최근 지구온난화로 인해 발생하는 폭우 및 강설과 같은 비정상적인 기상 패턴으로 인해 도로 표면 결빙(블랙 아이스)으로 인 한 사고와 인명 피해가 증가하고 있으며, 이는 주요 문제로 대두되고 있습니다. 이러한 문제를 완화하기 위해 본 연구에서는 열저장 능력을 갖춘 상변화 물질(PCM)을 시멘트 복합재료에 포함시켰습니다. PCM은 상변화 과정에서 열에너지를 흡수, 저장 및 방출할 수 있어 온도 변동으로 인한 결빙을 최소화할 수 있습니다. PCM은 먼저 미세 캡슐화된 후 시멘트 복합재료에 강화되어 기계적 및 열적 성능 검증 연구가 수행되었습니다. 또한, 열전달 효율과 기계적 특성을 향상시키기 위해 다중벽 탄소나노튜브(CNT)와 실리카 퓸이 추 가되었습니다. 미세 캡슐화된 PCM의 열 성능은 열 거동을 측정하기 위한 재료 실험을 통해 검증되었습니다. 이후, 제조된 시멘트 복 합재의 기계적 및 열적 성능 테스트가 그 효과를 평가하기 위해 수행되었습니다. 이러한 테스트 동안 일정 온도와 습도 챔버를 사용한 열 주기 테스트가 열 성능을 검증하기 위해 수행되었습니다. 기계적 성능 실험에서는 CNT와 실리카 퓸의 포함이 미세 캡슐화된 PCM 의 포함으로 인한 강도 저하를 완화하는 것을 확인하였습니다. 더욱이, 열 주기 테스트를 통해 고효율 열저장 시멘트 복합재가 결빙 조건에서도 영하의 온도를 유지할 수 있음을 보여주었으며, 이는 효율적인 열저장 성능을 입증하였습니다.

PURPOSES : This study aimed to develop a transportation-energy linkage model and performance evaluation indicators to improve the sustainability operation and technology of smart city transportation-energy services. METHODS : This study derived a new transportation-energy linkage system model for 15 services designated by the national pilot city. Evaluation indicators for energy-oriented transportation services in smart cities were selected, and a methodological framework was proposed for selecting quantitative evaluation indicators based on text mining and importance-performance analysis (IPA). RESULTS : Twenty indicators, confirmed as crucial for successful transportation-energy linkage in smart cities, were selected. These covered data linkage between services, IoT-based information linkage driving rate, and network and energy efficiency indicators. The proposed quantitative methodological framework can complement expert subjective evaluation by identifying meaningful implications in research literature that experts may have missed. The methodology can consistently derive indicators even when new services are added, aiding policymakers’ decisions. CONCLUSIONS : The methodological framework can contribute to minimizing operational risks in smart city transportation-energy expansion. It can also be used to prioritize service investment in smart cities by estimating benefit effects through quantitative indicators.

Thermoelectric (TE) energy harvesting, which converts available thermal resources into electrical energy, is attracting significant attention, as it facilitates wireless and self-powered electronics. Recently, as demand for portable/wearable electronic devices and sensors increases, organic-inorganic TE films with polymeric matrix are being studied to realize flexible thermoelectric energy harvesters (f-TEHs). Here, we developed flexible organic-inorganic TE films with p-type Bi0.5Sb1.5Te3 powder and polymeric matrices such as poly(3,4-eethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) and poly (vinylidene fluoride) (PVDF). The fabricated TE films with a PEDOT:PSS matrix and 1 wt% of multi-walled carbon nanotube (MWCNT) exhibited a power factor value of 3.96 μW ‧ m-1 ‧ K-2 which is about 2.8 times higher than that of PVDF-based TE film. We also fabricated f-TEHs using both types of TE films and investigated the TE output performance. The f-TEH made of PEDOT:PSS-based TE films harvested the maximum load voltage of 3.4 mV, with a load current of 17.4 μA, and output power of 15.7 nW at a temperature difference of 25 K, whereas the f-TEH with PVDF-based TE films generated values of 0.6 mV, 3.3 μA, and 0.54 nW. This study will broaden the fields of the research on methods to improve TE efficiency and the development of flexible organic-inorganic TE films and f-TEH.

