이 논문은 자체 개발된 드론을 이용하여 사진측량기술을 적용하여 3차원 수치지표면모델(DSM)개발 연구를 수 행하였다. 이 DSM을 개발하기 위하여 제주도 지역을 선정하여 24장의 사진을 개발된 드론으로 직접 촬영을 수행하였 다. 촬영된 사진의 정확한 3차원 좌표를 부여하기 위하여, 10개의 지표기준점(GCP)점을 선정하여 상대측위 지구위치시 스템(DGPS)측량을 실시하였다. 사진의 정확도를 평가하기 위하여 3개의 GCP점을 선정하여 사진상의 좌표와 지상점의 좌표의 정확도를 비교하였다. 사진좌표계과 지상좌표계의 정확도를 평가한 결과 수평오차는 8.8-14.7 cm로 나타났으며, 연직오차는 12.4 cm로 나타났다. 이 정확도는 국토지리정보원(NGII)이 인정하는 1/1,000 수치지도의 정확도를 가지는 측량결과이다. 이 연구를 통하여 본 연구에서 개발된 드론과 사진측량기법이 제주지역에서 우리가 원하는 DSM자료를 얻는데 유용한 기술임을 알 수 있었다.

This paper presents the novel observation model, called Modified Spherical Signature Descriptor(MSSD), capable of representing 2D image generated from 3D point cloud data. The Modified Spherical Signature Descriptor has a uniform mesh grid to accumulate the occupancy evidence caused by neighbor point cloud data. According to a kind of area such as wall, road, tree, car, and so on, the evidence pattern of 2D image looks so different each other. For the parameter learning of Convolutional Neural Network(CNN) layers, these 2D images were applied as the input layer. The Convolutional Neural Network, one of the deep learning methods and familiar with the image analysis, was utilized for the urban structure classification. The case study on CNN practice was introduced in detail in this paper. The simulation results shows that the classification accuracy of CNN with 2D images of the proposed MSSD was improved more than the traditional methods' one.

PURPOSES: In this study, a three-dimensional nonlinear finite element analysis (FEA) model for airport concrete pavement was developed using the commercial program ABAQUS. Users can select an analysis method and set the range of input parameters to reflect actual conditions such as environmental loading.METHODS : The geometrical shape of the FEA model was chosen by considering the concrete pavement located in the third-stage construction site of Incheon International Airport. Incompatible eight-node elements were used for the FEA model. Laboratory test results for the concrete specimens fabricated at the construction site were used as material properties of the concrete slab. The material properties of the cement-treated base suggested by the Federal Aviation Administration(FAA) manual were used as those of the lean concrete subbase. In addition, preceding studies and pavement evaluation reports of Incheon International Airport were referred for the material properties of asphalt base and subgrade. The kinetic friction coefficient between the concrete slab and asphalt base acquired from a preceding study was used for the friction coefficient between the layers. A nonlinear temperature gradient according to slab depth was used as an input parameter of environmental loading, and a quasistatic method was used to analyze traffic loading. The average load transfer efficiency obtained from an Heavy falling Weight Deflectomete(HWD) test was converted to a spring constant between adjacent slabs to be used as an input parameter. The reliability of the FEA model developed in this study was verified by comparing its analysis results to those of the FEAFAA model.RESULTS : A series of analyses were performed for environmental loading, traffic loading, and combined loading by using both the model developed in this study and the FEAFAA model under the same conditions. The stresses of the concrete slab obtained by both analysis models were almost the same. An HWD test was simulated and analyzed using the FEA model developed in this study. As a result, the actual deflections at the center, mid-edge, and corner of the slab caused by the HWD loading were similar to those obtained by the analysis.CONCLUSIONS : The FEA model developed in this study was judged to be utilized sufficiently in the prediction of behavior of airport concrete pavement.

Defects of zeolite membranes often lower their separation performance. Thus, the investigation of the defects is highly critical in achieving high separation performance. While general characterization methods (e.g. scanning electron microscopy; SEM) that examine the membrane surface cannot detect defects, the FCOM measurement is able to identify the defective structure inside the zeolite membrane using dye molecules of appropriate size [1]. In this work, various dyeing conditions (times and concentrations) were applied to a MFI zeolite membrane in an attempt to investigate the defective structure. Furthermore, the quantitative analysis is practiced to measure the defects in numerical form.

