Fluorine-doped tin oxide (FTO) has been used as a representative transparent conductive oxide (TCO) in various optoelectronic applications, including light emitting diodes, solar cells, photo-detectors, and electrochromic devices. The FTO plays an important role in providing electron transfer between active layers and external circuits while maintaining high transmittance in the devices. Herein, we report the effects of substrate rotation speed on the electrical and optical properties of FTO films during ultrasonic spray pyrolysis deposition (USPD). The substrate rotation speeds were adjusted to 2, 6, 10, and 14 rpm. As the substrate rotation speed increased from 2 to 14 rpm, the FTO films exhibited different film morphologies, including crystallite size, surface roughness, crystal texture, and film thickness. This FTO film engineering can be attributed to the variable nucleation and growth behaviors of FTO crystallites according to substrate rotation speeds during USPD. Among the FTO films with different substrate rotation speeds, the FTO film fabricated at 6 rpm showed the best optimized TCO characteristics when considering both electrical (sheet resistance of 13.73 Ω/□) and optical (average transmittance of 86.76 % at 400~700 nm) properties with a figure of merit (0.018 Ω-1).

Recently, air pollution from fossil fuels is at a serious level, and the IMO proposes to reduce greenhouse gas emissions by about 70% by 2050, and controls greenhouse gas emissions by applying the energy efficiency disign index(EEDI) to each ship type. In this study, the marine fuel oil viscosity of MGO, MDO, HFO and CGO according to the temperature change was compared and measured and the difference was analyzed. As a result, the viscosity of CGO was 3.32mPa·s, which was almost similar to MGO(3.40mPa·s) and MDO(3.51mPa·s) so it was judged that it could be used as a marine fuel, and it was found that there was a significant difference with HFO at P<0.01 there was.

In this study, ultrasonic spray pyrolysis combined with salt-assisted decomposition, a process that adds sodium nitrate (NaNO3) into a titanium precursor solution, is used to synthesize nanosized titanium dioxide (TiO2) particles. The added NaNO3 prevents the agglomeration of the primary nanoparticles in the pyrolysis process. The nanoparticles are obtained after a washing process, removing NaNO3 and NaF from the secondary particles, which consist of the salts and TiO2 nanoparticles. The effects of pyrolysis temperature on the size, crystallographic characteristics, and bandgap energy of the synthesized nanoparticles are systematically investigated. The synthesized TiO2 nanoparticles have a size of approximately 2–10 nm a bandgap energy of 3.1–3.25 eV, depending on the synthetic temperature. These differences in properties affect the photocatalytic activities of the synthesized TiO2 nanoparticles.

Li-incorporated ZnO thin films were deposited by using ultrasonic-assisted spray pyrolysis deposition (SPD) system. To investigate the effect of Li-incorporation on the performance of ZnO thin films, the structural, electrical, and optical properites of the ZnO thin films were analyzed by means of X-ray diffraction (XRD), field-emssion scanning electron microscopy (FE-SEM), Hall effect measurement, and UV-Vis spectrophotometry with variation of the Li concentraion in the ZnO sources. Without incorporation of Li element, the ZnO surface showed large spiral domains. As the Li content increases, the size of spiral domains decreased gradually, and finally formed mixed small grain and one-dimensional nanorod-like structures on the surface. This morphological evolution was explained based on an anti-surfactant effect of Li atoms on the ZnO growth surface. In addition, the Li-incorporation changed the optical and electrical properties of the ZnO thin films by modifying the crystalline defect structures by doping effects.

본 연구에서는 자원내 포함된 역청의 경질화 과정에서 배출 및 회수되는 가스상 물질 및 고체상 물질을 활용하기 위한 기초 성상이 조사되었다. 이를 위하여 열분해 온도 별 역청성 오일의 전환에 대한 열분해반응 기초특성이 조사되었다. 또한 실험실 규모의 고정층 반응기를 이용하여 반응온도에 따른 가스 및 고체상 분산물의 특성을 조사하였다. 그 결과 550 ℃에서 약 17%의 오일 수율을 얻었으며, 부산물로는 CH4, CaCO3 및 CaO를 회수할 수 있음을 확인하였다.