지구온난화 완화를 위한 노력이 전 세계적으로 계속되고 있는 가운데 우리나라는 2030년 온실가스 배출량을 Business As Usual (BAU) 대비 37% 감축하는 목표를 설정하고 이산화탄소 순 배출 제로 달성을 목표로 하는 ‘2050탄소중립 시나리오’를 발표하였다. 이러한 상황에서 케나프 (Kenaf)는 높은 탄소흡수율과 빠른 성장으로 인해 대체 해결방안으로 제안된다. 시료선정에 대한 분석결과, 케나프 잎은 질소 함량이 높아 적합하지 않은 것으로 나타났고, 줄기와 잎-줄기 혼합 케나프는 Biomass-Solid Refuse Fuel (Bio-SRF) 등급을 충족했다. Bio-SRF 등급을 만족하였지만, Bio-SRF 등급으로 이용할 수 있는 활용처가 뚜렷하지 않다. 따라서 케나프의 연료품질을 반탄화 공정을 통해 개선하여 보다 효율적으로 활용하고자 한다. 반탄화 공정의 공시재료로 줄기만 사용하는 것보다 시료 이용률이 높은 잎-줄기 혼합 케나프를 선택하였다. 반탄화 공정은 여섯가지의 공정 온도 (200·210·220·230·240·250℃)와 다른 세 가지 공정 시간(20·30·40 min)에서 수행되었다. 반탄화 공정결과, 공정시간이 길수록 230℃, 240℃, 250℃ 온도에서 질량감소가 크기 때문에 에너지수율이 낮았다. 따라서 본 연구에서는 200℃·20 min, 200℃·30 min, 210℃·20 min, 220℃·20 min의 에너지 수율이 높고 질량감소가 작아 최적 반탄화 공정 조건으로 선정하였다.

정삼투 공정(forward osmosis, FO)은 역삼투 공정(reverse osmosis, RO)에 비해 저압으로 운영되므로 오염 제어, 유지 보수, 막 세정 및 잠재적 에너지 저감 측면에서 큰 이점이 있어 다양한 분야에 적용할 수 있는 기술이다. 특히, 정삼투 공정의 막오염층이 비교적 느슨하고 분산된 특성을 가지므로 역삼투 공정과 달리 물리세정만으로도 충분한 막오염 제어가 가능하다. 하지만 기존 연구들의 경우 정삼투 물리세정에 적합한 세정 유속을 적용하지 않아 최적화 운전을 하지 못했다는 한계가 있다. 따라서 이 연구는 경제적인 에너지량으로 높은 효율의 세정을 보일 수 있는 적절한 유속의 정당성 평가를 목적으로 한다. 정삼투 공정 막오염 실험을 8.54 cm/s 순환 유속으로 유지하고 세 가지 세정유속으로 회복률과 SEC(specific energy consumption) 비교 평가하였다. 이 실험의 결과로 2배속 세정이 3배속 세정의 수투과도 회복률 만큼의 높은 효율을 보 이는 동시에, 2배속 세정이 높은 세정효율 및 경제적인 SEC를 보이는 적절한 유속이라는 것을 확인하였다.

In this study, fire and evacuation safety of environmental energy facilities using fire and evacuation simulation was examined as part of performance-oriented design. The worst-case fire scenarios in which fire-fighting facilities such as sprinkler fire extinguishing and smoke control systems are not working, and the FDS analyzes the visibility, temperature distribution, and carbon monoxide concentration distribution through FDS. The safety was examined. As a result, it was proved that evacuation could limit the visibility, temperature, and carbon monoxide concentration in a smooth range, based on the safety standards set by relevant laws. In other words, it was possible to verify the safety of fire and evacuation for environmental energy facilities where a large amount of combustibles and fires coexist.

A flexible piezoelectric energy harvester(f-PEH) that converts tiny mechanical and vibrational energy resources into electric signals without any restraints is drawing attention as a self-powered source to operate flexible electronic systems. In particular, the nanocomposites-based f-PEHs fabricated by a simple and low-cost spin-coating method show a mechanically stable and high output performance compared to only piezoelectric polymers or perovskite thin films. Here, the non-piezoelectric polymer matrix of the nanocomposite-based f-PEH is replaced by a P(VDF-TrFE) piezoelectric polymer to improve the output performance generated from the f-PEH. The piezoelectric hybrid nanocomposite is produced by distributing the perovskite PZT nanoparticles inside the piezoelectric elastomer; subsequently, the piezoelectric hybrid material is spin-coated onto a thin metal substrate to achieve a nanocomposite-based f-PEH. A fabricated energy device after a two-step poling process shows a maximum output voltage of 9.4 V and a current of 160 nA under repeated mechanical bending. Finite element analysis(FEA) simulation results support the experimental results.