PURPOSES : The piezoelectric energy road analysis technology using a three-dimensional finite element method was developed to investigate pavement behaviors when piezoelectric energy harvesters and a new polyurethane surface layer were installed in field conditions. The main purpose of this study is to predict the long-term performance of the piezoelectric energy road through the proposed analytical steps. METHODS: To predict the stresses and strains of the piezoelectric energy road, the developed energy harvesters were embedded into the polyurethane surface layer (50 mm from the top surface). The typical type of triaxial dump truck loading was applied to the top of each energy harvester. In this paper, a general purpose finite element analysis program called ABAQUS was used and it was assumed that a harvester is installed in the cross section of a typical asphalt pavement structure. RESULTS : The maximum tensile stress of the polyurethane surface layer in the initial fatigue model occurred up to 0.035 MPa in the transverse direction when the truck tire load was loaded on the top of each harvester. The maximum tensile stresses were 0.025 MPa in the intermediate fatigue model and 0.013 MPa in the final fatigue model, which were 72% and 37% lower than that of the initial stage model, respectively. CONCLUSIONS : The main critical damage locations can be estimated between the base layer and the surface layer. If the crack propagates, bottom-up cracking from the base layer is the main cracking pattern where the tensile stress is higher than in other locations. It is also considered that the possibility of cracking in the top-down direction at the edge of energy harvester is more likely to occur because the material strength of the energy harvester is much higher and plays a role in the supporting points. In terms of long-term performance, all tensile stresses in the energy harvester and polyurethane layer are less than 1% of the maximum tensile strength and the possibility of fatigue damage was very low. Since the harvester is embedded in the surface layer of the polyurethane, which has higher tensile strength and toughness, it can assure a good, long-term performance.

Dynamic numerical simulation of pile-supported slab track system embedded in a soft soil and embankment was performed. 3D model was formulated in a time domain to consider the non-linearity of soil by utilizing FLAC 3D, which is a finite difference method program. Soil non-linearity was simulated by adopting the hysteric damping model and liner elements, which could consider soil-pile interface. The long period seismic loads, Hachinohe type strong motions, were applied for estimating seismic respose of the system, Parametric study was carried out by changing subsoil layer profile, embankment height and seismic loading conditions. The most of horizontal permanent displacement was initiated by slope failure. Increase of the embedded height and thickness of the soft soil layer leads increase of member forces of PHC piles; bending moment, and axial force. Finally, basic guidelines for designing pile-supported slab track system under seismic loading are recommended based on the analysis results.

In this study, STS316L powders prepared by gas atomization are used to manufacture bulk structures with dimensions of 10 × 10 × 10 mm3 using selective laser melting (SLM). The microstructures and hardness of the fabricated 316L stainless steel has been investigated with the laser beam overlap varied from 10% to 70%. The microstructures of the fabricated STS316L samples show a decrease in the balling and satellite of powders introducing defect in the bulk samples and the porosity caused by the gap between the molten metal pools disappearing as the overlap ratio increases, whereas a low overlap ratio results in significant balling and a large amount of isolated powders due to the increased gap between the melt pools. Furthermore, the highest value in Vickers hardness is obtained for the sample fabricated by 30% overlapped laser beams. These results show that the overlap ratio of laser beams in the SLM process should be considered as an important process parameter.

Selective laser melting (SLM) can produce a layer of a metal powder and then fabricate a three-dimensional structure by a layer-by-layer method. Each layer consists of several lines of molten metal. Laser parameters and thermal properties of the materials affect the geometric characteristics of the melt pool such as its height, depth, and width. The geometrical characteristics of the melt pool are determined herein by optical microscopy and three-dimensional bulk structures are fabricated to investigate the relationship between them. Powders of the commercially available Fe-based tool steel AISI H13 and Ni-based superalloy Inconel 738LC are used to investigate the effect of material properties. Only the scan speed is controlled to change the laser parameters. The laser power and hatch space are maintained throughout the study. Laser of a higher energy density is seen to melt a wider and deeper range of powder and substrate; however, it does not correspond with the most highly densified three-dimensional structure. H13 shows the highest density at a laser scan speed of 200 mm/s whereas Inconel 738LC shows the highest density at 600 mm/s.

