The properties and electrochemical characteristics of anode material using pitch-coated graphite residue compounds by heat-treatment at 600℃ for 1 hour were investigated. The distance of layers of pitch-coated graphite residual compounds was 3.3539 a, which was as same as that of graphite. Its electrochemical and charge discharge characteristics were tested according to different four types of carbon material, natural graphite, pitch-coated graphite, amorphous graphite and pitch-coated graphite residual compounds, respectively. So it was shown the best charge-discharge characteristics in all of the samples. For the electrochemical and charge-discharge characteristics, although pitch-coated graphite residual compounds had different carbon contents 70% and 80%, these two samples were shown good electrochemical and charge-discharge characteristics.

2000년 3월부터 2000년 11월까지 공주시 근교의 리기다소나무림에서 계절별 버섯의 출현종과 종별 개체수, 생산량 및 영양염류 함량을 조사하였다. 조사기간 중 영구방형구 내에 출현한 종은 총 32종류이었다. 버섯은 6월부터 출현하기 시작하여 9월에 종다양성과 생산량이 가장 높았다. 월별 우점종은 6월과 7월에는 밀버섯, 8월과 9월은 갈색털꾀꼬리버섯 이었으며, 10월에 젖버섯아재비버섯을 끝으로 더 이상 출현하지 않았다. 연중 가장 많은 개체수를 보인

In this study, commercially available pitch-based carbon fibers of general grade were post-heat-treated using a boxtype high temperature furnace at 1800℃, 2000˚, 2200℃, and 2400℃, respectively. The fundamental characteristics of each heat-treated carbon fibers were investigated in terms of chemical composition, morphology, thermal stability, X-ray diffraction, single filament tensile test, and electrical resistivity. The result showed that the fiber properties were significantly influenced by the post-heat-treatment, indicating the greater effect with increasing treatment temperature. The carbon contents, thermal stability, and tensile properties of the carbon fibers used here were further increased by the post-heat-treatment, whereas the d-spacing between graphene layers and the electrical resistivity were reduced with increasing post-heat-treatment temperature.

Carbon/TiO2 composites were prepared by CCl4 solvent mixing method with different mixing ratios. Since the carbon layers derived from pitch on the TiO2 particles were porous, the Carbon/TiO2 composite series showed a good adsorptivity and photo decomposition activity. The BET surface area for the carbon layer in the sample increases to increasing with pitch contents. The SEM results present to the characterization of porous texture on the Carbon/TiO2 composite and pitch distributions on the surfaces for all the materials used. From XRD data, a weak and broad carbon peak of graphene with pristine anatase peaks were observed in the X-ray diffraction patterns for the Carbon/TiO2. The EDX spectra show the presence of C, O and S with strong Ti peaks. Most of these samples are richer in carbon and major Ti metal than any other elements. Finally, the excellent photocatalytic activity of Carbon/TiO2 with slope relationship between relative concentration (C/C0) of MB and t could be attributed to the homogeneous coated pitch on the external surface by CCl4 solvent method.

Isotropic pitch-based carbon fiber has been activated by steam diluted in nitrogen in order to characterize the microporosity. Especially, 40 wt% burn-off ACFs were prepared from different conditions to compare the pore structure and size. The ACFs were thinly sliced to investigate the inside pores by TEM and image analyzer. As expected, the adsorption characteristics of these ACFs were quite different from one another because of different pore structure and size. Most pores are not slit-shaped but rather round. Small round micropores become broad and irregular as increasing the activation time and temperature.

본 연구에서는 고준위 방사성폐기물 심지층 처분시설의 규모 및 layout설정에 필요한 요소인 처분터널 및 처분공 간격에 대한 분석을 수행하였다. 이를 위하여, 기준 처분개념과 공학적 방벽 개념을 바탕으로 다양한 조건의 처분터널 및 처분공 단면을 설정하고, 단층 배치 및 복층 배치 개념 에 따른 처분동굴의 구조적, 열적 안정성을 분석하였다. 분석 결과를 바탕으로 설계에 있어서 주요한 고려인자 중의 하나인 굴착량을 감소시킬 수 있는 처분동굴 및 처분공 간격을 제안하였다. 본 연구의 결과는 심지층 처분시설 설계시 활용될 것이며, 향후, 부지에 대한 불확실성을 줄이기 위하여 정확한 부지특성 자료를 통한 상세한 분석이 필요하다.

