In this paper, a study was conducted on the analysis of communication circuit faults using oscilloscope waveform analysis. Circuit resistance was calculated based on voltage and operating current values using a simple equation, and it was confirmed that the increase in resistance of the communication circuit could be analyzed by analyzing the voltage level during transmitter operation. By combining information of the controller ID, the location of the fault was identified and it was concluded that the location of the fault can be quickly found by analyzing the oscilloscope waveform and the controller ID information. Additionally, the value of communication line contact resistance can be calculated using a simple equation, and the location of the fault can be found by analyzing the communication voltage level and ID information.

전역 최적화 문제의 해를 유전 알고리즘을 사용하여 얻어 완전파형역산을 수행하고 층상 반무한체의 물성치를 추정하는 기법을 제안한다. 조화 수직 하중이 작용하는 층상 반무한체의 동적 응답을 측정하고, 이를 추정 물성치를 사용하여 계산된 응답과 비교한다. 응답의 추정치는 mid-point integrated finite element와 perfectly matched discrete layer를 사용하여 구성된 thin-layer model로부터 얻는다. 전역 최적화 문제의 목적 함수는 응답의 관측치와 추정치의 차이에 대한 L2-norm으로 계산된다. 유전 알고리즘을 사용하여 전역 최적화 문제의 해를 구하여 완전파형역산을 수행한다. 제안된 기법을 기본 진동 모드 뿐만이 아니라 고차 진동 모드도 우세한 다양한 층상 반무한 매질에 적용하여, 측정치가 잡음을 포함하지 않는 경우와 포함하는 경우 모두에 대해서 제안된 완전파형역산 기법은 층상 반무한체의 재료 특성을 추정하는데 적합함을 확인할 수 있다.

In this paper, we investigate the relationship between control system of Bosch system and that of Delphi system by measuring the high and low voltage waveform, current waveform and fuel injection quantity of D-2 and R- engines. Waveform measurements are used the PICO scope and the CDS tester. The injectors of D-2 and R-engines were tested under no load condition using injector with normal fuel injection quantity, injector with small fuel injection quantity and injector with many fuel injection quantity. The relation between current energy and fuel injection quantity shows that the injector variation rate of D2-engine is much larger than that of R-engine. The injector current energy of the D2-engine was more linear than that of the R-engine, therefore making the system more stable. Although the control system of the D2-engine is a more stable system only in terms of the durability of the internal parts of the injector, the injector of the R-engine has a good response because the current value is large.

In this paper, we investigate the relationship between fuel injection quantity and voltage and current energy of Bosch system and Delphi system by measuring the high and low voltage waveform, current waveform, fuel injection quantity and fuel pressure of A and J-engines. Waveform measurements are made using the PICO scope and the CDS tester. The injectors of A and J engines were tested under no load condition using injector with normal fuel injection quantity, injector with small fuel injection quantity and injector with many fuel injection quantity. In case of normal injector, A-engine has higher fuel pressure, injection interval time, voltage energy, and current energy than J-engine. The current energy of the A-engine changed linearly compared to that of the J-engine. For over and under injectors, the change in the previous physical quantity was greater for the A-engine than for the J-engine. However, the duration time of maintaining to open the injector is controlled differently, and so the voltage and current energy values are changed, and the change of the current energy is larger than the voltage energy.

This paper investigates the relationship of voltage and current waveform between normal piezo injector and deterioration abnormal piezo injector. The experimental methods using Pico oscilloscope and GDS scan tool are employed to measure current and voltage waveform and fuel pressure of piezo injector. The experiment is carried out during no-load condition. A summary of the important results are as follows. 1) In case of normal injector, the fluctuation of duration time of piezo injector was linearly and regularly decreased with increasing engine speed, but the that of deterioration piezo injector was irregularly decreased with increasing engine speed. 2) In main injection, the peak value of the current waveform of abnormal injector was larger than that of normal injector, the duration time of deteriorated abnormal injector was less than that of normal injector at 800rpm and 1500rpm, but the duration time of deteriorated abnormal injector was larger than that of normal injector at 2000rpm and 3000rpm. This irregularity appears to be caused by the deterioration of the injector.