Inorganic phosphors based on ZrO2:Eu3+ nanoparticles were synthesized by a salt-assisted ultrasonic spray pyrolysis process that is suitable for industrially-scalable production because of its continuous nature and because it does not require expensive precursors, long reaction time, physical templates or surfactant. This facile process results in the formation of tiny, highly crystalline spherical nanoparticles without hard agglomeration. The powder X-ray diffraction patterns of the ZrO2:Eu3+ (1-20 mol%) confirmed the body centered tetragonal phase. The average particle size, estimated from the Scherrer equation and from TEM images, was found to be approximately 11 nm. Photoluminescence (PL) emission was recorded under 266 nm excitation and shows an intense emission peak at 607 nm, along with other emission peaks at 580, 592 and 632 nm which are indicated in red.

바이오오일은 고품질 화학물질로 이용이 가능하며 차세대 탄화수소 연료와 석유정제업 공급 원료로 사용할 수 있기 때문에 촉망받는 신재생에너지의 하나로 상당한 관심을 받고 있다. 또한 제올라이트는 급속열분해 과정에서 크래킹 반응을 효과적으로 촉진시켜 탈산소 반응을 증가 시키고 탄화수소가 많은 안정된 바이오오일을 만든다. 그래서 본 연구에서는 백합나무 바이오오일 품질개선을 위해 촉매열분해(Control, Blackcoal, Whitecoal, ZeoliteY 및 ZSM-5)를 적용하여 특성을 조사하였다. 바이오오일의 특성 변화를 알아보기 위하여 0.3～1.4 mm 크기의 백합나무 시료 500 g을 465℃에서 1.6초 동안 촉매열분해하여 바이오오일을 제조하였다. 촉매 조건 상태에서 바이오오일의 수율은 Control(54.0%)과 비교하여 Blackcoal(56.2%)를 제외하면, Whitecoal(53.5%), ZeoliteY (51.4%), 및 ZSM-5(52.0%)로 모두 감소했다. 수분 함량이 Control(37.4%)에서 촉매 처리후 37.4~45.2%로 증가함에 따라 발열량((High heating value)은 감소했다. 그러나 다른 다른 바이오오일 특성은 개선되었다. 촉매 적용 결과 바이오오일의 회분과 전산가(TAN)가 감소했고, 특히 수송연료로 중요한 특성인 점도는 Control cP(6,933) 에서 2,578 ~ 4,627 cP로 감소했다. 또한 ZeoliteY는 방향족탄화수소를 생산하고 점도를 개선시키는데 가장 효과적이였다.

본 연구는 폴리스타렌(PS) 수지의 유화공정 효율성 향상을 위해 저온열분해 회분식 반응기를 이용하여, 단일 PS 수지와 Co 및 Mo 촉매를 각각 첨가한 PS 수지를 반응온도(425, 450, 475℃), 반응 시간(20~80분, 15분 간격), 촉매 농도변화에 따른 PS수지의 액화생성물 전환율을 측정하였다. 최적의 열분해 조건은 반응온도 450℃, 반응시간 35분으로 판단되며, 전환된 액화생성물의 주요 성분은 GC/MS 분석결과 스타이렌 및 벤젠유도체가 대부분으로 나타났다. 생성물은 산업통상자원부에서 고시 한 증류성상 온도에 따라 가스, 가솔린, 등유, 경유, 중유로 분류하여 그 수율을 측정하였다. 그리고 45 0℃ 반응온도에서 촉매 사용에 따른 전환율은 Co 촉매 > Mo 촉매 > 무촉매 순이었으며, 생성물 중 가 스, 등유, 경유수율은 Mo 촉매, 가솔린은 무촉매, 중유는 Co 촉매에서 우수한 것으로 나타났다. Co 및 Mo 촉매 혼합 농도별 전환율 및 열분해 생성물 수율은 Co 촉매 100% 사용 시 가장 우수한 것으로 판 단된다.

