PURPOSES : This study aims at evaluating the use of an electromagnetic density gauge (EDG) to measure the in situ density and air-void content of asphalt concrete (AC) pavement. METHODS : In situ AC pavement density and air-void readings were obtained from two sites (Daegu and Ulsan) using an EDG. Calibration of the EDG was conducted by first obtaining density values at three different positions, on each pavement where core samples were extracted afterward. The core samples were then tested to obtain laboratory density and air-void values. The density measured using the EDG was then subtracted from the laboratory values to obtain the offset calibration values, which were then adopted to calibrate the in situ measurements using the EDG. Moreover, to analyze the effect of moisture on the pavement surface, EDG measurements were conducted under dry and wet conditions to compare the in-situ readings. RESULTS : The in-situ density readings of AC tend to be higher in moist/wet conditions. By applying the calibration value to the EDG readings, the density error percentage was reduced from 0.61% to 0.096%, and 0.64% to 0.16% for Daegu and Ulsan sites, respectively. Consequently, the air-void content error percentage was reduced from 12.8% to 1.04%, and from 10.07% to 1.78% for Daegu and Ulsan sites, respectively. CONCLUSIONS : The electromagnetic density gauge (EDG) is an effective tool for the non-destructive measurement of in situ pavement density. By applying offset calibration values, the error in the field readings was reduced, and the accuracy of the EDG measurements was improved.

PURPOSES : This study aims to reduce the urban heat island phenomenon via utilization of porous asphalt pavements. METHODS : One of the many known functions of porous asphalt is that it reduces the urban heat island phenomenon. Indoor experiments were conducted to compare the surface temperature of sprinkled dense-graded and porous asphalt and outdoor experiments were conducted to verify the difference between the two asphalt pavements under external conditions. RESULTS : The results of the indoor experiment demonstrated that the temperatures of the two pavements were similar and that the porous asphalt pavement exhibited low temperature when sprinkled; the temperature of the porous asphalt was approximately 2 °C lower than that of the dense-graded asphalt pavement. The results of the outdoor experiment showed that the peak temperatures of the two pavements were approximately the same as usual. However, it was confirmed that the surface temperature of the porous asphalt pavement at night after sunset was lower than that of the dense-graded asphalt pavement and that the peak temperature dropped for approximately 1~2 days after the rainfall.. CONCLUSIONS : Porous asphalt pavement has a lower surface temperature than normal dense-graded asphalt pavement, under the presence of moisture in the pavement. In addition, it was confirmed that the lower surface temperature of the porous asphalt pavement is due to the low heat emission of the pavement at night. Accordingly, it is believed that the application of the porous asphalt pavement will not only have known effects but also significant impacts on the reduction of urban heat island phenomena.

PURPOSES : The objective of this study is to address various problems, such as an increase in material cost and premature failure (e.g., cracks and potholes) of porous pavements, and to develop multifunctional asphalt and asphalt mixtures to ensure the long-term commonality of porous asphalt pavements. METHODS : A basic quality test of two types of porous asphalt mixtures was performed. One type consisted of the existing porous asphalt mixture, using domestically presented grading, and the other a porous asphalt mixture using high-viscosity modified asphalt with enhanced low-temperature properties, aimed at improving strain resistance and developed by applying the grading suggested by the Federal Highway Administration (FHWA). RESULTS : The cantabros loss rate was 19.62 % for conventional modified asphalt (PG 82-22) and 5.95 % for the developed highviscosity modified asphalt (PG 88-28), indicating that both mixtures passed the criteria. Regarding the drain-down loss rate, mixtures using both types of asphalt were found to pass all quality standards. The average permeability coefficients for each porous asphalt mixture were 0.023 and 0.018 and both types of porous asphalt mixtures satisfied the quality standard of 0.01 cm/s, as given by the Asphalt Concrete Pavement Guidelines of the Ministry of Land, Infrastructure, and Transport. CONCLUSIONS : As a result of the mix design of the two porous asphalt mixtures, the mixture developed in this study was found to be superior to the conventional porous asphalt mixture using conventional porous asphalt grading and modified asphalt.

