form of metal deposits and have a great influence on their physical and chemical properties. However, observing the thermal behavior of epsilon particles is important for understanding spent fuel behavior in thermally environment, but it is difficult to maintain a consistent thermal environment. In this work, we report the thermal behaviors study of uranium oxide with epsilon particle using in situ high temperature X-ray diffraction. We measured the variation of temperature on the size of crystalline, which is a cell parameter in the reaction process. And then, the change of lattice parameters is calculated by Rietveld refinement.

Measurement of oxide ion (O2-) concentration is a basic technology required in molten salt fields, from energy storage systems to electrolytic reduction of rare earth elements or spent nuclear fuels. In a molten salt reactor, O2- ions react with actinide elements to form their oxides or oxy-chlorides to induce actinide precipitation, and promote metal corrosion to cause a failure of structural material. For these reasons, removal of O2- ions and monitoring of the O2- concentration in molten salt reactors are essential. In this study, methods using chemical and electrochemical methods were investigated for measuring the concentration of O2- ions in a molten salts. The acid-base neutralization reaction was used as a chemical analysis method. And electrochemical methods using the O2- diffusion limit current and YSZ (yttria stabilized zirconia) indicator electrode were used for measuring the O2- concentration. Finally, a modified method using porous membrane electrode was applied to monitor the O2- concentration. The O2- concentration was measured up to about 2wt% of Li2O by the method using the O2- diffusion current, up to about 4wt% by the YSZ indicator electrode, and about 6wt% by the porous membrane electrode in LiCl molten salts.

Radioactive Oxide is formed on the surface of the coolant pipe of the nuclear power plant. In order to remove the oxide film that is formed on the surfaces of the coolant pipe, chemical and physical decontamination technologies are used. The disadvantage of traditional technologies is that they produce secondary radioactive wastes. Therefore, in this study, the short-pulsed laser eco-friendly technology was used in order to reduce the production of secondary radioactive wastes. It was also used to minimize the damage that was caused to the base material and to remove the contaminated oxide film. The study was carried out using a Stainless steel 304 specimen that was coated with nickel-ferrite particles. Additionally, a transport robot was 3D modeled and manufactured in order to efficiently remove the oxide film from the coolant pipe of the nuclear power plant. The transport robot has a fixed laser head to move inside the horizontal and vertical pipes. The rotating laser head removes the contaminated oxide film on the inner surface of the coolant pipe. In the future, as a condition of the 1064nm short-pulsed laser ablation technique determined by basic analysis, we plan to analyze whether the transport robot is applicable to the radiation contamination site of the nuclear power plant.