In this paper, the influence of the injector failure of the GDI engine on the air-fuel ratio inside the combustion chamber can be analyzed through time and shape analysis of the damping process of the ignition coil secondary waveform at 800rpm, 1500rpm, 2000rpm, 3000rpm. In particular, there is a correlation that affects air pollution associated with global warming, such as HC and NOx. To prevent this, periodic injector inspections can improve the fuel efficiency of the vehicle and reduce exhaust pollutants.

In this paper, we investigate the trend of injector waveform change due to failure of air flow sensor and intake air temperature sensor of CRDI engine. Changes in the injector opening time can be detected by the failure of the associated sensor, and the extension of the reaction time is closely related to fuel consumption. Thus, the proper maintenance time of the vehicle will affect the fuel economy and reduce the exhaust gas.

This paper is on developing the waveform analysis method in driving control of solenoid injector of CRDI diesel engine. The experimental methods using Pico oscilloscope and scan tool is employed to measure current and voltage waveform of solenoid injector. The solenoid injector are used 1 normal and 2 abnormal injectors. The experiment is carried out during no-load condition. The magnitude of pressure drop is largest main duration, pre and pilot duration in the order named in case of normal injector, whereas was largest pilot duration, pre and main duration in the order named in case of abnormal injectors.

The test was done on cars travelling at the speeds of 20km/h, 60km/h and 100km/h using the performance testing mode for chassis dynamometer. In this test, the secondary ignition waveform, exhaust emissions and fuel consumption were measured in case of faulty MAP sensor, faulty oxygen sensor and spark plugs. The following results from the related analysis of secondary waveform, emission and fuel consumption measurements were obtained : 1) The fuel consumption was higher in the order of oxygen sensor trouble, MAP trouble, spark plug trouble, before maintenance and after maintenance. Maximum fuel economy is 9.3km/L, the minimum fuel economy is 3.2km/L, the difference between max. and min. is 65.5%. 2) If you compare the oxygen sensor trouble with after maintenance, the CO has improved an average of 98%, fuel economy average of 60%. And the HC has improved an average of 87%, fuel economy average of 60%. The fuel consumption and exhaust gas was bad in the order of oxygen sensor trouble, MAP trouble and S/P trouble.

This paper investigates the waveform analysis of voltage and current waveform from CRDI engine. It is on developing on analysis method of waveform CRDI Diesel engine. The experimental methods using Pico oscilloscope are employed to measure current and voltage waveform of solenoid injector from CRDI engine. The one normal and two abnormal solenoid injectors are used. The experiment is carried out during no-load condition. A summary of the important results are as follows. 1) The area of the voltage and current waveform of the abnormal injector becomes larger than the that of normal injector. 2) The area of the current waveform can be obtained more accurate results than that of voltage waveform.

DC-EPG 시스템을 활용하여 애멸구(Laodelphax striatellus) 암컷 성충이 벼를 섭식하는 동안 발생되는 전기적 신호를 기록하고 분석하여, 벼멸구에서 보고된 것(Seo et al., 2009)과 같은 방식으로, np, L1, L2, L3, L4-a, L4-b, L5의 7 개 EPG 파형으로 구별하였다. 파형들의 모양과 발 생 패턴은 벼멸구(Nilaparvata lugens)와 매우 유사하였고, L4-b의 직전에는 반드시 L3와 L4-a가 연속된 순서로 나타났다. 감로는 L4-b에서 주기 적으로 분비되었다. 레이저 stylectomy 후 섭식부분의 미세절편을 관찰한 결과, 애멸구 구침의 끝이 L3와 L4-a, L4-b에서는 벼의 체관부 근처 또 는 체관부에서 관찰된 반면, L5에서는 물관부에서 관찰되었다. 레이저 stylectomy로 L4-b에서 잘려진 애멸구 구침의 절단부로부터 유일하게 벼 수액이 용출되었고, HPLC로 분석된 수액 안의 당 성분으로 식물의 체관부 탄수화물 이동태인 설탕(sucrose)만이 검출되었다. 이상의 관찰 결과 와 애멸구의 EPG 파형 전개 과정 분석을 통해, L1과 L2는 관다발 도달 전에 발생하는 구침을 찌르고 타액 분비가 동반된 구침의 이동 행동으로, L3와 L4-a는 체관부에서 섭식을 위해 사전에 준비하는 과정으로, L4-b는 체관부 수액을 흡즙하는 행동으로, 마지막으로 L5는 물관부에서 형성되 는 섭식행동으로 벼멸구와 유사하게 결론지었다.