PURPOSES : The purpose of this study is to evaluate the performance characteristics of stone mastic asphalt (SMA) pavement by comparison with polymer modified asphalt (PMA) pavement and conventional asphalt pavement, to check the performance characteristics according to the pavement type, pavement materials, traffic volume, and environmental factors and to analyze the quality variation characteristics according to the pavement materials using data extracted from the database of the expressway long-term pavement performance. METHODS : Approximately 10% outlier data of pavement performance data were excluded in order to increase the reliability of the analysis results before evaluating the asphalt pavement performance. The performance model was developed through linear regression analysis by setting the performance period as the independent variable and the highway pavement condition index (HPCI) as the dependent variable. Descriptive statistic analysis of HPCI using the static package for social science (SPSS) tool and the analysis of variance was performed to identify the quality variation characteristics according to the pavement materials. The amount of de-icing agent and traffic level of service were classified as two levels in order to check the influence of traffic volume and environmental factors on the performance characteristics of the asphalt pavement. RESULTS : The tentative pavement performance lives were calculated at 19.3 years for new the SMA pavement (GPS-2), 14.3 years for the SMA overlay on the asphalt pavement (GPS-6), and 10.3 years for the SMA overlay on the concrete pavement (GPS-7). In case of the asphalt overlay, the tentative performance lives were calculated at 8.2 years for the PMA overlay on the asphalt pavement (GPS-6), 7.2 years for the PMA overlay on the concrete pavement (GPS-7), 7.2 years for the conventional asphalt overlay on the asphalt pavement (GPS-6), and 5.5 years for the conventional asphalt overlay on the concrete pavement (GPS-7). CONCLUSIONS : It was confirmed that the SMA pavement showed better performance and quality variation characteristics than the PMA and conventional asphalt pavement. The performance characteristics of the asphalt pavement (GPS-2) was better than the asphalt overlay pavement, and the asphalt overlay on the asphalt pavement (GPS-6) had better performance characteristics than the asphalt overlay on the concrete pavement (GPS-7). It was observed that the asphalt overlay on the asphalt pavement (GPS-6) was strongly influenced by the traffic volume and the asphalt overlay on concrete pavement (GPS-7) was strongly influenced by the traffic volume and de-icing agent.

PURPOSES : The purpose of this study is to evaluate the performance of an ultra-thin asphalt pavement as a preventive maintenance approach through laboratory tests. METHODS : An ultra-thin asphalt pavement of 2 cm wearing course thickness comprising modified asphalt and aggregate is a preventive maintenance method used for asphalt pavements. A mix design was carried out to determine the optimum aggregate gradation and asphalt contents. A dynamic immersion test was performed to evaluate the water-resistance of the ultra-thin asphalt pavement. A wet track abrasion test and a cohesion test were conducted to examine the applicability of the ultra-thin asphalt pavement in surface treatment. The performance of the ultra-thin asphalt pavement was evaluated through wheel loading tests, such as Hamburg wheel-tracking and third-scale model mobileloading simulator (MMLS-3). RESULTS : An optimum binder content of 4.9% was obtained in the ultra-thin asphalt mixture from the Marshall mix design. The waterresistance tests indicated a 70% dynamic immersion coverage rate of the ultra-thin asphalt pavement. The wet track abrasion test showed an abrasion rate of 0.0107 g/cm2, and the cohesion tests indicated a 19.0 kg·cm average cohesion at 30 min of operating time and 21.4 kg·cm average cohesion at 60 min of operating time. From the Hamburg wheel-tracking test, a 16.56 mm rut depth at 20,000 wheel passing was obtained. Finally, a 5.87 mm rut depth at 300,000 number of wheel passing was detected from the MMLS-3 test. CONCLUSIONS : The water-resistance of the ultra-thin asphalt pavement satisfied the recommended guidelines of the Korean Ministry of Land, Infrastructure and Transport. In addition, the applicability of the ultra-thin asphalt pavement as a surface treatment met the standard of the International Slurry Surfacing Association. Furthermore, the deformation performance of the ultra-thin asphalt pavement was 1.5 times better than that of the straight asphalt pavement, based on the results of the wheel-loading tests. Hence, it is estimated that an ultra-thin asphalt pavement has a high performance in the preventive maintenance of asphalt pavement, even though the cracking resistance was not evaluated in this study.

