배수 관망에서 가지관은 주 송수관에서 물을 주민에게 공급하는 핵심 요소이나, 일부는 불법적으로 사용되거나 정보가 불확실하여 관망 운영 효율을 저하시킨다. 본 연구는 단순 관망을 대상으로 천이류 해석과 실험을 통해 다중 가지관 탐지 기법을 검증하였다. 연구목적은 천이류 기반 가지관 탐색법의 적용 가능성을 평가하고, 관로 매개변수의 민감성을 분석하는 것이다. 개발된 방법은 단순 관로에서 전통적인 특성선 방법에 볼밸브의 비선형 거동 분석을 연계해 해석했다. 해석과 실험은 동일한 관망에서 두 개의 가지관을 대상으로 수행되었으며, 실험 내재 불확실성을 고려하였다. 두 분석 모두에서 구별 가능한 압력 신호가 확인되어 제안된 방법의 가지관 탐지 가능성을 입증하였다. 또한 결과는 불균일한 파속도와 일관되지 않은 천이류 유입 조건이 탐지 성능에 큰 영향을 미치는 것으로 나타났다.

The purpose of this study is to investigate the dynamic behavior of the internal cabinet of a nuclear power plant due to an earthquake and the characteristics of cabinet vibration reduction by TMD(tuned mass damper). For this purpose, the experimental device was constructed and numerical analysis was performed. The experimental device for the dynamic behavior of the cabinet consists of a cabinet, sliding base, mount, actuator, exciter, and measuring system, and the frequency response function of the cabinet was obtained. In addition, the time history of the cabinet was analyzed for acceleration and displacement through TMD design and cabinet 3D modeling. The natural frequency and response of the cabinet were lowered by approximately 26% due to the structural rigidity of the cabinet under the conditions of door opening and sliding base strong excitation. The acceleration and displacement characteristics of the cabinet varied depending on the TMD mass, and the cabinet vibration reduction effect was the best when the TMD mass was 60kg. The reduction in acceleration and displacement of the cabinet was approximately 12.1–16.2% and 10.1–19.1%, respectively.

This study aims to evaluate the structural safety of a structural thermal barrier, installed inside the structure of a building and performed the role of a load-bearing element and an insulation simultaneously, contributing to the realization of net-zero buildings. To ensure the reliability of the analysis model, the analysis results derived from LS-DYNA were compared with the experimental results. Based on the results shown through the flexural experiment, the reliability of the thermal cross-section insulation structure model for slabs was validated. In addition, the effect of the UHPC block on the load support performance and its contribution to vertical deflection was verified.

저층 침적 위험·유해물질(Hazardous and Noxious Substances)은 해저에 침적되는 위험·유해물질로 직접 및 광학 탐지 기법의 적용 이 어렵기 때문에 수중에서 효과적인 음향 탐지 기법 적용이 요구된다. 본 연구에서는 저층 침적 위험·유해물질인 클로로폼(Chloroform)을 이용한 후방산란신호 측정 실험을 통해 저층 침적 위험·유해물질 음향 탐지 가능성을 확인하였다. 제작된 아크릴 수조 내에 지점토를 이 용하여 웅덩이를 만든 후 Pan&Tilt를 이용하여 수평입사각을 90°에서 50°까지 0.5° 간격으로 변화시켜가며 클로로폼 유무에 따른 후방산란 신호 측정이 수행되었다. 송수신기를 단상태로 주파수 200 kHz, 신호길이 25 인 정현파 신호를 이용하여 송수신하였으며, 클로로폼 유 무에 따른 후방산란신호를 측정하였다. 클로로폼이 침적된 경우 수평입사각 약 80°이하에서 물과 클로로폼 경계면에서의 후방산란신호 수신준위가 작아지는 것이 확인되었다. 물과 클로로폼 경계면에서의 후방산란신호 측정된 결과를 통해 저층 침적 위험·유해물질 음향 탐 지 가능성을 확인하였다.

인류 문명은 재료의 발달과 함께 진화를 해왔으며 20세기 후반부터 등장한 스마트재료는 외부 환경에 맞춰 스스로 적응을 하는 재료이다. 많은 종류의 스마트재료 중 대표물질이라고 할 수 있는 형상기억합금은 온도에 반응하여 자가 치유효과 를 볼 수 있는 재료이다. 외부 하중에 의한 변형을 자가치유 효과를 사용하여 회복을 하고자 하는 연구는 계속되어 왔지만 온 도의 변화를 구조물 전체적으로 줘야한다는 많은 불편이 있었다. 따라서 본 연구에서는 이 효과를 증진하여 상온에서도 자가 치유효과를 할 수 있는 초탄성 형상기억합금을 이용한다. 구조물에 있어서의 초탄성 형상기억합금의 능력을 스테인리스강과 함 께 비교하고 비교를 위해 강재가 가장 변형되기 쉬운 형태인 와이어형태로 가공하여 다양한 인장실험을 진행한다. 인장실험의 종류는 총 3가지로 변위를 다르게, 인장속도를 다르게, 선 인장력을 다르게 하는 실험으로 진행된다. 이때의 응력, 변형률간의 그래프를 그리고 잔류변형, 재료의 항복점 및 회복, 에너지 소산과 같은 구조물에 있어서의 재료적 능력을 파악하고 따로 그래 프를 도식화 하여 해석하였다.