In this study, AR (aromatic resin) pitch was employed as the matrix-precursor for carbon/carbon composite because it exhibits much higher coke yield than coal tar pitch. As a result, a fabrication process of carbon/carbon composites can be shortened. It has been known that the pitches may cause swolling problem during the carbonization process. In order to restrain the swelling occurrence, a small quantity of carbon black was added to the AR pitch. Due to addition of carbon black the swelling was decreased largely and the perform can be infiltrated with the AR pitch. The densification efficiency of the performs was compared with various matrix-precursors. The coke yield of matrixprecursors, the morphology and the degree of graphitization of carbon matrix were analyzed.

MCMB (Mesocarbon microbeads) is a kind of anode material for lithium-ion secondary battery. MCMB charge/discharge cycle stability is one of the important criterion at lithium-ion battery operation. In this study, the cycling stability of a lithium-ion secondary battery has been examined. MCMB was made by the direct solvent extraction method. After the MCMB was carbonized and graphitized, the measurement of charge/discharge capacity and efficiency were carried out. In the result, discharge capacity of MCMB in the initial cycle was above 290.0 mAh/g. After the second cycle, efficiency of charge/discharge MCMB was about 98%. These results were similar to the commercial MCMB product.

Structural changes of high modulus carbon fiber by oxidation in carbon dioxide gas using SEM, TEM, and XRD have been observed. It was shown that the originally high modulus carbon fiber is composed of highly ordered graphitic crystalline area and non-crystalline area. It was observed that the La increases during the whole oxidation process. It was shown that the oxidation of high modulus carbon fiber initiates at the non-crystalline area and at the ends of fiber. The large pores developed in fiber by direction of fiber length at high temperature (1,100℃), and the small pores developed on the fiber surface at low temperature (900℃). In conclusion, it is found that the oxidation of the carbon fiber was progressed through the imperfection.

A study of partial carbonisation of green pitch fibres to temperatures in the range of 500-1000℃ was carried out on three precursors - a neat pitch and two polymer modified pitches, with a view to find out a suitable temperature at which the fibres acquire considerably improved toughness or handleability (compared to that in the green stage) for their subsequent processing into carbon fibres. A partial carbonisation temperature of 500-600℃ has been identified to result in a remarkable improvement in the toughness/handleability of the fibres in all the three cases. However, from techno-economical considerations, the neat pitch appears to provide the best precursor system for the production of pitch based carbon fibres.

Two types of carbon fiber based high modulus- and isotropic-pitch were exposed to isothermal oxidation in air and CO2 gas and the weight change was measured by TGA apparatus. The kinetic equation was introduced f=1--(-atb) and the constant b was obtained in the range of 1.02~1.68 for the isotropic fiber and obtained 0.91~1.93 for the high modulus fiber respectively. In considering the effect of the atmosphere for isothermal oxidation, the value of the constant b obtained in the carbon dioxide was higher than that obtained in the air. Therefore, it was found that the pitch based carbon fiber shows sigmoidal characteristic when it is oxidized in the carbon dioxide. In addition, it was also found that kf = 0.5, which was reaction constant at f = 0.5, was a very useful parameter for evaluation of the oxidation reactivity of pitch based carbon fibers. According to the consideration, it is suggested that the conversion-time curves of the pitch based carbon fibers are correlated by normalized equation f=1--(-AτB), where τ=t/tf= 0.5.

MCMB (mesocarbon microbeads) has been synthesized from coal tar pitch, petroleum pitch and polymer compound generally. But yield of MCMB was low about 20~40 wt% and was not above 50 wt%. Neither MCMB was replaced with natural graphite because of economic performance, refining MCMB, and control of the particle size distribution. This study was performed to elevate yield of MCMB and to develop technique of particle size distribution. As the result, yield of MCMB that was synthesized from coal tar pitch increased more than 60 wt% about raw material and particle size of MCMB was restrained according to control of QI (quinoline insoluble) ingredient in raw pitch, heat treatment temperature and time.

