In this study, a prefabricated buckling brace (PF-BRB) was proposed, and a test specimen was manufactured based on the design formula for the initial shape and structural performance tests were performed. As a result of the experiment, all standard performance requirements presented by KDS 41 17 00 and MOE 2021 were satisfied before and after replacement of the reinforcement module, and no fracture of the joint module occurred. As a result of the incremental load test, the physical properties showed a significant difference in the stiffness ratio after yielding under the compressive load of the envelope according to the experimental results. It is judged necessary to further analyze the physical properties according to the experimental results through finite element analysis in the future.

본 논문에서는 구조물의 좌굴 온도와 좌굴 형상을 제어하는 새로운 크기 최적화 방법에 대해서 소개한다. 구조적 안정성 관점에서 구조물의 좌굴 온도와 좌굴 형상을 예측하는 것은 중요한 주제 중 하나이다. 이를 공학적인 직관을 통해 예측하고 최적화된 구조 설계 를 하는 것은 너무나 어려운 과제이다. 이러한 한계점을 해결하기 위해 본 연구에서는 유한요소 시뮬레이션과 치수 최적 설계 방식의 조합을 제안한다. 구조물의 좌굴 온도와 좌굴 형상이 구조물의 두께에 영향을 받는다는 생각에서 착안해 설계 변수를 구조물의 노드 의 두께 값으로 설정했다. 좌굴 온도 값과 좌굴 형상을 목적 함수로 정해진 부피 값을 제약 조건으로 두었다. 치수 최적 설계를 통해 원 하는 좌굴 온도와 좌굴 형상을 유도하기 위한 최적의 두께 분포를 결정할 수 있다. 제안된 치수 최적 설계의 타당성은 본 논문의 다양 한 직사각형 복합 구조물 예제들을 사용해서 검증하였다.

This paper conducted a comparative analysis of the shear buckling characteristics of trapezoidal and sinusoidal corrugated steel plates considering of their initial imperfection. Initial imperfection refers to the state where the shape of the corrugated plate is initially not perfect. As such, an initially imperfect shape was assumed using the eigen buckling mode. To calculate the buckling stress of corrugated steel plates, the linear buckling analysis used a boundary condition which was applied to the plate buckling analysis. For the comparison of trapezoidal and sinusoidal corrugation, the shape parameters were assumed using the case where the length and slope of each corrugation were the same, and the initial imperfection was considered to be from 0.1% to 5% based on the length of the steel plate. Here, for the buckling analysis, ANSYS, a commercial FEA program, was used. From the results of buckling analysis, the effect of overall initial imperfection showed that the larger the initial imperfection, the lower the buckling stress. However, in the very thin model, interaction or local buckling was dominant in the perfect shape, and in this case, the buckling stress did not decrease. Besides, the sinusoidal model showed higher buckling stress than the trapezoidal one, and the two corrugation shapes decreased in a similar way.

The curved bridges shows very complicate behaviors compare to straight girders due to its initial curvature. Usually, the shear strength is investigated due to the aspect ratio(transverse stiffeners spacing/height of girder) and many researches have been conducted for the web shear strength for I-shaped curved girders with high aspect ratios(larger than 3). In this study, numerical studies are carried out and the results are compared with the current design practices. By the analyses, the maximum aspect ratio of a transversely stiffened web panel are suggested to revisits the validity of a limited imposed by Basler.

The circular hollow section is usually used for member of main frame to carry the external load in single layer lattice dome. But, the H-shaped section may be used for member of main frame since it is convenient for attaching roof panels. Single layer lattice domes have various buckling characteristics, such as the overall buckling, the member buckling, and nodal buckling. The purpose of this study is to compare buckling characteristics of single-layer lattice domes in which the H-shaped steel section as the existing domestically-produced structural steel is used as main frames to those of domes in which a circular hollow section is used as main frames.

The purpose of this paper is to study the buckling characteristics of elliptical latticed domes under conservative loading conditions. The latticed domes are usually designed in geometrically spherical shape. For this type of latticed domes, many researchers have researched and even the simplified estimation codes for the buckling load level have been available. However, geometrically elliptical latticed domes have been often constructed, and show different buckling characteristics following with geometrical parameters as rise-to-span ratio and so on. Therefore, it is necessary to investigate the general tendency of buckling characteristics of the elliptical latticed domes. In this paper, to find out some buckling characteristics of elliptical latticed domes, height, boundary configuration and gap are used as the shape coefficients. For each model with different parameters, the eigen values and the buckling loads are evaluated.

쉘형 구조물의 불안정 현상은 크게 뜀좌굴과 분기좌굴로 분류할 수 있다. 이들은 구조물의 형상특성, 특히 형상 초기불완전에 대해 매우 민감하게 반응한다. 본 연구에서는, 형상 초기불완전을 가진 쉘형 구조물의 불안정 거동을 파악하기 위해 양단이 힌지로 고정된 얕은 정현형 아치의 평형경로를 조사한다. 비선형 방정식을 얻기 위해 Galerkin법을 이용하였으며, 증분형 방정식으로의 변환은 섭동법을 이용하였다.

In this study, trapezoidal corrugate plate were subjected to cyclic loading under displacement control. And then, results from the experiment, the behavioral characteristics and mechanism of energy dissipation were investigated. This result were different to the cumulative size of energy dissipation capacity in load-displacement curve. Based on these results, Influence of the shape is very large and it is determined the define an appropriate shape for the size.

In this study, the shear buckling strengths of the trapezoidal and sinusoidal corrugated plates with the same self-load were compared, and their characteristics and tendencies were analyzed. In the preceding comparative study of corrugation shapes, the corrugation wave depth and the corrugation wave angle were the same. As these target, A linear buckling analysis was conducted, and the differences in the shear buckling mode and the buckling stress were analyzed.

본 연구는 정현형 주름과 마름모형 주름 형상의 전단좌굴 특성을 비교, 분석하는 것이 목적이다. 이를 위해서 동일한 길이의 마름모꼴주름과 정현파주름을 해석대상모델로 채택하였으며, 선형좌굴해석을 통한 전단좌굴특성과 이론식에 의한 특성을 분석하였다. 일반적으로 주름강판의 전단좌굴 형태는 국부좌굴, 전체좌굴 및 두 좌굴에 의한 연성좌굴로 분류된다. 그러나 마름모꼴주름과는 달리 정현파주름형상은 평평한 면이 없기 때문에 전단좌굴의 양상에 대한 경향이 달라진다. 특히 국부좌굴과 전체좌굴의 경계에서 나타나는 전단응력변화와 양상은 주름형태에 의해 차이가 난다. 분석 결과에서 볼 때, 제형 (마름모꼴)의 경우는 이론식내의 전체좌굴과 국부좌굴의 경계에서 연성좌굴모드가 발생했다. 그러나 정현파형의 경우 전체좌굴이 발생하는 구간에서 연성좌굴모드가 발생하는 양상을 보였다. 또한 국부좌굴 구간에는 제형형상이 그리고 전체좌굴 구간에서는 정현파형상이 전단좌굴에 저항하는데 유리하게 작용하였다.

This study analyze the buckling characteristics of trapezoidal and sinusoidal corrugation shapes with same weight. To do this, analyze the shear buckling characteristics through linear buckling analysis and on its theory.

Corrugated steel plates have been used in civil engineering applications such as buildings and bridges, and many studies. These corrugated plate has geometrical characteristic – accordion effect. This study analyzed the elastic shear buckling about geometric parameters of sinusoidal and trapezoidal corrugated plate.