In this study, the structural analysis and welding performance experiments were performed to reduce the weight of the semi-automatic TIG welding device. The structural analysis based on finite element method was performed on the lightweight design of the wire feeder's main frame to evaluate the structural safety and straightness of the lightweight frame. To reduce the weight of the welding wire feeder, the step motor was changed to a servo motor and a pinion gear made of lightweight reinforced plastic material was applied. In addition, a new type of welding torch was developed to reduce the weight of the welding torch and to supply more effective fillers. As a result of performing the TIG welding experiment using a prototype of TIG welding device consisting of a lightweight frame, feeding device and welding torch, it was confirmed that the working criteria were satisfied in terms of welding speed, welding bead shape, feeding uniformity and torch durability. The developed lightweight TIG welding device is expected to improve welding productivity and work convenience.

The performance enhancement of various damping systems from natural hazards has become an highly important issue in engineering field. In this paper, ENTA hysteretic dampers were tested under cyclic loadings to evaluate their performance in terms of ductility and energy dissipation. The test results showed that the hysteretic dampers are effective damping systems to enhance the buildings performance for remodeling and retrofit of buildings. Also, the hysteretic dampers were modeled in FEM(Finite Element Method) structural analysis program. As comparing the computer modeling and the experiment, this study model reflects the nonlinear behavior of steel and derives the hysteresis loop.

When reinforcing an existing reinforced concrete beam-column building with a precast concrete panel, special connection between the PC member and the RC member is required to solve the time dependent deformation of the RC member and to receive the large shear forces. The aim of this study is to obtain the shear strength of upper connection between the existing RC beam-column and infilled PC wall panels in experimentally and theoretically. Thus, the static shear loading tests were conducted on the 6 specimens with the plate connection. Shear failure was resulted from the weakest portion of interior PC panel, exterior RC, and the connection, when the PC portion which located at the center of specimen was pulled upward from the bottom. T he experimental result was compared with analytical result from ACI 318M-14 Chapter 17 for the shear strength of post-installed anchor and PCI Handbook 7th edition 6.8 Structural Steel Corbel (PCI Design Handbook 7th edition, 2010) for the strength of cast-in H-beam. The analytical and experimental results show final failure at the same location. The failure loading of experiment showed larger than average 6% to that of the analysis.

Stable Isotope Analysis (SIA) of carbon and nitrogen is useful tool for the understanding functional roles of target organisms in biological interactions in the food web. Recently, mixing model based on SIA is frequently used to determine which of the potential food sources predominantly assimilated by consumers, however, application of model is often limited and difficult for non-expert users of software. In the present study, we suggest easy manual of R software and package SIAR with example data regarding selective feeding of crustaceans dominated freshwater zooplankton community. We collected SIA data from the experimental mesocosms set up at the littoral area of eutrophic Chodae Reservoir, and analyzed the dominant crustacean species main food sources among small sized particulate organic matters (POM, <50 μm), large sized POM (>50 μm), and attached POM using mixing model. From the results obtained by SIAR model, Daphnia galeata and Ostracoda mainly consumed small sized POM while Simocephalus vetulus consumed both small and large sized POM simultaneously. Copepods collected from the reservoir showed no preferences on various food items, but in the mesocosm tanks, main food sources for the copepods was attached POM rather than planktonic preys including rotifers. The results have suggested that their roles as grazers in food web of eutrophicated reservoirs are different, and S. vetulus is more efficient grazer on wide range of food items such as large colony of phytoplankton and cyanobacteria during water bloom period.

In this study, TbDyFe thin films with the thickness of 1000 Å are fabricated by DC magnetron sputtering. TbDyFe thin films are prepared by DC magnetron sputtering method. The pressure of Ar gas below 1.33 kPa and DC input power of 200 W are used for the sputtering conditions. During sputtering process the substrate holder is heated up to 150 ℃. The thin films are deposited to a thickness of 1000 Å on polyimide substrate with a thickness of 2 μm. The fabricated microstructures are observed by X-ray diffraction (XRD) and the film thickness is measured. Magnetostrictions are determined from the curvature of the thin films which are measured by the optical cantilever method. The experimental results are discussed with numerical data.

The OGS model is configured and used for simulation of the LASGIT project. The modeling conditions and the simulation results from the previous work by Walsh and Calder (2009) are analyzed to see if the simulation configuration is done correctly and to apply for the LASGIT project. Except for the unrealistic modeling conditions used previously, the simulation results successfully demonstrated helium propagation that is typical for the two-phase flow. The results indicated that the relations of capillary pressure and the relative permeability against water saturation used previously should be updated. An elaborated simulation with more realistic parameters should be used to improve the weak points of preliminary work.

본 논문은 복합재료 패널로 보강된 철근 콘크리트 보의 휨 실험과 해석을 통하여 패널의 보강효과에 대하여 알아보고자 한다. FRP 복합재료 패널은 전통적인 재료인 강재와 콘크리트에 비해 단위 무게당 강도 및 강성이 크고 부식에 대한 높은 저항성, 절연성, 고내구성 및 낮은 열전도성 등 우수한 물성으로 유지관리 측면에서 매우 유리하여 최근 많은 연구가 이루어지고 있다. 따라서 본 연구에서는 범용 유한요소 해석 프로그램인 ABAQUS를 이용하여 복합재료 패널로 보강된 철근 콘크리트 보의 극한 하중을 예측하고 실험을 수행하여 그 보강효과에 대한 고찰하였다. 복합재료 패널은 복합재료 패널 층의 유리섬유직조 형태에 따라 LT, DB, DBT로 구분하고 복합재료 패널의 층 개수에 따라 2ply, 3ply로 구분하였다. 실험을 수행한 결과, 해석과 일치하였으며 복합재료 패널로 보강한 철근 콘크리트 보가 극 한강도 측면에서 효율적이었다는 결론도 얻었다.

The paper reviews the methodologies of confirmatory data analysis(CDA) and exploratory data analysis(EDA) in statistical quality control(SQC), design of experiment(DOE) and reliability engineering(RE). The study discusses the properties of flexibility, openness, resistance and reexpression for EDA.