Outdoor storage fires have a significant impact on the surrounding environment, including adjacent storage facilities and buildings. Therefore, it is essential to review and manage the fire impact to minimize damage to human life and property on the outdoor storage fires. In this study, the heat release rate and radiant heat flux were simulated according to the fire time, wind veolcity, and presence or absence of water spray equipment in an outdoor storage facility fire, and the fire impact was analyzed. The outdoor storage was designed to simulate two scenarios on the outdoor storage fires containing gasoline, and FDS was used for fire simulation. As a results, when the water spray facility was not operating and the wind velocity was 5 m/s, the maximum radiant heat flux was 24.80 kW/m2, which exceeded the limit radiant heat flux of 20 kW/m2. When the water spray facility was operating and the wind veolcity was 10 m/s, the maximum radiant heat flux was 18.77 kW/m2, which did not exceed the limit radiant heat flux, indicating that the fire impact on adjacent storage facilities was relatively small.

본 연구에서는 인디안구스베리(암라), 찔레나무, 쏘팔메토열매를 5:1:1 비율로 Complex하고 추 출하여 0%, 0.5%, 2.5%, 12.5%, 100%의 NF Complex를 제조하였다. 제조한 NF Complex로 탈색한 시 료 모발에 도포 후 손상된 모발과 비교 · 분석하였다. 개선 효과를 확인하기 위해 인장강도, 광택, 흡광도, 명도를 측정하였다. 측정 결과 인장강도는 증가하였다. 광택은 함량이 100%는 감소하고 나머지 함량은 증 가하였다. 흡광도는 손상모와 대조군과의 차이가 있어 개선 효과가 있는 것으로 보인다. 명도는 변화는 있 으나 미미하였다. NF Complex의 평균값은 유의미한 차이가 있음을 확인하였으며 추후 다양한 추출방법 및 혼합 비율에 따른 연구가 필요하다고 판단된다.

Human and material damage can be reduced if the risk is evaluated by engineering analysis of fire combustion products, smoke concentration, and smoke movement speed in the event of a fire in apartment houses and officetels. In this study, a lot of research on related safety evaluation in the basement needs to be studied and reflected in design, so experimental research was conducted to analyze the flow of smoke through computer simulation and provide analysis data through evacuation safety evaluation. First of all, the five-story underground parking lot subject to simulation has a large floor area, which is advantageous for improving evacuation safety performance, but it uses temperature detectors to increase detection time and fire spread speed. Second, it was analyzed that the evacuation time at all evacuation ports did not exceed the evacuation time, and as the time from the start of evacuation to the evacuation time was 216.9% compared to the travel time, it was evaluated that the safety performance of the evacuation was secured. Third, the above simulation results are a comprehensive safety evaluation based on the non-operation of fire extinguishing facilities in the fire room to increase safety, which means that smoother evacuation safety performance can be secured by linking fire extinguishing facilities.

In electric vehicles, the core is a secondary cell battery. Raw material is pulverized by the grinding disc in the Classifier Separator Mill (CSM) and rises through the Classifier Wheel. Both require characteristics to withstand high-speed rotation, including abrasion, corrosion, and shock. Our study analyzes the impact of RPM and heat source on temperature, convergence, and durability. In conclusion, high heat increases flow, while high RPM reduces the maximum temperature but may harm durability. Proper RPM settings enhance durability.

The purpose of this study is to present the direction of the plan to transform the residential complex into a space that can provide an open residential environment that can lead to social communication and exchange without being closed to the urban residential environment, especially in the apartment complex environment, which is becoming more dense. As a result of the Openness analysis of the ‘Codan Shinonome Canal Court’, the overall accessibility was good in terms of space utilization, and the openness was low in terms of the spatial composition, which is a physical environment due to the dense block type. When looking at the overall openness of the Codan Sinonome complex in terms of analysis by block, the corrected openness index (C.O.I) for all six blocks was 0.245, the corrected accessibility index (C.A.I) was 1.447 and the openness composite index (O.C.I) was assessed at 1.692. This was due to the formation of high-density block-type urban dwellings and the introduction of S-shaped streets and the layout of low-rise urban support facilities and commercial facilities. The Codan Sinonome Canal Court, which is considered an “open city residence,” quantitatively confirmed that it embodies macro-space structure and human-scale space environment even in high-precision environments.