In recent years, the number of earthquakes has increased worldwide. There has been an extreme increase on the Korea Peninsula, which is considered a safety zone for earthquakes. In particular, in the event of earthquakes, most structures on the Korea Peninsula are severely damaged, because most are not designed to withstand them. Damage to and destruction of civil structures, such as bridges, nuclear facilities, and dams, is worse than that of other structures. It is necessary to evaluate and predict the extent of damage by earthquake magnitude, as the magnitude of earthquakes is increasing as well as the frequency. A major feature of the occurrence of earthquakes is uncertainty. For this reason, it is necessary to adopt a stochastic approach, and studies using this approach are increasing. However, although there have been several studies on bridges and nuclear facilities, there have been few studies on probabilistic seismic risk evaluation for multi-functional weirs. Thus, this study presents 3D multi-functional weirs and performs a time history analysis by using LS-DYNA, a general structure analysis program. Probabilistic seismic fragility assessment is conducted by Monte Carlo simulation.

In this study, a numerical approach for automotive louvered fin heat exchanger is carried out to investigate the effect of louvered angle on the heat transfer characteristics. The numerical simulation code STAR-CCM+ is utilized to calculate flow and temperature fields with polyhedral meshes. The results show that the flow efficiency is increased as the louver angle is high. Also, the outlet temperatures are nearly the same according to louver angles because the average Nusselt numbers are nearly equivalent regardless of louver angle.

BIM 설계에서 라이브러리의 구축 및 활용은 매우 중요하다. 기존 컨텐츠의 재활용이 가능하므로, 설계를 보다 효과적이 고 효율적으로 진행할 수 있다. 건축분야와 달리 토목분야, 특히 철도시설분야에서는 라이브러리의 구축 및 표준화가 미진하 다. 따라서 본 연구에서는 철도시설분야에 3차원 객체 라이브러리를 구축하고 표준화하고자 한다. 철도시설물 분류체계 및 관련도면을 수집 및 분석한다. 분석된 표준도면의 항목과 분류체계 항목을 매칭하였다. 각 항목별로 라이브러리가 필요한지 여부와 그럴 경우 어떤 소프트웨어가 적절한지를 검토하였다. 사용가능한 소프트웨어는 주로 Civil 3D와 Revit 등으로 나타 났다. 향후 이를 바탕으로 철도인프라 3차원 라이브러리의 속성 항목 및 명세서를 설계하고 라이브러리를 구축할 예정이다

There is a growing interest in the application of primary hepatocytes for treatment of liver diseases in humans and for drug development. Several studies have focused on long-term survival and di-differentiation blocking of primary hepatocytes in an in vitro culture system. Therefore, the present study also aimed to optimize an in vitro culture system using primary rat hepatocytes. Primary rat hepatocytes from 6-week-old male Crl:CD rats were isolated using a modified two-step collagenase perfusion. Healthy 3.5 × 106 primary rat hepatocytes were seeded into a 2 dimensional (2D) culture in a 25T culture flask coated with collagen type I or into a 3D culture in a 125-ml spinner flask for 7 days. Production of plasma protein (ALB and TF), apoptosis (BAX and BCL2), and CYP (CYP3A1) related genes were compared between the 2D and 3D culture systems. The 3D culture system had an advantage over the 2D system because of the relatively high expression of ALB and low expression of BAX in the 3D system. However, the level of CYP3A1 did not improve in the 3D culture with and without the presence of a dexamethasone inducer. Therefore, 3D culture has an advantage for albumin production and primary rat hepatocyte survivability, but a low expression of CYP3A1 indicated that primary rat hepatocytes require a high–density culture for stress reduction by continuous flow.

All measurements include uncertain factors affecting the result in accordance with environment and conditions. In order to guarantee right decision making and quality improvement, these factors must be found and appropriate actions should be taken. This paper aims to estimate and analyze variabilities found in set-up and as well as measurement uncertainty when using CMM(Coordinate Measuring Machine). Two skilled operators were selected to individually measure a product which was a kind of main part of an engine called connecting rod cap. The results showed that at the least, 10 % was stable while at the most, 30 % was somewhat unstable regarding P, percentage of measuring errors. There was little difference between the two operators on measurement uncertainty expecially considering their degree of freedom based on their objective and subjective judgement of type B uncertainty despite the significant difference between them. Through this research, I have come to a conclusion that a much more detailed analysis on variation factors can be identified in general measurement by using CMM and the result of set-up variability demands specific investigation and efforts to improve operators’ skill or thorough examination on the method of setting product to minimize set-up variability later.