검색결과

검색조건
좁혀보기
검색필터
결과 내 재검색

간행물

    분야

      발행연도

      -

        검색결과 347

        141.
        2013.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this research, the heat and flow analysis in a condenser of vehicle HVAC system was investigated numerically regarding the different shapes of the condenser tube. The velocity, pressure, and temperature distribution of the test fluid(R-134A) inside the tube were numerically calculated for the optimum design of the condenser tube for two different length with four different inlet velocities. In addition, the local pressure and temperature distributions for total tube length were calculated and the variation of pressure drop of the R-134A with flow rate were also calculated numerically. The tube at case 1 with less curved elbows was determined for the better design than case 2 in the aspect of energy-effective shape of the condenser tube.
        4,000원
        142.
        2013.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The present study investigated the blood flow at microvascular network. The role of the blood viscosity and the yield stress of blood on the flow at the microvascular network was examined to find the condition of hemostasis. When the yield stress was less than 0.005Pa, there was no stagnant region in the capillary network used in the study. However, when the yield stress increased to 0.05Pa, stagnant areas began to appear, which grew and expanded rapidly with further increase in the yield stress. From the blood viscosity profile of a patient, one can estimate the yield stress of blood, from which the risk of hemostasis can be determined.
        4,000원
        143.
        2013.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The SMC(Sheet molding compound) process is widely used in the automotive industry to produce parts that are large, thin, lightweight, strong and stiff. Compression molded parts are formed by squeezing a glass fiber reinforced UP(Unsaturated Polyester) sheet, known as sheet mold compound(SMC), between two heated cavity surfaces. This paper has performed flow analysis to predict optimization process of low density SMC. After five types of design variables and six types of response variables were defined, DOE(Design of Experiment) and RSM (Response Surface Method) were applied in order to measure sensitivity of design variables and realize optimization through regression model. After design optimization, the total warpage of the SMC is reduced by about 12% compared to the initial design of SMC and cure time, cure temperature, clamping force and flow pressure are decreased by 0.6∼27% in comparison with the initial design. By doing this, the production costs could be diminished.
        4,000원
        144.
        2013.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        보일러 배기가스를 이용해 온실 내부의 CO2 농도를 높여 식물의 생장을 촉진하는 CO2 시비 시스템의 공급 최적화를 위한 연구를 진행하였다. 다기관의 유로를 사용하는 시비 시스템의 기하학적 변수에 따른 유량균일성 파악을 위해 전산유체역학 기법을 사용하였다. 먼저 PVC 형상을 수정하여, 처음 설비에서 출구유량이 적어 튜브 뒤쪽까지 CO2가 나오지 못했던 문제점을 해결하고 개선된 형상을 결정했다. 그 다음 실험값과 동일하게 맞추기 위하여 실험값과 해석값의 출구 속도를 비교하여 입구 압력을 결정하였다. 이때 여섯 개의 출구에서 나타나는 유량 비균일성은 출구에 Gasket을 부착하여 출구 면적 변화를 통해 유량을 조절할 수 있다고 보았다. 여섯 개의 출구 직경을 각각 변화시킨 3개의 Case 결과가 출구 면적을 모두 동일하게 두었을 때보다 편차가 최대 ±18%까지 감소되었다. 비닐 튜브 역시 뒤쪽까지 CO2가 전달되지 못하는 문제점을 해결하기 위하여 출구의 직경을 변화시켜가며 비교하였다. 각각의 출구 직경은 동일하게 하고 입구 면적 대비 출구 면적이 153.4%(D = 10mm), 97.8% (D = 8mm), 54.9%(D = 6mm)이 되도록 3개의 Case로 나누어 유량 균일성 향상 효과를 알아보았다. 그 결과 출구직경이 10mm일 때보다 6mm일 때, 유량 편차가 ±13% 정도 감소되었다. 따라서 출구 면적이 작아질수록 유량 균일성이 향상됨을 파악하였다. 앞서 결정된 최적 PVC 형상과, 비닐 튜브 조건을 조합하여 전체 형상을 해석한 경우 역시 모든 hole에서의 유량이 0.1g/s 이내의 차이를 보이며 높은 균일성을 나타냈다. 이와 같은 방법으로, 다기관의 유로를 이용하여 CO2를 분배시키는 다른 형태의 시비 시스템에서 역시 PVC 배관에서의 압력강하를 최소화시킨 뒤, PVC와 비닐 튜브의 출구 직경을 변화시키는 순서로 각 출구로의 유량을 균일하게 조정할 수 있을 것으로 판단된다.
