ZnO thin films are of considerable interest because they can be customized by various coating technologies to have high electrical conductivity and high visible light transmittance. Therefore, ZnO thin films can be applied to various optoelectronic device applications such as transparent conducting thin films, solar cells and displays. In this study, ZnO rod and thin films are fabricated using aqueous chemical bath deposition (CBD), which is a low-cost method at low temperatures, and environmentally friendly. To investigate the structural, electrical and optical properties of ZnO for the presence of citrate ion, which can significantly affect crystal form of ZnO, various amounts of the citrate ion are added to the aqueous CBD ZnO reaction bath. As a result, ZnO crystals show a nanorod form without citrate, but a continuous thin film when citrate is above a certain concentration. In addition, as the citrate concentration increases, the electrical conductivity of the ZnO thin films increases, and is almost unchanged above a certain citrate concentration. Cu(In,Ga)Se2 (CIGS) solar cell substrates are used to evaluate whether aqueous CBD ZnO thin films can be applicable to real devices. The performance of aqueous CBD ZnO thin films shows performance similar to that of a sputter-deposited ZnO:Al thin film as top transparent electrodes of CIGS solar cells.

We report on the fabrication and photoelectrochemical(PEC) properties of a Cu2O thin film/ZnO nanorod array oxide p-n heterojunction structure with ZnO nanorods embedded in Cu2O thin film as an efficient photoelectrode for solardriven water splitting. A vertically oriented n-type ZnO nanorod array was first prepared on an indium-tin-oxide-coated glass substrate via a seed-mediated hydrothermal synthesis method and then a p-type Cu2O thin film was directly electrodeposited onto the vertically oriented ZnO nanorods array to form an oxide semiconductor heterostructure. The crystalline phases and morphologies of the heterojunction materials were characterized using X-ray diffraction and scanning electron microscopy as well as Raman scattering. The PEC properties of the fabricated Cu2O/ZnO p-n heterojunction photoelectrode were evaluated by photocurrent conversion efficiency measurements under white light illumination. From the observed PEC current density versus voltage (J-V) behavior, the Cu2O/ZnO photoelectrode was found to exhibit a negligible dark current and high photocurrent density, e.g., 0.77 mA/cm2 at 0.5 V vs Hg/HgCl2 in a 1 mM Na2SO4 electrolyte, revealing an effective operation of the oxide heterostructure. In particular, a significant PEC performance was observed even at an applied bias of 0 V vs Hg/ HgCl2, which made the device self-powered. The observed PEC performance was attributed to some synergistic effect of the p-n bilayer heterostructure on the formation of a built-in potential, including the light absorption and separation processes of photoinduced charge carriers.

We report on the efficient detection of NO gas by an all-oxide semiconductor p-n heterojunction diode structure comprised of n-type zinc oxide (ZnO) nanorods embedded in p-type copper oxide (CuO) thin film. The CuO thin film/ZnO nanorod heterostructure was fabricated by directly sputtering CuO thin film onto a vertically aligned ZnO nanorod array synthesized via a hydrothemal method. The transport behavior and NO gas sensing properties of the fabricated CuO thin film/ ZnO nanorod heterostructure were charcterized and revealed that the oxide semiconductor heterojunction exhibited a definite rectifying diode-like behavior at various temperatures ranging from room temperature to 250 oC. The NO gas sensing experiment indicated that the CuO thin film/ZnO nanorod heterostructure had a good sensing performance for the efficient detection of NO gas in the range of 2-14 ppm under the conditions of an applied bias of 2 V and a comparatively low operating temperature of 150 oC. The NO gas sensing process in the CuO/ZnO p-n heterostructure is discussed in terms of the electronic band structure.

The effects of an addition of CNT on the sensing properties of nano ZnO:CNT-based gas sensors were studied for H2S gas. The nano ZnO sensing materials were grown by a hydrothermal reaction method. The nano ZnO:CNT was prepared by ball-milling method. The weight range of the CNT addition on the ZnO surface was from 0 to 10%. The nano ZnO:CNT gas sensors were fabricated by a screen-printing method on alumina substrates. The structural and morphological properties of the ZnO:CNT sensing materials were investigated by XRD, EDS, and SEM. The XRD patterns revealed that nano ZnO:CNT powders with a wurtzite structure were grown with (1 0 0), (0 0 2), and (1 0 1) dominant peaks. The size of the ZnO was about 210 nm, as confirmed by SEM images. The sensitivity of the nano ZnO:CNT-based sensors was measured for 5 ppm of H2S gas at room temperature by comparing the resistance in air with that in target gases.