We introduce a depth scaling strategy to improve the accuracy of frequency-domain elastic full waveform inversion (FWI) using the new pseudo-Hessian matrix for seismic data without low-frequency components. The depth scaling strategy is based on the fact that the damping factor in the Levenberg-Marquardt method controls the energy concentration in the gradient. In other words, a large damping factor makes the Levenberg-Marquardt method similar to the steepest-descent method, by which shallow structures are mainly recovered. With a small damping factor, the Levenberg-Marquardt method becomes similar to the Gauss-Newton methods by which we can resolve deep structures as well as shallow structures. In our depth scaling strategy, a large damping factor is used in the early stage and then decreases automatically with the trend of error as the iteration goes on. With the depth scaling strategy, we can gradually move the parameter-searching region from shallow to deep parts. This flexible damping factor plays a role in retarding the model parameter update for shallow parts and mainly inverting deeper parts in the later stage of inversion. By doing so, we can improve deep parts in inversion results. The depth scaling strategy is applied to synthetic data without lowfrequency components for a modified version of the SEG/EAGE overthrust model. Numerical examples show that the flexible damping factor yields better results than the constant damping factor when reliable low-frequency components are missing.

This study analyzed by measuring the voltage waveform of the injector intended for operating CRDI diesel vehicle. The cases of the EGR trouble and a EGR normal is considered. 1) The voltage waveform in the case of the normal and trouble, the difference between the maximum voltage was not large, decrease in the number of voltage gated pulses with the increase in engine speed, sustained current remained for this period. 2) The voltage waveform, comparing the case of the normal case and trouble, the size of the maximum voltage, no large change in gate pulse voltage is to be generated than in the case of a defective irregular longer opening time of the injector factor it was possible to know the bad influence on the fuel efficiency.

AC PDP의 Vt 폐곡선 측정에 의하여 개방형 유전체 구조에서 방전 전압과 내부 벽전압 등의 방전 특성이 종래의 구조와 비교되어 조사되었다. 개방형 유전체 구조는 상판 전극사이의 유전체를 없애서 유지 전극간의 방전이 더욱 쉽게 발생하도록 하는 구조이다. 개방형 유전체 구조에서 상판의 두 전극인 주사와 유지전극 간 방전 개시전압이 종래의 구조와 다르기 때문에 종래의 기입파형을 포함한 초기화 파형도 수정되어져야 한다. Vt 폐곡선 분석에 기초하여 개방형 유전체 구조에 적합한 수정된 구동파형이 제안되었고 42인치 AC PDP에서 실험되었다.

The experiment was carried out during no-load condition for analysis of the relativity between MAP, hot film, oxygen, the secondary ignition and injector waveform. The experimental methods using oscilloscope were employed to measure waveform. The relativity between several waveform and the secondary waveform coming from ignition coil were measured in case of three decrepit vehicles. From these results, a summary of the important results are as follows. 1. Through fast acceleration experiments, the response time values of hot film sensor and oxygen sensor was faster than the those of the MAP sensor and oxygen sensor. 2. The values of spark line duration time was largest A, C, B type in the order named. And discharge energy of the secondary ignition waveform was largest A, B, C type 3. The value of effective discharge energy is to be nearly proportional to the spark line duration time. 4. The value of effective discharge energy directly increases as revolutions per minute increase, and the value of spark line duration time decreases as revolutions per minute increase.