        4,000원
        146.
        2013.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The temperature distribution of a generic battery module was analyzed for different flow rates of cooling fluid. For the given battery module design, the temperature of battery cell near the inlet is higher than that of battery cell near the outlet. Because the inlet is located at the higher elevation than the top of battery electrodes, most of the incoming cooling fluid flows directly towards the battery housing wall above the outlet. For the inlet velocities of 1, 3, 5 m/s, the maximum temperature differences are 28, 19, 15 degrees Celcius respectively.
        4,000원
        147.
        2013.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this paper, the current of ECV block is connected to compressor crankcase on which the Pc port of Ps port Euro is formed(Type-1). Pc Port Internal Bellows are supposed to be affected by changes at the flow of refrigerant to the solenoid valve inside inhalation. There is Ps port at the direction of flow characteristic in predicting and analyzing. At suction pressures of 0.2MPa and 1.5MPa, maximum flow rates become 46m/s and 129m/s respectively. The refrigerant is discharged by compressor rotation around the axis of rotation from the inflow of port(Pd)(Type-2). By predicting and analyzing inlet flow, suction pressures become 2.7MPa and 3.6 MPa when maximum flow rates of 177.5m/s and 205m/s are affected on Pc ports of Euros with pressures of 1.2KPa and 3.8KPa respectively. This study result can be applied as the basic data for design of ECV.
        4,000원
        148.
        2013.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        지구 온난화와 이상기후현상으로 인한 온실가스가 증가함에 따라 온실가스 감축을 위해 국가 단위의 온실가스 배출량 산정이 중요해졌다. 따라서 본 연구에서는 평야 지역, 중산간 지역, 산간 지역의 탄소 순환 해석을 통하여 탄소의 흡수 및 배출의 해석을 통한 요인별 원단위를 분석하고 실제지역 구성 비율에 따라 원단위를 적용하여 해석해 보았다. 농촌지역의 탄소배출량을 조사한 결과 그 지역이 평야지역 일 때와 산간지역 일 때의 탄소의 흡수·고정·배출량은 다른 것으로 나타났다. 평야지역의 경우 타지역에 비하여 축사에서 탄소 배출량이 많아서 탄소배출량이 가장 높은 것으로 나타났으며, 임야의 면적이 가장 적은 관계로 탄소 고정량이 가장 적게 나타났다. 중산간지역의 경우 차량에 의한 탄소 배출량이 가장 높게 나타났으며, 임야 면적이 평야지역에 비하여 넓은 관계로 고정량이 높게 나타났으며, 산간지역은 넓은 임야면적 때문에 탄소 고정량이 가장 높은 것으로 나타났다. 본 연구 결과를 통해, 향후 어촌이나 도심지역으로 확대하여 비교·분석한다면 탄소의 흡수·고정·배출량을 관한 기초자료를 확보 할 수 있을 것으로 판단된다.
        4,300원
        150.
        2013.03 KCI 등재 구독 인증기관 무료, 개인회원 유료
        본 연구는 단면변화를 고려한 수위-단면적 변화 및 평 균 유속-단면적 간의 상관관계를 분석하여 유량 산정 및 하천관리에 활용하고자 하였다. 수위에 따른 단면적 변화 는 SB-A 지점은 1.0 m, 1.9 m, SB-C 지점은 0.6 m, 1.8 m, CL-A 지점은 1.0 m, 1.8 m, OS-A 지점은 0.6 m, 2.0m에서 발생되었다. 이 중 첫 번째 변화는 평∙저수기에 해당되 고, 두 번째 변화는 홍수기 및 하천 좌∙우 안에 인위적 ∙자연적으로 형성된 둔치 등으로 판단된다. 수위-단면적 변화에 따른 관계식의 기울기는 지수형 0.5539~1.9013, 선형 9.040~52.544의 범위를 가진다. 기울기는 두 곡선 모두 고수위로 갈수록 증가하는 경향을 보인다. 평균유 속-단면적 변화의 관계는 지수와 직선의 방정식으로 지 수형 기울기와 상관계수는 각각 0.1182~0.8734, 0.22~ 0.86이며, 선형의 기울기와 상관계수는 0.0028~0.1032, 0.20~0.87로 분석되었다. SB-A, SB-C 지점의 저수위는 다른 수위보다 상관관계가 높게 산정되었는데, 이는 수위 구간이 좁고, 하천 단면적의 변화가 크지 않기 때문으로 판단된다. CL-A, OS-A 지점은 월류보의 영향으로 저수위 일 경우에 상관관계가 낮았다. 수위-단면적, 평균유속-단 면적의 상관관계 및 곡선식 등을 이용하여 하천 정비계 획 등의 수립에 활용할 수 있으며, 제외지의 단면적이 변 하는 지점의 유량 변화 등의 예측에 활용할 수 있을 것 이다.
        4,000원
        151.