The effects of a Ni coating on the sensing properties of nano ZnO:Ni based gas sensors were studied for CH4 and CH3CH2CH3 gases. Nano ZnO sensing materials were prepared by the hydrothermal reaction method. The Ni coatings on the nano ZnO surface were deposited by the hydrolysis of zinc chloride with NH4OH. The weight % of Ni coating on the ZnO surface ranged from 0 to 10 %. The nano ZnO:Ni gas sensors were fabricated by a screen printing method on alumina substrates. The structural and morphological properties of the nano ZnO : Ni sensing materials were investigated by XRD, EDS, and SEM. The XRD patterns showed that nano ZnO : Ni powders with a wurtzite structure were grown with (1 0 0), (0 0 2), and (1 0 1) dominant peaks. The particle size of nano ZnO powders was about 250 nm. The sensitivity of nano ZnO:Ni based sensors for 5 ppm CH4 gas and CH3CH2CH3 gas was measured at room temperature by comparing the resistance in air with that in target gases. The highest sensitivity of the ZnO:Ni sensor to CH4 gas and CH3CH2CH3 gas was observed at Ni 4 wt%. The response and recovery times of 4 wt% Ni coated ZnO:Ni gas sensors were 14 s and 15 s, respectively.

The ZnO thin films were grown on GaN template substrates by RF magnetron sputtering at different RF powers and n-ZnO/p-GaN heterojunction LEDs were fabricated to investigate the effect of the RF power on the characteristics of the n-ZnO/p-GaN LEDs. For the growth of the ZnO thin films, the substrate temperature was kept constant at 200˚C and the RF power was varied within the range of 200 to 500W at different growth times to deposit films of 100 nm thick. The electrical, optical and structural properties of ZnO thin films were investigated by ellipsometry, X-ray diffraction (XRD), atomic force microscopy (AFM), photoluminescence (PL) and by assessing the Hall effect. The characteristics of the n-ZnO/p-GaN LEDs were evaluated by current-voltage (I-V) and electroluminescence (EL) measurements. ZnO thin films were grown with a preferred c-axis orientation along the (0002) plane. The XRD peaks shifted to low angles and the surface roughness became non-uniform with an increase in the RF power. Also, the PL emission peak was red-shifted. The carrier density and the mobility decreased with the RF power. For the n-ZnO/p-GaN LED, the forward current at 20 V decreased and the threshold voltage increased with the RF power. The EL emission peak was observed at approximately 435 nm and the luminescence intensity decreased. Consequently, the crystallinity of the ZnO thin films grown with RF sputtering powers were improved. However, excess Zn affected the structural, electrical and optical properties of the ZnO thin films when the optimal RF power was exceeded. This excess RF power will degrade the characteristics of light emitting devices.

We have investigated the structural and electrical properties of Ga-doped ZnO (GZO) thin films deposited by anRF magnetron sputtering at various RF powers from 50 to 90W. All the GZO thin films are grown as a hexagonal wurtzitephase with highly c-axis preferred parameters. The structural and electrical properties are strongly related to the RF power. Thegrain size increases as the RF power increases since the columnar growth of GZO thin film is enhanced at an elevated RFpower. This result means that the crystallinity of GZO is improved as the RF power increases. The resistivity of GZO rapidlydecreases as the RF power increases up to 70W and saturates to 90W. In contrast, the electron concentration of GZO increasesas the RF power increases up to 70W and saturates to 90W. GZO thin film shows the lowest resistivity of 2.2×10−4Ωcmand the highest electron concentration of 1.7×1021cm−3 at 90W. The mobility of GZO increases as the RF power increasessince the grain boundary scattering decreases due to the reduced density of the grain boundary at a high RF power. Thetransmittance of GZO thin films in the visible range is above 90%. GZO is a feasible transparent electrode for application asa transparent electrode for thin film solar cells.