PURPOSES: Investigating road pavement conditions using an investigation vehicle is challenging especially if repeated driving is required on the by-lane, and the traffic in the investigation section is heavy. A technology used to investigate the road pavement conditions is studied herein using image data obtained by drone photography. METHODS : Flight plans were made for the survey areas, and ground control point measurements were performed. The research section was filmed using drones. The acquired image data were modeled using Pix4Dmapper. The images taken by the drones were used to investigate the road pavement cracks. A digital surface model was extracted from the Pix4Dmapper modeling results using the Global Mapper program to investigate plastic deformation and flatness. As regards plastic deformation, the elevation of each point was extracted at intervals of 50 cm and 10 cm in the longitudinal and lateral directions, respectively, for 20 m× 10 m of the entire road. In terms of flatness, the elevation values for each point were extracted at intervals of 5 cm and 10 cm for the wheel path and 20 m for the entire roadway. RESULTS: This study compared drone-captured images, which were consistent, and vehicle scan images and confirmed that the former can detect a large number of cracks on road surfaces. The results showing the difference in the elevation values of the road surface indicate that the section, wherein the plastic deformation occurs throughout the entire road surface, can be identified and evaluated. With regard to flatness, in future studies, the long-directional elevation value of the target segment extracted using Global Mapper is likely to be derived from the International roughness index, which is the international flatness index used in the ProVAL program developed and used by the Federal Highway Administration. CONCLUSIONS : The road pavement status investigation conducted herein by utilizing drone-acquired images showed that repeated driving in a section is not required, and various analyses can be made in a single shot. If technologies, such as artificial intelligence, big data, and Internet of Things, which are the key components of the Fourth Industrial Revolution, are adapted, they can be used to investigate road pavement conditions and inspect completely constructed road lines and major road facilities.

PURPOSES : This study is aimed at developing an asphalt pavement material with high elasticity and watertight through mix design and laboratory tests. METHODS: High elastic (HE) asphalt modifier blended of thermoplastic elastomer, naphthene oil, mineral fiber and organic vulcanization accelerator was developed. Mix design was done to determine the aggregate gradation and optimum asphalt content for making high elastic and watertight asphalt mixture. Performance grade test of HE-modified asphalt binder as well as asphalt mixture tests, which include the tensile strength ratio test, Hamburg wheel tracking test, third-scale model mobile loading simulator(MMLS-3) test, four-point flexural fatigue test, and Texas reflection crack test were conducted to evaluate the characteristics of the HE-modified asphalt mixture. RESULTS: 7.7% optimum binder content was determined through the mix design, which met the quality criteria of Marshall asphalt mixture. The binder test indicated that the grade of the HE-modified asphalt was PG76-28. The results of the mixture tests indicated a tensile strength ratio of 0.92 and a rut depth of 6.2 mm at 20,000 cycles of Hamburg Wheel-Tracking Test. The asphalt mixture test also showed that the rut depth of HE-modified mixture was 39% less than that of Guss asphalt mixture. The crack resistance of the HE-modified mixture was 1.65 times higher than that of the Guss asphalt mixture from the Texas reflection crack test results. CONCLUSIONS: It can therefore be reasonable that HE-modified asphalt mixture is used as an intermediate layer in the asphalt overlay on concrete pavements. Additionally, the HE-modified asphalt mixture can be used for the asphalt pavement materials with high performance and watertight.

PURPOSES: The objective of this study is to evaluate the structural capacity of asphalt pavement in subsurface cavity sections using falling weight deflectometer (FWD) backcalculation method. METHODS: It is necessary to analyze the reduction of structural capacity in asphalt pavements due to the occurrence of subsurface cavities. The FWD testing was conducted on the cavity and intact asphalt pavement in the city of Seoul. The GAPAVE, backcalculation program for FWD deflections, was utilized to determine the layer moduli in asphalt pavements. The remaining life of asphalt pavements in cavity sections were predicted using the pavement performance model for fatigue cracking. The backcalculated layer moduli between cavity and intact sections were compared to determine the reduction of structural capacity due to subsurface cavity. The relationship between the reduction of layer modulus and cavity depth/length was analyzed to estimate the effect of cavity characteristics on the structural capacity degradation. RESULTS: According to the FWD backcalculation results, the modulus of asphalt layer, subbase, and subgrade in cavity sections are generally lower than those in intact sections. In the case of asphalt layers, the backcalculated modulus in cavity section was reduced by 50% compared to intact section. A study for the prediction of remaining life of cavity section shows that the occurrence of subsurface cavity induces the decrease of the pavement life significantly. It is found that there is no close relationship between the backcalculated modulus and cavity length. However, the reduction of asphalt layer modulus is highly correlated with the cavity depth and was found to increase with the decrease of cavity depth. CONCLUSIONS : This reduction of structural capacity due to the occurrence of cavities underneath asphalt pavements was determined using FWD backcalculation analysis. In the future, this approach will be utilized to establish the criteria of road collapse risk and predict the remaining life of cavity sections under numerous varied conditions.