        2013.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        A numerical analysis was performed to study PEMFC characteristics depending on the flow direction of reactant gas in cathode gas channel using the Fluent. As cathode relative humidity increases, water mass fraction increases due to back diffusion from cathode. For the both of co-flow and counter-flow cases, water mass fraction is higher near the hydrogen inlet region where the chemical reaction rate is high. In overall, counter-flow case gives higher current density compared to co-flow case for the same operating conditions. However, the difference in the current density is not high. The temperature is also higher near the hydrogen inlet region due to the chemical reaction rate for the both of co-flow and counter-flow cases.
        4,000원
        152.
        2013.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        This research aims to investigate the flow analysis of LNG ship due to the different shapes of the ship front. Velocity and pressure distribution of fluid at the front portion of ship are numerically calculated for the optimum ship design of front with three different ship speeds for two different front shapes of ship. These numerical calculations are only applied for the immersed part of ship at the ocean. In addition, the coefficient of pressure drag and total drag are numerically obtained. Ultimately, the energy-efficient shape of LNG ship are determined through two different body shapes with three different ship speeds.
        4,000원
        153.
        2012.10 구독 인증기관·개인회원 무료
        We developed and characterized five polymorphic microsatellites of Nilaparvata lugens from hybridization method using biotin enrichment strategy and two polymorphic microsatellites from Next Generation Sequencing. Also 11 microsatellites that developed by Sun et al. (2011) are employed to carry out genetic analysis of N. lugens in Southeast Asia. The number of alleles per locus ranged from 2 to 12 with an average of 4.63 alleles per locus. The mean observed heterozygosity of the eleven populations ranged from 0.031 to 0.938 and the expected hetetrozygosity ranged from 0.031 to 0.881. Signifiant genetic differentiation was detected among the three N. lugens populations as the FST ranged from 0.028 (Cheong Do and Ha Long) to 0.161 (CH and BN). The results of microsatellite marker suggested that found N. lugens migrated to Korea at least two times in different period or once. Genetic distance of N. lugens between Korea and Hi Pong were mostly closed and genetic distance of Ha Long and HCM were relatively closed. In this study, development of microsatellites should facilitate the study of future population genetics of N. lugens, and eventually elucidate the route of N. lugens migration to Korea. Thus, combining satisfactory microsatellite markers and intensive surveillance methods in paddy field could be easy to understand to the N. lugens migration mechanism.
        155.
        2012.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        본 연구의 목적은 도시고속도로 합류부의 특성 및 실제 교통상황을 고려하여 각 차로별, 구간별로 영향권을 분석하는 것을 목적으로 하였다. 향후에는 본 연구결과를 바탕으로 차로제어시스템(Lane Control System, LCS) 등 운전자 정보제공서비스 및 첨단기술에 적용하여 효율적인 도로이용을 통한 원활한 운행상태유지가 가능할 것이다. 본 연구에서는 속도의 표준편차를 기준으로 고속도로 합류부의 난류현상을 분석한 기존연구를 기반으로, 난류현상 발생정도를 기준으로 한 세분화된 합류부 영향권을 도출하였다. 난류현상을 기준으로 도출한 합류부 영향권은 합류지점을 중심으로 합류지점과 유사한 교통류 특성을 보이는 구간을 합류의 직접영향권으로 도출하였으며, 도출된 결과는 상류부 300m에서 500m구간의 1, 2, 3차로, 합류지점에서 300m지점까지의 전차로 및 하류부 100m지점까지의 전차로, 하류부 100m에서 300m구간의 2, 3차로로 분석되었다.
        4,000원
        156.
        2012.03 구독 인증기관 무료, 개인회원 유료