목 적：치아교정용 보철장치를 부착한 환자의 MRI 검사는 꾸준히 시행돼 오고 있다. 그러나 MRI 검사에서의 안전성에 대한 입증은 명확히 이루어지지 않고 있다. 이에 본 논문은 3.0T MRI에서의 자기장과 RF에 의한 치아교정용 보철장치와의 상호작용을 실제 임상 조건으로 실험하여 안전성을 입증하고자 한다. 대상 및 방법：3.0T MRI 장치와 광섬유 온도 측정계, 온도 측정용액, 치아교정용 보철장치를 사용하였으며, 자장에 의한 왜곡 실험은 편향각과 토크 측정 장치를 사용하여 측정하였으며, RF에 의한 발열 온도 측정은 wire와 bracket을 결합한 후 온도 측정용액에 담그고, 광섬유 온도계의 온도 센서를 치아교정용 보철장치와 그 주변부에 설치한 후 실제 임상 조건으로 실험하였다. 결 과：고정 자기장에 의한 편향각 측정에서 bracket은 5회 측정 평균 19.88ﾟ, Ni-Ti wire는 1.96ﾟ, stainless steel wire는 119ﾟ로 측정되었으며, torque 실험에서는 bracket과 Ni-Ti wire는 0점으로 no torque이었으며, stainless steel wire는 +4점으로 very strong torque로 측정되었다. RF 주파수인가로 인한 온도 변화는 Ni-Ti wire bracket에서는 임 상 조건 실험 시작 전 target 온도 21.8ﾟC에서 약 23분 34초간 측정하였을 때 22.2ﾟC로 약 0.4ﾟC 상승하였으며, 주변부 온도는 21.4ﾟC에서 22.4ﾟC로 약 1ﾟC 상승하였고, stainless steel bracket에서는 target 온도 23.5ﾟC에서 23.9ﾟC로 0.4 ﾟC, 주변부 온도는 23.4ﾟC에서 23.3ﾟC로 측정되었다. 결 론：본 연구의 실험을 통해 치아교정용 보철장치의 RF에 의한 발열 현상에 따른 온도 변화는 크지 않고, 주 자기장에 의한 영향은 치아교정 보철장치의 자화 감수성에 따라 크게 차이가 남으로써 주 자기장에 의한 치아교정용 보철장치의 치아 내 위치 변화가 발생할 가능성이 있음을 확인할 수 있었다.

Lead free (Ba0.7Ca0.3) TiO3 thick films with nano-sized grains are prepared using an aerosol deposition (AD) method at room temperature. The crystallinity of the AD thick films is enhanced by a post annealing process. Contrary to the sharp phase transition of bulk ceramics that has been reported, AD films show broad phase transition behaviors due to the nanosized grains. The polarization-electric hysteresis loop of annealed AD film shows ferroelectric behaviors. With an increase in annealing temperature, the saturation polarization increases because of an increase in crystallinity. However, the remnant polarization and cohesive field are not affected by the annealing temperature. BCT AD thick films annealed at 700 ℃/2h have an energy density of 1.84 J/cm3 and a charge-discharge efficiency of 69.9%, which is much higher than those of bulk ceramic with the same composition. The higher energy storage properties are likely due to the increase in the breakdown field from a large number of grain boundaries of nano-sized grains.

This study aimed to investigate the effect of using corn flakes, produced by pressurized steam chamber, on nutrient disappearance rate and energy value in three Hanwoo and three Holstein cows, implanted with a ruminal fistula. Corn flakes were categorized in 2 groups based on the chamber type: control (corn flakes produced using a steam chamber) and treatment (corn flakes produced using a pressurized steam chamber). Dry matter (DM) disappearance rate was 5.17% higher in treatment than in control (p<0.01). Starch disappearance rate was also higher in the treatment than in the control (p<0.01). Nitrogen free extract (NFE) and non-fiber carbohydrate (NFC) disappearance rates were 6.08 and 5.71% higher in treatment compared to control, respectively (p<0.01). In comparison by breed and incubation time, DM, starch, NFE, and NFC disappearance rates were higher in treatment than in control. The mean total digestible nutrients (TDN) was higher in treatment than in control (p<0.05). In comparison between Hanwoo and Holstein, TDN of corn flakes was slightly but not significantly higher in Holstein than in Hanwoo. Thus, these results indicate that the use of the pressurized steam chamber is recommended to increase the nutrient (starch, NFE, NFC etc.) disappearance rate and TDN.