PURPOSES: This study evaluated the effect of fog seal treatment utilizing an agricultural oil-based asphalt concrete sealant (ABCS) on the long-term performance of an asphalt pavement. METHODS: Fog seal treatment using ABCS was applied on 800 m of the pavement section in the test section with a total length of 2,400 m; the remaining pavement section was not considered for this treatment. A series of laboratory and field tests were conducted on both sections, including a Marshall stability test, penetration test, viscosity test, skid resistance test, and pavement surface macrotexture test. In addition, the pavement condition index (PCI) was determined 8 years after the ABCS application to evaluate the effect of the ABCS treatment on the pavement’s long-term performance. RESULTS : The ABCS-treated section exhibited a PCI of 75, whereas the non-treated section exhibited a value of 64. Furthermore, a MicroPAVERTM‚ pavement management system determined that the pavement deterioration rates (i.e., drops in PCI) were 3.6 and 5.1 per year for the ABCS-treated and non-treated sections, respectively. CONCLUSIONS : The results of the series of laboratory and field tests revealed that the ABCS treatment increased the pavement performance life by approximately 3.5 years.

PURPOSES: This paper presents the noise reduction effect of asphalt concrete pavement using steel slag aggregate. METHODS: Steel slag aggregates induce various mechanical effects because of their high stiffness and specific gravity. It is also known that the noise reduction effect is due to its high specific gravity and porous nature. In this study, the noise reduction in a steel slag asphalt concrete pavement section was measured and analyzed. RESULTS : On average, an asphalt concrete pavement with steel slag reduces road traffic noise by about 2 dB(A). In addition, the analysis of sound pressure levels by frequency showed lower sound pressure levels in steel slag asphalt concrete pavement than general HMA in all frequency ranges (from low to high frequencies). An analysis of the benefits with regard to noise, by assuming a road-traffic noise reduction of 2 dB(A) with asphalt concrete pavement using steel slag, shows that the noise abatement cost approach can save 1.6 million won a year over soundproof wall costs. In addition, the noise damage cost approach results in cost savings (with regard to noise) of between 19 and 60 million won per year depending on the population density. CONCLUSIONS: The use of steel slag aggregate as an asphalt concrete mixture material not only improves the mechanical performance but also has a noise reduction effect. It is expected that the steel slag asphalt concrete pavement can reduce the environmental burden by utilizing resources and provide a safer and more comfortable pavement condition to the road users.

PURPOSES : The purpose of this paper is to develop an evaluation method for aged reclaimed asphalt pavements using RAP mortar specimen and FTIR method. METHODS: To evaluate the low-temperature behavior of aged reclaimed asphalt pavements, an indirect tensile strength test was adopted with an RAP mortar specimen. The RAP mortar specimen without a rejuvenator was fabricated with two fine aggregate types as a function of passing sieve sizes. The fabricated RAP mortar specimen was frozen for 24 h at -20℃. The indirect tensile strength was measured as a function of different absolute viscosities. The indirect tensile strength and displacement were varied as functions of the dosage of the rejuvenator. The spectroscopy analysis of four asphalt binders was performed under attenuated total reflection. The four asphalt binders comprised of a virgin binder, two extracted RAP binders, and a mixed virgin and extracted RAP binder. To evaluate the oxidation of the binder, the carbonyl index was calculated. RESULTS : The four extracted RAP binders were measured with an extremely wide range of absolute viscosity from 30,000 poise to 170,000 poise. The indirect tensile strength of the RAP mortar decreased as the absolute viscosity increased. This means that at lower temperatures, the indirect tensile strength can indicate the oxidation of RAP. Also, the indirect tensile strength and displacement changed sensitively as the dosage of the rejuvenator was changed. Based on the FTIR principle, a good relation was observed between the dosage of the rejuvenator and the FTIR absorbance peak. It can be used to estimate the dosage of the rejuvenator in hot reclaimed asphalt mixture. Also, the carbonyl index of the RAP binder was calculated to evaluate asphalt oxidation using the FTIR principle. CONCLUSIONS : There is a good relation between the indirect tensile strength of RAP mortar and its absolute viscosity. This indicates that RAP mortar can be used to estimate the properties of aged RAP. Also, the usage of rejuvenator can be evaluated with both the indirect tensile strength and FTIR absorbance peak. The carbonyl index can be used to predict asphalt oxidation.