본 연구는 다시마 추출물을 첨가한 모질 개선 제형제를 제조하여 손상된 모발에 도포하여 손상 모발의 개선 효과를 알아보고자 하였다. 실험재료는 다시마 추출물 함량을 0 g, 2 g 4 g, 6 g 으로 다르게 하여 펌베이스제에 첨가하여 제형제를 제조하였다. 제조한 제형제로 8레벨로 탈색한 시료 모발에 도포 전과 후를 측정하여 비교 분석하였다. 측정방법은 모질 개선 효과를 알기 위해 인장강도, 메틸렌블루를 이용한 흡광도, 광택을 측정하였다. 연구결과의 신뢰성을 위해 통계분석을 하였다. 연구결과로 인장강도 측정결과는 8레벨에 4 g 과 6 g 을 함유한 제형제로 도포한 시료의 인장강도가 증가함을 알 수 있었다. 메틸렌블루를 이용한 흡광도 분석결과 모든 시료의 도포 전, 후의 변화는 도포 후의 값이 감소함을 알 수 있었다. 광택 측정결과는 모든 시료에서 큰 차이가 없음을 알 수 있었다. 결론은 다시마 추출물이 손상된 모발에 개선 효과가 있는 것을 알 수 있었다. 차후 다양한 추출물의 종류와 연구방법으로 손상모발에 개선효과가 있는지 연구가 필요하다.

본 연구는 밀크씨슬 오일을 첨가한 모질 개선 제형제를 제조하여 손상된 모발에 도포하여 모질 개선 효과를 알아보고자 하였다. 밀크씨슬 오일 함량을 0 g, 1 g 2 g, 3 g 으로 다르게 하여 제형제를 제조하였다. 제조한 제형제로 탈색한 시료 모발에 도포 후 열처리와 자연방치를 한 후에 시료 별로 도포 전과 후를 측정하여 비교 분석하였다. 모질 개선 효과를 알기 위해 인장강도, 메틸렌블루를 이용한 흡광도, 광택을 측정하였고 하였다. 모질 개선 효과를 알기위한 인장강도 측정결과는 7레벨과 9레벨 모든 시료의 인장 강도가 증가함을 알 수 있었다. 메틸렌블루를 이용한 흡광도 분석결과 도포 전, 후의 변화는 도포 후의 값이 감소함을 알 수 있었다. 광택 측정결과는 모든 시료에서 큰 차이가 없음을 알 수 있었다. 밀크씨슬 오일 이 손상된 모발에 모질 개선 효과가 있는 것을 알 수 있었다. 차후 다양한 오일 종류와 연구방법으로 모질 개선 연구가 필요하다.

The purpose of this study is to identify the leading price between Jeju and Wando’s oliver flounder producer price and to analyze the dynamic effect of the regional producer price using the panel VAR model. In the process of analysis, it was confirmed that there are unit roots in the monthly data of Jeju and Wando’s oliver flounder producer price. So, in order to avoid spurious regression, the rate change of producer price which carries out log difference was used in the analysis. As a result of the analysis, first, the panel Granger causality test showed that the influence of the change rate of producer price in oliver flounder in Jeju was slightly larger than that in Wando, but it was found that each region all leads the change rate of the producer price in oliver flounder. Second, the panel VAR estimation showed that the rate change of producer price in Jeju and Wando a month ago had a statistically significant effect on the change rate of producer price of each region. Third, the impulse response analysis indicated that other regions are affected a little more than the same region in case of the occurrence of the impact on the error terms of the change rate of produce price in Jeju and Wando oliver flounder. Fourth, the variance decomposition analysis showed that the change rate of producer price in the two regions was higher explained by Jeju compared to Wando. In conclusion, it is expected that the above results can not only be useful as basic data for the stabilization of oliver flounder producer price and the establishment of policies for easing volatility but can also help the oliver flounder industry operate its business.

The public relations room of the waste disposal facility is a space that can be visited by a large number of unevaluated personnel. Therefore, it is essential to design against fire, and research on fire and evacuation is essential. In this study, in order to evaluate the safety of the occupants in the event of fire and evacuation based on the life safety standards of occupants, the increase in risk due to heat, visible distance, and toxic gases on a plane 1.8m from the floor, which is the limit of breathing of the evacuee, over time. It was analyzed by location. As a result, the RSET of the P-01 exit was 93.0 seconds and the ASET was 272.6 seconds, the RSET of the P-02 exit was 45.8 seconds, the ASET was 147.7 seconds, the RSET of the P-03 exit was 106 seconds, and the ASET was 182.9 seconds.

Industrial facilities need design to predict and reduce noise from design to prevent and reduce noise. The purpose of this study is to predict worker's environment and evaluate safety by analyzing noise inside underground blower room and air compressor room with fluid machinery in waste facility. This waste incineration facility was analyzed based on the ground floor, ground floor blower chamber, and air compressor chamber. The results of SPL(Sound Pressure Level) analysis at 1.5m away, which are frequently used to measure the SPL as a noise source, are as follows. SPL of basement level: 46.80[dB], SPL of ground layer: 48.57[dB]. As a result, it was expected that the noise level would be considerably lower than the 8 hours 50[dB] noise exposure per day.