Fluorine-doped tin oxide (FTO) nanoparticles have been successfully synthesized using ultrasonic spray pyrolysis. The morphologies, crystal structures, chemical bonding states, and electrochemical properties of the nanoparticles are investigated. The FTO nanoparticles show uniform morphology and size distribution in the range of 6-10 nm. The FTO nanoparticles exhibit excellent electrochemical performance with high discharge specific capacity and good cycling stability (620mA h g−1 capacity retention up to 50 cycles), as well as excellent high-rate performance (250 mA h g−1 at 700mAg−1) compared to that of commercial SnO2. The improved electrochemical performance can be explained by two main effects. First, the excellent cycling stability with high discharge capacity is attributed to the nano-sized FTO particles, which are related to the increased electrochemical active area between the electrode and electrolyte. Second, the superb high-rate performance and the excellent cycling stability are ascribed to the increased electrical conductivity, which results from the introduction of fluorine doping in SnO2. This noble electrode structure can provide powerful potential anode materials for high-performance lithiumion batteries.

Hydrogen is considered a potential future energy source. Among other applications of hydrogen, hydrogen-rich water is emerging as a new health care product in industrial areas. Water electrolysis is typically used to generate a hydrogen rich water system. We annealed 10AA carbon paper in air to use it as an electrode of a hydrogen rich water generator. Driven by annealing, structural changes of the carbon paper were identified by secondary electron microscope analysis. Depending on the various annealing temperatures, changes of the hydrophilic characteristics were demonstrated. The crystal structures of pristine and heat-treated carbon paper were characterized by X-ray diffraction. Improvement of the efficiency of the electrochemical oxygen evolution reaction was measured via linear voltammetry. The optimized annealing temperature of 10AA carbon paper showed the possibility of using this material as an effective hydrogen rich water generator.

본 연구는 폴리프로필렌(PP) 수지의 Co 및 Mo 촉매에 의한 반응시간과 농도변화에 따른 저온열분해 액화특성을 파악하고자 회분식 반응기를 이용하여 특정 온도(425, 450, 475℃)에서의 전환율을 측정하였다. 열분해 시간은 20~80분으로 설정하였고 생성물은 산업통상자원부에서 고시한 증류성상 온도에 따라 가스, 가솔린, 등유, 경유, 중유로 분류하였다. 그리고 450℃ 반응온도에서 촉매 사용에 따른 전환율은 모든 반응시간에 있어 Mo 촉매 > Co 촉매 > 무촉매 순이었다. Co 및 Mo 촉매 농도별 PP 전환율 및 열분해 생성물 수율은 Co:Mo=50:50 혼합시 가장 우수한 것으로 나타났다.

Silicon carbide(SiC) layer is particularly important tri-isotropic (TRISO) coating layers because it acts as a miniature pressure vessel and a diffusion barrier to gaseous and metallic fission products in the TRISO coated particle. The high temperature deposition of SiC layer normally performed at 1500-1650˚C has a negative effect on the property of IPyC layer by increasing its anisotropy. To investigate the feasibility of lower temperature SiC deposition, the influence of deposition temperature on the property of SiC layer are examined in this study. While the SiC layer coated at 1500˚C obtains nearly stoichiometric composition, the composition of the SiC layer coated at 1300-1400˚C shows discrepancy from stoichiometric ratio(1:1). 3-7μm grain size of SiC layer coated at 1500˚C is decreased to sub-micrometer (＜ 1μm) -2μm grain size when coated at 1400˚C, and further decreased to nano grain size when coated at 1300-1350˚C. Moreover, the high density of SiC layer (≥3.19g/cm3) which is easily obtained at 1500˚C coating is difficult to achieve at lower temperature owing to nano size pores. the density is remarkably decreased with decreasing SiC deposition temperature.