PURPOSES: Using recyclable materials in asphalt pavement industry is one of the essential tasks not only for saving construction budgets but also for mitigating environmental pollutions. Over the past decades, several efforts have been made by road maintenance agencies to incorporate various recyclable materials into virgin asphalt paving mixtures. As a result, reclaimed asphalt pavement (RAP), which consists of old pavement material was selected as one of most widely used recyclable materials. In this paper, the effects of using different amounts of single-recycled RAP (SRRAP) and double-recycled RAP (DRRAP) on the low-temperature characteristics of asphalt mixtures were investigated. METHODS: To evaluate the low-temperature characteristics of SRRAP and DRRAP mixtures, two experiments, the bending beam mixture creep test and semicircular bending fracture test were performed. The experimental parameters: creep stiffness, m-value, thermal stress, critical cracking temperature, fracture energy, and fracture toughness were computed then compared. RESULTS : RAP mixtures (SRRAP or DRRAP) showed lower mechanical performance compared with conventional asphalt mixtures. The differences became distinct with increased RAP addition. However, the performance differences between SRRAP and DRRAP mixtures were not significant in all cases, which indicate the possible application of re-recycling technology (DRRAP) in the asphalt pavement industry. CONCLUSIONS : The addition of RAP to virgin asphalt can mitigate low-temperature performance despite the improvement in fracture performance observed in some cases. Therefore, using RAP (SRRAP or DRRAP) mixtures on inter or sublayer construction, but not on the surface layer, is recommended. Moreover, the possibility of applying double-recycling technology in asphalt pavement industry can be introduced in this study because not significant performance differences were found between SRRAP and DRRAP mixtures especially at low temperature.

PURPOSES: Using recycled asphalt materials (called Reclaimed Asphalt Pavement: RAP) from existing asphalt pavement layers in newly constructed asphalt pavement is an essential option not only for lowering the construction budget but also for mitigating environmental pollution for society. For this reason, many pavement agencies in South Korea, the USA, and Canada have observed the effect of RAP on conventional asphalt pavement to evaluate and set proper material specifications and addable amounts. In this paper, effect of recyclable material on low-temperature performance of asphalt materials was investigated with two different mechanical tests. Among the recyclable material sources, RAP and Taconite Aggregate (TA), which is mainly produced in northern Minnesota (USA), were considered. METHODS : To evaluate the low-temperature mechanical performance of a RAP mixture, two different experimental tests (In-Direct Tensile (IDT) low temperature creep test and Semi-Circular Bending (SCB) test) were considered. The mechanical parameters creep-stiffness, relaxation modulus, fracture energy, and fracture toughness were computed then compared. RESULTS: More brittle characteristics were observed with RAP-added asphalt mixtures compared to the conventional asphalt mixtures, as expected. However, the differences of computed mechanical performances were not significantly distinct for RAP mixtures compared to conventional mixtures when the RAP proportion was around 20%, and with the addition of TA up to 20%. CONCLUSIONS : It can be concluded that up to 20% of RAP addition (along with TA up to 20%) in a virgin asphalt mixture does not provide significant performance reduction. This addable proportion can be viewed as a successful minimum level when considering the addition of RAP to hot-mix asphalt (HMA). Moreover, applying TA with RAP could offer a successful alternative for asphalt recycling and the materials industry.

PURPOSES: The objective of this study was to develop an asphalt pavement response model for a subsurface cavity section using the 3D finite element method and a statistical approach. METHODS: It is necessary to analyze the structural behavior of asphalt pavement with a subsurface cavity to evaluate the degree of risk for a road cave-in. A 3D finite element model was developed to simulate the subsurface cavity underneath asphalt pavement and was verified using the ILLIPAVE program. Finite element analysis was conducted for asphalt pavement sections with different asphalt layer thickness/modulus, and cavity depth and length, to generate the artificial pavement response database. The critical pavement response considered in this study was the tensile strain at the bottom of the asphalt layer because fatigue cracking is the main cause of road cave-in. The relationship between the critical pavement response and influencing factors was investigated using the pavement response database. The statistical regression approach was adopted to develop the asphalt pavement response model for predicting the critical pavement response of asphalt pavement with a subsurface cavity. RESULTS : It was found from the sensitivity analysis that the asphalt layer thickness or modulus, and cavity depth or length, are the major factors affecting road cave-in incidents involving asphalt pavement. The asphalt pavement response model showed high accuracy in predicting the tensile strain at the bottom of asphalt layer. It was found from the verification study that the R square value between finite element model and pavement response model were 0.969 and 0.978 in the cavity and intact sections, respectively. CONCLUSIONS: The work reported in this paper was intended to figure out the pavement structural behavior and to develop a pavement response model for the occurrence of cavities underneath asphalt pavement using 3D finite element analysis. In the future, critical pavement response will be utilized to establish the criteria of risk of road cave-in based on various different conditions.