Sludge incineration facilities are socially recognized as a hate facility. Therefore, a careful deodorization plan must be established. Therefore, the incineration facility must conduct research on odor ventilation. In this study, a odor diffusion simulation in an incineration facility was conducted and analyzed. In particular, research was carried out on carry-in rooms, pre-treatment rooms, and storage facilities for crops, which are expected to rapidly spread odor. As a result, ammonia 1.62, hydrogen sulfide 0.63, and acetaldehyde 0.73 were found in the transfer room. In addition, pretreatment rooms and stencil storage facilities were found to be lower than regulatory standards.

The basalt fiber is expected to become a trend for industrial fibers as they have better properties of heat-resistant, non-combustion, absorbent, soundproof, moistureproof, lightweight, corrosion resistant, and high strength properties. Also, the fiber is found to be non-toxic and harmless to the human body. Therefore, in this study, we analyzed the chemical and mineral compositions of powdered sludge of basalt produced at seven sites on Jeju Island for the development of fire resistance insulating material for a building. The results showed that the basalt stone sludge is made from only sodium calcium aluminum silicate and ferridioside components unlike the basalt rock.

In this study, fire and evacuation safety of environmental energy facilities using fire and evacuation simulation was examined as part of performance-oriented design. The worst-case fire scenarios in which fire-fighting facilities such as sprinkler fire extinguishing and smoke control systems are not working, and the FDS analyzes the visibility, temperature distribution, and carbon monoxide concentration distribution through FDS. The safety was examined. As a result, it was proved that evacuation could limit the visibility, temperature, and carbon monoxide concentration in a smooth range, based on the safety standards set by relevant laws. In other words, it was possible to verify the safety of fire and evacuation for environmental energy facilities where a large amount of combustibles and fires coexist.

When the heat flux on the heating surface following changing heat condition in the boiling heat transfer system exceeds critical heat flux, the critical heat flux phenomenon is going over to immediately the film boiling area and then it is occurred the physical destruction phenomenon of various heat transfer systems. In order to maximize the safe operation and performance of the heat transfer system, it is essential to improve the CHF(Critical Heat Flux) of the system. Therefore, we have analysis the effect of improving CHF and characteristics of heat transfer following the nanoparticle coating thickness. As the results, copper nanocoating time are increased to CHF, and in case of nano-coatings are increased spray-deposited coating times more than in the fure water; copper nanopowder is increased up to 6.40%. The boiling heat transfer coefficients of the pure water are increased up to 5.79% respectively. Also, the contact angle is decreased and surface roughness is increased when nano-coating time is increasingly going up.

This study is analyzed combustion phenomena based on the environmental energy facility incinerator. It is assumed that combustible components of waste are composed of carbon and hydrogen, and the combustion process of fuel is by setting as multi-component / multistage reaction. As the combustion chamber is burned, the high temperature environment is achieved, also the heat transfer accompanied by the turbulent flow and the generation of NOx, a pollutant, are interpreted to predict the thermal and fluid characteristics and pollution emissions of the grate incinerator. As the result of internal flow analysis, the slow flow around the ash chute and the mixing effect due to the complicated turbulence around the combustion chamber were predicted to show excellent performance. It is shown to the internal average temperature was about 1024°C, around the about 1000°C homogeneous temperature distribution. Due to the sudden temperature decrease in the boiler, the flue gas temperature at the outlet was estimated to be about 220 ℃.

This paper is a study to estimate the noise generated by fluid around each machine in the basement and basement facilities that accept major noise factor, pump fluid mechanical equipment installed to evaluate the impact on the real working environment. In particular, the review of the reliability of complementary information and reliability predict the natural frequency for generating a maximum strain when the vibration analysis, and intended to ensure that the design to avoid a natural frequency of the structure, on the basis of the this analysis result to the subject a real building.

In this study, we investigated to the heat transfer performance of coating nano-structure with various shapes and patterns on the heat transfer surface. As a result of the measurement of the 3D nano shape, it was confirmed that the roughness generally increases when the adhesive is sprayed on the coating surface and finished durability experiment. In the case of TEOS adhesive, the roughness increased by 0.074 ㎛, 0.012 ㎛ and 0.015 ㎛, and the contact angle decreased 12.64°, 1.31°, 9.84° at the coating time of 120 seconds, 180 seconds and 240 seconds, respectively. In the case of PVA adhesive, the roughness increased by 0.069 ㎛, 0.056 ㎛ and 0.03 ㎛, and the contact angle decreased 2.85°, 4.82°, 6.96° at the coating time of 120 seconds, 180 seconds and 240 seconds, respectively. In the case of DGEBF adhesive, the roughness increased by 0.042 ㎛, 0.053 ㎛ and 0 ㎛, and the contact angle decreased 0.81° at the coating time of 120 seconds, increased 4.82°, 6.96° at the coating time of 180 seconds and 240 seconds, respectively. As a result, the durability tends to decrease as more nano-structures are deposited, and 3D nano shapes, contact angles and SEM photographs showed that the performance of the PVA adhesive was superior among the three adhesives.