PURPOSES : A geo-grid pavement, e.g., a stress-absorbing membrane interlayer (SAMI), can be applied to an asphalt-overlay method on the existing surface-pavement layer for pavement maintenance related to reflection cracking. Reflection cracking can occur when a crack in the existing surface layer influences the overlay pavement. It can reduce the pavement life cycle and adversely affect traffic safety. Moreover, a failed overlay can reduce the economic value. In this regard, the objective of this study is to evaluate the bonding properties between the rigid pavement and a SAMI by using the direct shear test and the pull-off test. The predicted fractural energy functions with the shear stress were determined from a numerical analysis of the moving average method and the polynomial regression method. METHODS : In this research, the shear and pull-off tests were performed to evaluate the properties of mixtures constructed using no interlayer, a tack-coat, and SAMI with fabric and without fabric. The lower mixture parts (describing the existing pavement) were mixed using the 25-40-8 joint cement-concrete standard. The overlay layer was constructed especially using polymer-modified stone mastic asphalt (SMA) pavement. It was composed of an SMA aggregate gradation and applied as the modified agent. The sixth polynomial regression equation and the general moving average method were utilized to estimate the interlayer shear strength. These numerical analysis methods were also used to determine the predictive models for estimating the fracture energy. RESULTS: From the direct shear test and the pull-off test results, the mixture bonded using the tack-coat (applied as the interlayer between the overlay layer and the jointed cement concrete) had the strongest shear resistance and bonding strength. In contrast, the SAMI pavement without fiber has a strong need for fractural energy at failure. CONCLUSIONS : The effects of site-reflection cracking can be determined using the same tests on cored specimens. Further, an empiricalmechanical pavement-design analysis using the finite-element method (FEM) must be done to understand the appropriate SAMI application. In this regard, the FEM application analysis and bonding property tests using cored specimens from public roads will be conducted in further research.

The boundary reaction method(BRM) is a substructure time domain method, it removes global iterations between frequency and time domain analyses commonly required in the hybrid approaches, so that it operates as a two-step uncoupled method. The BRM offers a two-step method as follows: (1) the calculation of boundary reaction forces in the frequency domain on an interface of linear and nonlinear regions, (2) solving the wave radiation problem subjected to the boundary reaction forces in the time domain. In the time domain analysis, the near-field soil is modeled to simulate the wave radiation problem. This paper evaluates the performance of the BRM according to modeling extent of near-field soil for the nonlinear SSI analysis of base-isolated NPP structure. For this purpose, parametric studies are performed using equivalent linear SSI problems. The accuracy of the BRM solution is evaluated by comparing the BRM solution with that of conventional SSI seismic technique. The numerical results show that the soil condition affects the modeling range of near-field soil for the BRM analysis as well as the size of the basemat. Finally, the BRM is applied for the nonlinear SSI analysis of a base-isolated NPP structure to demonstrate the accuracy and effectiveness of the method.

Gas hydrate desalination process is based on a liquid to solid (Gas Hydrate, GH) phase change followed by a physical process to separate the GH from the remaining salty water. The GH based desalination process show 60.5-90% of salt rejection, post treatment like reverse osmosis (RO) process is needed to finally meet the product water quality. In this study, the energy consumption of the GH and RO hybrid system was investigated. The energy consumption of the GH process is based on the cooling and heating of seawater and the heat of GH formation reaction while RO energy consumption is calculated using the product of pressure and flow rate of high pressure pumps used in the process. The relation between minimum energy consumption of RO process and RO recovery depending on GH salt rejection, and (2) energy consumption of electric based GH process can be calculated from the simulation. As a result, energy consumption of GH-RO hybrid system and conventional seawater RO process (with/without enregy recovery device) is compared. Since the energy consumption of GH process is too high, other solution used seawater heat and heat exchanger instead of electric energy is suggested.

본 연구에서는 LED 광원에 대하여 재실자의 업무 효율성과 에너지 저감 효과를 알아보기 위한 실험을 실시하 였다. 이를 위해 LED 광원의 특성인 펄 스 폭변조(PWM, pulse width modulation)와 조도(lux)를 제어하여 총 9가 지의 다양한 조명환경을 구성하였다. LED 조명의 펄스변조 비율은 각각 R:G:B=1:1:1, R:G:B=4:1:5, R:G:B=8:7:7 으로 하였으며, 조도는 각각 400 lx, 700 lx, 1000 lx 으로 설정하였다. 또한, 실내환경은 온도 20∼24℃, 습도 50∼ 60%, 착의량 1 clo 로 설정하였다. 각각의 주어진 9개의 조명환경에서 업무 효율성과 에너지 소비에 대해 분석하 였다. 업무 효율성 분석을 위해 오류검색수정 작업을 실시하였으며, 에너지 소비 분석을 위해 각 조명환경에서 누적 소비전력을 측정하였다. 제안한 조명환경을 통해 실험한 결과, 업무 효율성은 400 lx 보다 700 lx 이상에서 정확도 및 소요시간의 효율이 좋았으며, 소요시간의 경우 제안한 펄스변조 R:G:B=8:7:7 에서 가장 좋은 효율을 나타냈다. 또한, 각각의 조도에 대한 소비전력은 펄스변조 R:G:B=8:7:7 > RGB=1:1:1 > R:G:B=4:1:5의 순으로 낮게 나타났다. 따라서, 본 논문에서 제안한 펄스 폭 변조 효과가 업무효율성 및 에너지 저감에 영향을 미치는 것을 확인할 수 있었다.