We have investigated the structural and optical properties of Ga-doped ZnO (GZO) thin films deposited by RFmagnetron sputtering at various deposition temperatures from 100 to 500oC. All the GZO thin films are grown as a hexagonalwurtzite phase with highly c-axis preferred parameter. The structural and electrical properties are strongly related to depositiontemperature. The grain size increases with the increasing deposition temperature up to 400oC and then decreases at 500oC. Thedependence of grain size on the deposition temperature results from the variation of thermal activation energy. The resistivityof GZO thin film decreases with the increasing deposition temperature up to 300oC and then decreases up to 500oC. GZO thinfilm shows the lowest resistivity of 4.3×10−4Ωcm and highest electron concentration of 1.0×1021cm−3 at 300oC. The mobilityof GZO thin films increases with the increasing deposition temperature up to 400oC and then decreases at 500oC. GZO thinfilm shows the highest resistivity of 14.1cm2/Vs. The transmittance of GZO thin films in the visible range is above 87% atall the deposition temperatures. GZO is a feasible transparent electrode for the application to the transparent electrode of thinfilm solar cells.

Changes in surface morphology and roughness of dc sputtered ZnO:Al/Ag back reflectors by varying the deposition temperature and their influence on the performance of flexible silicon thin film solar cells were systematically investigated. By increasing the deposition temperature from 25˚C to 500˚C, the grain size of Ag thin films increased from 100 nm to 1000 nm and the grain size distribution became irregular, which resulted in an increment of surface roughness from 6.6 nm to 46.6 nm. Even after the 100 nm thick ZnO:Al film deposition, the surface morphology and roughness of the ZnO:Al/Ag double structured back reflectors were the same as those of the Ag layers, meaning that the ZnO:Al films were deposited conformally on the Ag films without unnecessary changes in the surfacefeatures. The diffused reflectance of the back reflectors improved significantly with the increasing grain size and surface roughness of the Ag films, and in particular, an enhanced diffused reflectance in the long wavelength over 800 nm was observed in the Ag back reflectors deposited at 500˚C, which had an irregular grain size distribution of 200-1000 nm and large surface roughness. The improved light scattering properties on the rough ZnO:Al/Ag back reflector surfaces led to an increase of light trapping in the solar cells, and this resulted in a noticeable improvement in the Jsc values from 9.94 mA/cm2 for the flat Ag back reflector at 25˚C to 13.36 mA/cm2 for the rough one at 500˚C. A conversion efficiency of 7.60% (Voc = 0.93, Jsc = 13.36 mA/cm2, FF = 61%) was achieved in the flexible silicon thin film solar cells at this moment.

We studied the initial reaction mechanism of Zn precursors, namely, di-methylzinc (Zn(CH3)2, DMZ) and diethylzinc (Zn(C2H5)2, DEZ), for zinc oxide thin-film growth on a Si (001) surface using density functional theory. We calculated the migration and reaction energy barriers for DMZ and DEZ on a fully hydroxylized Si (001) surface. The Zn atom of DMZ or DEZ was adsorbed on an O atom of a hydroxyl (-OH) due to the lone pair electrons of the O atom on the Si (001) surface. The adsorbed DMZ or DEZ migrated to all available surface sites, and rotated on the O atom with low energy barriers in the range of 0.00-0.13 eV. We considered the DMZ or DEZ reaction at all available surface sites. The rotated and migrated DMZs reacted with the nearest -OH to produce a uni-methylzinc (-ZnCH3, UMZ) group and methane (CH4) with energy barriers in the range of 0.53-0.78 eV. In the case of the DEZs, smaller energy barriers in the range of 0.21-0.35 eV were needed for its reaction to produce a uni-ethylzinc (-ZnC2H5, UEZ) group and ethane (C2H6). Therefore, DEZ is preferred to DMZ due to its lower energy barrier for the surface reaction.