본 논문에서는 물성이 균일하지 않은 반무한 고체영역의 탄성파속도 분포를 재구성하기 위한 시간영역 Gauss-Newton 전체파형 역해석 기법을 소개한다. 반무한 영역을 유한 계산영역으로 치환하기 위하여 유한영역의 경계에 수치적 파동흡수 경계조건인 perfectly-matched-layers(PMLs)를 도입하였다. 이 역해석 문제는 PML을 경계로 하는 영역에서의 탄성파동방정식을 구속조건으로 하는 최적화 문제로 성립되며, 표면에서 측정된 변위응답과 혼합유한요소법에 의해 계산된 응답간의 차이를 최소화함으로써 미지의 탄성파속도 분포를 결정한다. 이 과정에서 Gauss-Newton-Krylov 최적화 알고리즘과 정규화기법을 사용하여 탄성파속도의 분포를 반복적으로 업데이트하였다. 1차원 수치예제들을 통해 Gauss-Newton 역해석으로 부터 재구성된 탄성파속도의 분포가 목표값에 충분히 근사함을 보였으며, Fletcher Reeves 최적화 알고리즘을 사용한 기존의 역해석 결과에 비해 수렴율이 현저히 개선되고 계산 소요시간이 단축됨을 확인할 수 있었다.

이 논문에서는 반무한 고체영역의 표면에서 측정한 변위응답의 시간이력으로부터 유한요소망 연속기법을 이용해 탄성파속도의 공간적 분포를 추정하는 역해석 문제를 소개한다. 반무한 영역에서의 역해석을 위해서는 해석 대상이 되는 유한영역의 경계에서 파동의 반사가 일어나지 않도록 하는 것이 중요하다. 이를 위해 유한영역의 경계면에 perfectly-matchedlayers(PMLs)라는 수치적 파동흡수층을 도입하였고, PML을 경계로 하는 유한영역에서 역해석 문제를 정의하였다. 이 문제를 탄성파동방정식을 구속조건으로 하는 최적화 문제로 표현하였으며, 라그랑주 승수법에 기초한 비구속 최적화 기법에 의해 탄성파속도의 최적 분포를 결정하였다. 해의 정확도와 수렴성을 높이기 위해 유한요소망 연속기법을 도입하여 점진적으로 밀도가 증가하는 유한요소망에 대해 연속적으로 역해석을 수행하였다. 1차원 예제들을 통해 유한요소망 연속기법을 이용한 역해석으로부터 탄성파속도의 분포를 정확히 추정할 수 있음을 확인하였으며, 측정 응답에 노이즈가 존재하는 경우에도 제안한 역해석 기법은 목표 탄성파속도 분포에 근사한 결과를 도출하였다.

This paper is on developing the advanced method in diagnosis electronic control of gasoline and LPG engine. The experimental methods using oscilloscope were employed to measure waveform of hot wire, hot film, oxygen, ignition coil and injector. Through these analysis, emission reduction and fuel economy improvement were expected by depict vehicles. The experiment was carried out during no-load condition. A summary of the important results are as follows. 1. The factors affecting the secondary ignition waveform from the primary ignition waveform were reverse surge voltage and induced voltage . Actually shape of primary ignition waveform was normal, but a secondary ignition waveform was measured badly. 2. The area of the voltage-time diagram of secondary ignition waveform means the value of the effective discharge of energy. This value is negative, the fuel economy could be predicted badly and is positive, good value of fuel economy could be predicted. 3. Inspection and maintenance of DLI ignition vehicles compared to DIS ignition vehicles were essential. The secondary ignition waveform of the C type vehicle were worst compare to those of the different type vehicles. The injection duration of injector was largest C, D types in the order named, was shortest E, F type. As a result, E, F type are most effective among Gasoline vehicles.