Activated carbon fibers were prepared from the petroleum isotropic pitch and organometallic compounds. The metals were dispersed uniformly in the ACFs. The specific surface area and pore size distributions of metal containing ACFs were measured. The mesopores of ACFs were developed by Co, Ni, and Mn metals addition, and the catalytic reactivity of ACFs' SOx removal was increased by adding Ni and Pd metals. It was found that the mesopores did not work forthe improvement of catalytic reactivity of ACFs' SOx removal with the blank experiment using the metal removed ACFs.

Short pitch fibers were prepared from petroleum based isotropic precursor pitch by melt-blown technology. The pitch fibers were stabilized in oxidizing condition, followed by steam activations at various conditions. The fiber surface and pore structures of the activated carbon fibers (ACFs) were respectively characterized by using SEM and applying BET theory from nitrogen adsorption at 77 K. The weight loss of the oxidized fiber was proportional to activation temperature and activation time, independently. The adsorption isotherms of the nitrogen on the ACFs were constructed and analyzed to be as Type I consisting of micropores mainly. The specific surface area of the ACFs proportionally increased with the weight loss at a given activation temperature. The specific surface area was ranged 850~1900 m2/g with pores of narrow distribution in sizes. The average pore size was ranged 5.8~14.1 a with the larger value from the more severe activation condition.

The surface treatment of C-type isotropic pitch-based carbon fiber was carried out by anodic oxidation in 5 wt% NH4NO3 electrolyte. The changes of fiber surface and carbon fiber/ABS resin composites were characterized by SEM, XPS and mechanical properties test. The oxygen functional groups on the surface, such as hydroxyl (-C-OH), carboxyl (-COOH) groups etc., increased after oxidation. Tensile strength, flexural strength and modulus of carbon fiber/ABS composites were also enhanced. However, the impact strength decreased with the improvement of the surface adhesion between CF and matrix.

Petroleum based isotropic pitch was spun into short fiber by melt-blown spinning technology. The processing parameters chosen were air velocity, die temperature, and throughput rate of the pitch within the ranges of experimental tolerances. The fiber diameter was reduced to 6μm by increases of hot air velocity, and spin die temperature. Also, the fiber diameter was strongly dependent on the throughput rate of the pitch and jet speed of hot air through the spinnerets. Even fibers with 10μm diameter were produced at throughput rate of 0.17g/min·hole and at die temperature of 290℃.

Quinoline insoluble formed by the heat treatment was hot-pressed near its softening point. The green body was stabilized in the temperature range of 300~400℃ and subsequently carbonized below 1300℃ in an argon atmosphere. The behaviors of QI formation was examined with varying the heat treatment temperature and the lapse of time of the sample carbonized at various temperatures. And the mechanical property, corrosion resistance, and friction behavior were also measured optimum content of mesophase pitch ensured a dense structure and high LC(002) value, which resulted in high mechanical properties, good corrosion resistance, and low-stable friction behavior.

A series of activated carbons were prepared from coconut shells and coal-tar pitch binder by physical activation with steam in this study. The effect of variable processes such as activation temperature, activation time and ratio of mixing was investigated for optimizing those preparation parameters. The activation processes were carried out continuously. The nitrogen adsorption isotherms at 77 K on pellet-shaped activated carbons show the same trend of Type I by IUPAC classification. The average pore sizes were about 19-21a. The specific surface areas (SBET) of pellet typed ACs increased with increasing the activation temperature and time. Specific surface area of AC treated for 90 min at temperature 900℃ was 1082 m2/g. The methylene blue numbers continuously increased with increasing the activation temperature and time. On the other hand, iodine numbers highly increased till activation time of 60 min, but the rate of increase of iodine numbers decreased after that time. This indicates that new micropores were created and the existing micropores turned into mesopores and macropores because of increased reactivity of carbon surface and H2O.