        This study evaluated a sexed sperm ability to produce embryos by flow cytometer. Hanwoo bulls sperm were separated to X and Y sperm via Hoechst 33342 stained with near UV laser or performed the pre-sorted without near UV laser beam in flow cytometry. Pre-sorted sperm had significantly higher viability (84±1.15 %, p<0.05) compared to other sorted groups in frozen-thawed semen. For fresh semen, pre-sorted sperm had the higher viability (79±3 %, p<0.05) than those of the X and Y sperm (44.7±1.67 and 41.7±1.2 %) separated by differences of DNA content. On the other hand, pre-sorted and X sperm sorted according to differences in DNA content had significantly higher viabilities (24.3±1.2 and 25.7±0.9 %, p<0.05) compared to that of the sorted Y sperm (13.7±1.2 %) in the hypoosmotic swelling test. The proportion acrosome reaction in the sorted X sperm was higher (55.0±1.7 and 45.0±1.5 %) than those of the sorted Y-sperm (32.3±0.9 %, p<0.05). However, the sperm morphologies of the sorted groups were not significantly differences. In conclusion, the sex-sorting procedure by flow cytometry affected some characteristics of Hanwoo sperm. Further study is needed to determine the optimal procedures to enhance male and female embryos and sorting accuracy.
        4,000원
        157.
        2012.03 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this study, 3 kinds of motorbike models in common use are studied by flow analysis. The maximum velocity becomes 20 to 21 m/s at the upper part of models and the maximum air pressure resistances becomes 202 to 229 Pa at the front of models. Model 3 becomes the most uniform flow and model 1 becomes the most nonuniform flow among 3 models. In case of outlet planes on flow models, model 3 has the smallest velocity as maximum velocity of 17.49 m/s among 3 models. Model 3 has also the smallest velocity in case of middle planes on flow models. As model 3 has the most uniform air flow stream and the least air resistance than model 1 or 2, it can be thought to cut down on the power consumption.
        4,000원
        159.
        2011.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The safety at this study is investigated by flow or stress analyses due to configuration or installation direction of fuel tank in the existing CNG bus. In case of the lower ceiling with sharp type, the equivalent stress due to the explosion of fuel tank is less than the type of flat or arc. it becomes safer on passenger. In case of the installation direction of fuel tank in the existing CNG bus, the stress applied on the lower ceiling at transverse direction becomes less than at longitudinal direction. It is more stable on the safety of passenger. The harm on the explosion accident can be prevented by use of the analysis result at this study.
        4,000원
        160.
        2011.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The flow rate analysis for sanitary fixtures has been studied to determine the water supply piping system and size. The study has been carried out to analyze for a various water supply pressure and piping size theoretically. Also, the study has been carried out to analyze for a various water supply piping system experimentally. The water supply pressure is varied from 0.01MPa to 0.07MPa, and the piping size is varied from 6mm to 15mm. The water supply piping systems are one-to-one, all-loop-type, and bathroom-loop-type water supply piping system. The results indicate that the piping size is able to supply water fully in case of smaller than 15mm if the water supply pressure keep an necessary minimum pressure. And the gap of flow rate is very little for the various water supply piping systems
        4,000원