Much research into fuel cells operating at a temperature below 800℃. is being performed. There are sig-nificant efforts to replace the yttria-stabilized zirconia electrolyte with a doped ceria electrolyte that has high ionic con-ductivity even at a lower temperature. Even if the doped ceria electrolyte has high ionic conductivity, it also shows highelectronic conductivity in a reducing environment, therefore, when used as a solid electrolyte of a fuel cell, the power-generation efficiency and mechanical properties of the fuel cell may be degraded. In this study, gadolinium-doped ceriananopowder with Al2O3 and Mn2O3 as a reinforcing and electron trapping agents were synthesized by ultrasonic pyrol-ysis process. After firing, their microstructure and mechanical and electrical properties were investigated and comparedwith those of pure gadolinium-doped ceria specimen.

Silicon nanoparticle is a promising material for electronic devices, photovoltaics, and biological applications. Here, we synthesize silicon nanoparticles via CO2 laser pyrolysis and study the hydrogen flow effects on the characteristics of silicon nanoparticles using high resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), and UV-Vis-NIR spectrophotometry. In CO2 laser pyrolysis, used to synthesize the silicon nanoparticles, the wavelength of the CO2 laser matches the absorption cross section of silane. Silane absorbs the CO2 laser energy at a wavelength of 10.6μm. Therefore, the laser excites silane, dissociating it to Si radical. Finally, nucleation and growth of the Si radicals generates various silicon nanoparticle. In addition, researchers can introduce hydrogen gas into silane to control the characteristics of silicon nanoparticles. Changing the hydrogen flow rate affects the nanoparticle size and crystallinity of silicon nanoparticles. Specifically, a high hydrogen flow rate produces small silicon nanoparticles and induces low crystallinity. We attribute these characteristics to the low density of the Si precursor, high hydrogen passivation probability on the surface of the silicon nanoparticles, and low reaction temperature during the synthesis.

In case of domestic pyrolysis dry distillation gassification technology, it stays at the stage of its early introduction and development. Moreover, the companies possessed of this technology are limited to Japan and some countries in Europe, and domestic operative performance of this system is nominal, so there exist a lot of difficulties in securing its basic data. In addition, considering its operation and management, there happens a corrosion of metals by the production of corrosive gases in time of combustion of waste, and there arise a problem of occurrence of low temperature corrosion on exterior casing or gas ducts of a combustion chamber due to the high temperature corrosion around the burner of an incinerator, lowering the durability of an incinerator. Therefore, this study looked at the problems arising in time of incineration by understanding the characteristics of the pyrolysis dry distillation gassification incinerating facility, and did research on the improvement plan for durability of an incinerator for more economic, efficient waste incineration.

Hexagonal barium ferrite () nano-particles have been successfully fabricated by spraypylorysis process. precursor solutions were synthesized by self-assembly method. Diethyleneamine (DEA) surfactant was used to fabricate the micelle structure of Ba-DEA complex under various DEA concentrations. powders were synthesized with addition of Fe ions to Ba-DEA complex and then fabricated powders by spray-pyrolysis process at the temperature range of . The molar ratio of Ba/DEA and heat-treatment temperatures significantly affected the magnetic properties and morphology of powders. powders synthesized with Ba/DEA molar ratio of 1 and heat-treated at showed the coercive forces (iHc) of 4.2 kOe with average crystal size of about 100 nm.

To investigate the synergy effect on the pyrolysis of mixture of polyethylene(PE) and polystyrene(PS), the pyrolysis of PE, PS and the mixture of PE-PS was carried out in a batch reactor at the atmospheric pressure and 450℃. The pyrolysis time was from 20 to 80 mins. The liquid products formed during pyrolysis were classified into gas, gasoline, kerosene, gas oil and heavy oil according to the distillation temperatures based on the petroleum product quality standard of Korea Institute of Petroleum Quality. The analysis of the product oils by GC/MS showed that the new components produced by mixing were not detected. The synergy effect according to mixing of PE and PS did not also appear. The conversion and yield of mixtures were in proportion to the mixing ratio of sample.