Surface plasmon resonance is the resonant oscillation of conduction electrons at the interface between negative and positive permittivity material stimulated by incident light. In particular, when light transmits through the metallic microhole structures, it shows an increased intensity of light. Thus, it is used to increase the efficiency of devices such as LEDs, solar cells, and sensors. There are various methods to make micro-hole structures. In this experiment, micro holes are formed using a wet chemical etching method, which is inexpensive and can be mass processed. The shape of the holes depends on crystal facets, temperature, the concentration of the etchant solution, and etching time. We select a GaAs(100) single crystal wafer in this experiment and satisfactory results are obtained under the ratio of etchant solution with H2SO4:H2O2:H2O = 1:5:5. The morphology of micro holes according to the temperature and time is observed using field emission - scanning electron microscopy (FE-SEM). The etching mechanism at the corners and sidewalls is explained through the configuration of atoms.

Currently, due to the development of technology, the industry is proceeding with the development of advanced materials with high performance such as light weight, heat resistance and electric conductivity. Carbon Fiber Reinforced Plastics (CFRP) is an excellent material with high heat resistance, high strength and thermal shock resistance. In order to obtain excellent hole shape in CFRP drilling, we compared the modified drill shape and the conventional carbide drill. On the other hand, we determine the proper helix angle by observing the CFRP surface according to the helix angle at the trimming of the end mill proceeding after the hole machining.

We synthesized new hole-transporting material, N,N'-diethyl-3,3'-bicarbazyl (E-Cvz-2), 9,9'-diethyl-6-(9-ethyl-carbazol-3-yl)-3,3'-bicarbazole (E-Cvz-3), 6-(9,9'-diethyl-3,3'-bicarbazol-6-yl)-9,9'-diethyl-3,3'-bicarbazole (E-Cvz-4A) and 9-ethyl-6-(9-ethyl-3,9'-bicarbazol-6-yl)-3,9'-bicarbazole (E-Cvz-4B). EL luminance efficiencies of E-Cvz-2, E-Cvz-3, E-Cvz-4A and E-Cvz-4B devices were found to be 4.77, 5.68, 4.27 and 4.64 cd/A, respectively, when synthesized materials are using as a HTL material. The luminance efficiency of E-Cvz-3 is 25% higher than that of NPB, a commercialized HTL material used as a reference in this study.

A new green light emitting compound based on tris (N-methylindolo) benzene (NMTI), anthracene and pyrene was synthesized. NMTI-An and NMTI-Py were used as the light emitting layer of the OLED element to investigate the luminescence characteristics. The OLED device containing NMTI - NPB luminescent layer and hole transport layer (HTL) showed superior characteristics compared to NMTI-Py. The device exhibited maximum EL emission at 502 nm and 550 nm, CIE coordinates (0.38, 0.48) and a luminance efficiency of 2.06 cd/A. Also, when NMTI and NMTI-An were used as HTL instead of NPB, the device containing NMTI-An emitter showed 2.67 cd/A and 2.29 cd/A in luminescence efficiency.

The objective of this study is to investigate the effect of tubular shaft hole length on the A-IMS production process in numerically. The hole length of tubular shaft was changed from 69.5mm to 79.5mm for distribution of load and stress. Then, the tubular shaft was modeled by S20C which was referred to program library. At the same time, the results of numerical analysis were compared in terms of under-fill, metal flow, principal stress, Von-mises stress and load characteristics. In the results, the load and stress were increased at 4 stage when the hole length of tubular shaft was increased. Also, folding phenomenon was observed to intensify as increasing the hole length of tubular shaft by confirmation of metal flow.

We investigate the solar cycle variation of microwave and extreme ultraviolet (EUV) intensity in latitude to compare microwave polar brightening (MPB) with the EUV polar coronal hole (CH). For this study, we used the full-sun images observed in 17 GHz of the Nobeyama Radioheliograph from 1992 July to 2016 November and in two EUV channels of the Atmospheric Imaging Assembly (AIA) 193 A° and 171 A° on the Solar Dynamics Observatory (SDO) from 2011 January to 2016 November. As a result, we found that the polar intensity in EUV is anti-correlated with the polar intensity in microwave. Since the depression of EUV intensity in the pole is mostly owing to the CH appearance and continuation there, the anti-correlation in the intensity implies the intimate association between the polar CH and the MPB. Considering the report of Gopalswamy et al. (1999) that the enhanced microwave brightness in the CH is seen above the enhanced photospheric magnetic field, we suggest that the pole area during the solar minimum has a stronger magnetic field than the quiet sun level and such a strong field in the pole results in the formation of the polar CH. The emission mechanism of the MPB and the physical link with the polar CH are not still fully understood. It is necessary to investigate the MPB using high resolution microwave imaging data, which can be obtained by the high performance large-array radio observatories such as the ALMA project.

Polycrystalline diamond (PCD) tools possessing high hardness and abrasive wear resistance are particularly suited for drilling of carbon fiber reinforced plastic (CFRP) composites, where tool life and consistent hole quality are important. While PCD presents superior performance when drilling CFRP, it is unclear how it performs when drilling multi-stack materials such as CFRP-titanium (Ti) stacks. This comparative study aims to investigate drilling of a Ti plate stacked on a CFRP panel when using PCD tools. The first sequence of the drilling experiments was to drill 20 holes in CFRP only. CFRP-Ti stacks were then drilled for the next 20 holes with the same drill bit. CFRP holes and CFRP-Ti stack holes were evaluated in terms of machined hole quality. The main tool wear mechanism of PCD drills is micro-fractures that occur when machining the Ti plate of the stack. Tool wear increases the instability and the operation temperature when machining the Ti plate. This results in high drilling forces, large hole diameter errors, high surface roughness, wider CFRP exit thermal damage, and taller exit Ti burrs.

Stress on plates may increase in the neighborhood the edges or the holes for rivets or bolts. Excessive stress concentration may lead to severe breakage of the plates. Thus, it is important to conduct optimization of arrangement of holes at the design stage. In this paper, accuracy of FEM analysis was examined for such stress concentration . By changing the hole size on a narrow plate, change of the stress concentration factor(K) was investigated. Additionally, the same experiment was conducted about series of multiple holes on plate to investigate interaction between the adjacent holes. Then, the FEM results were compared to the reference predictions respectively. Finally, a method by which simple stress concentrating situations can be optimized, will be suggested. This method was examined by FEM, and showed similar tendency with the expectation. Therefore, this method can be valuable when arranging the holes on a plate.