Transparent conducting oxide (TCO) films are widely used for optoelectronic applications. Among TCO materials,zinc oxide (ZnO) has been studied extensively for its high optical transmission and electrical conduction. In this study, the effectsof O2 plasma pretreatment on the properties of Ga-doped ZnO films (GZO) on polyethylene naphthalate (PEN) substrate werestudied. The O2 plasma pretreatment process was used instead of conventional oxide buffer layers. The O2 plasma treatmentprocess has several merits compared with the oxide buffer layer treatment, especially on a mass production scale. In this process,an additional sputtering system for oxide composition is not needed and the plasma treatment process is easily adopted as anin-line process. GZO films were fabricated by RF magnetron sputtering process. To improve surface energy and adhesionbetween the PEN substrate and the GZO film, the O2 plasma pre-treatment process was used prior to GZO sputtering. As theRF power and the treatment time increased, the contact angle decreased and the RMS surface roughness increased significantly.It is believed that the surface energy and adhesive force of the polymer surfaces increased with the O2 plasma treatment andthat the crystallinity and grain size of the GZO films increased. When the RF power was 100W and the treatment time was120 sec in the O2 plasma pretreatment process, the resistivity of the GZO films on the PEN substrate was 1.05×10-3Ω-cm,which is an appropriate range for most optoelectronic applications.

Various thicknesses of Al-doped ZnO (AZO) films were deposited on glass substrate using pulsed dcmagnetron sputtering with a cylindrical target designed for large-area high-speed deposition. The structural,electrical, and optical properties of the films of various thicknesses were characterized. All deposited AZO filmshave (0002) preferred orientation with the c-axis perpendicular to the substrate. Crystal quality and surfacemorphology of the films changed according to the film thickness. The samples with higher surface roughnessexhibited lower Hall mobility. Analysis of the measured data of the optical band gap and the carrierconcentration revealed that there were no changes for all the film thicknesses. The optical transmittances weremore than 85% regardless of film thickness within the visible wavelength region. The lowest resistivity,4.13×10-4Ω·cm-1, was found in 750nm films with an electron mobility (µ) of 10.6cm2V-1s-1 and a carrierconcentration (n) of 1.42×1021cm-3.

Changes in the surface morphology and light scattering of textured Al doped ZnO thin films on glasssubstrates prepared by rf magnetron sputtering were investigated. As-deposited ZnO:Al films show a hightransmittance of above 80% in the visible range and a low electrical resistivity of 4.5×10-4Ω·cm. The surfacemorphology of textured ZnO:Al films are closely dependent on the deposition parameters of heater temperature,working pressure, and etching time in the etching process. The optimized surface morphology with a cratershape is obtained at a heater temperature of 350oC, working pressure of 0.5 mtorr, and etching time of 45seconds. The optical properties of light transmittance, haze, and angular distribution function (ADF) aresignificantly affected by the resulting surface morphologies of textured films. The film surfaces, havinguniformly size-distributed craters, represent good light scattering properties of high haze and ADF values.Compared with commercial Asahi U (SnO2:F) substrates, the suitability of textured ZnO:Al films as frontelectrode material for amorphous silicon thin film solar cells is also estimated with respect to electrical andoptical properties.

rf 마그네트론 스퍼터링법을 이용하여 7059 유리기판 위에 ZnO압전박막을 증착하고, 공정변수인 rf 인가전력, 반응기 압력, O2/Ar의 조성비등이 증착되는 박막의 결정성 및 전기적 특성에 미치는 영향을 고찰하였다. 증착된 ZnO박막은 문헌에 보고된 증착속도보다 높은 값(200-1000Å/min)을 가졌으며, XRD(002)피크의 rocking curve 표준편차가 SAW 필터로의 응용이 가능한 6˚미만의 값을 가졌다. O2Ar 유입비가 25%이상의 경우에는 매우 높은 저항치를 가짐을 알 수 있었다. ZnO박막의 두께와 파장의 비, hλ=0.25인 조건에서 필터를 제조하였다. 측정한 주파수 응답특성과 이론치에 의해 계산한 주파수응답특성은 비교적 잘 일치함을 알 수 있었다. 이때 중심주파수는 39.08MHz였으며, 상속도는 ? 2501m/sec, 삽입손실은 약 29dB였다.