Recently, steel dampers are widely used as seismic reinforcement devices. Steel dampers have the advantage of being easy to manufacture and being able to absorb a lot of energy through stable hysteresis behavior. However, there is a possibility that the steel damper may be damaged due to fatigue caused by repeated seismic loads. In this study, the seismic performance of steel dampers and engineering plastic dampers with different physical characteristics were compared and analyzed. In addition, numerical analysis was performed on a hybrid damper that combines a steel damper and an engineering plastic damper. It is more effective to apply engineering plastic dampers to structures that experience significant displacement due to seismic loads. The behavior of hybrid dampers combining steel dampers and engineering plastic dampers is dominated by steel dampers. A hybrid damper in which an engineering plastic damper yields after a steel damper yields can effectively respond to various seismic loads and secure high ductility and excellent seismic performance.

The precast-buckling restrained braces(PC-BRB) reinforced with engineering plastics that can compensate for the disadvantages in the manufacturing process of the existing buckling restrained brace. In this study, to examine the applicability of PC-BRB to actual structures, example structures similar to school facilities were selected and the reinforcement effect was analyzed analytically according to the damping design procedure of PC-BRB. Load-displacement curve through the incremental loading test appeared similar to the bilinear curve. Applying test result, Analytical model of PC-BRB model was constructed and applied to the example structure. As a result of the analysis, the PC-BRB showed stable hysteresis behavior without lowering the strength, and the inter story drift ratio and the shear force were reduced due to the damping effect. In addition, the reduction ratio of the shear force was similar to the reduction ratio assumed when designing the damping device.

In this study, the Buckling restrained braces reinforced with engineering plastics that can compensate for the disadvantages in the manufacturing process of the existing buckling restrained brace. The proposed PC-BRB was fabricated to evaluate the reinforcement effect by carrying out a structural performance test and a full-scale two-layer frame test through cyclic loading test. As a result of PC-BRB's incremental and cyclic loading test, stable hysteresis behavior was achieved within the target displacement, and the compressive strength adjustment coefficient satisfied the recommendation. As a result of the real frame experiment, the strength of the reinforced specimen increased compared to the unreinforced specimen, and the ductility and energy dissipation increased.

The fatigue characteristics of glass fiber reinforced plastic (GFRP) composites were studied under repeated loads using the finite element method (FEM). To realize the material characteristics of GFRP composites, Digimat, a mean-field homogenization tool, was employed. Additionally, the micro-structures and material models of GFRP composites were defined with it to predict the fatigue behavior of composites more realistically. Specifically, the fatigue characteristics of polybutylene terephthalate with short fiber fractions of 30wt% were investigated with respect to fiber orientation, stress ratio, and thickness. The injection analysis was conducted using Moldflow software to obtain the information on fiber orientations. It was mapped over FEM concerned with fatigue specimens. LS-DYNA, a typical finite element commercial software, was used in the coupled analysis of Digimat to calculate the stress amplitude of composites. FEMFAT software consisting of various numerical material models was used to predict the fatigue life. The results of coupled analysis of linear and nonlinear material models of Digimat were analyzed to identify the fatigue characteristics of GFRP composites using FEMFAT. Neuber’s rule was applied to the linear material model to analyze the fatigue behavior in LCF regimen. Additionally, to evaluate the morphological and mechanical structure of GFRP composites, the coupled and fatigue analysis were conducted in terms of thickness.

유한요소법(finite element method)은 다양한 분야에서 재료의 역학적 거동을 더욱더 현실적으로 해석하고 예측하는 방법으로 다양한 분야의 제품 개발에 적용되고 있다. 하지만 섬유배향과 변형률 속도가 역학적 특성에 영향을 미치는 유리섬유 강화 플라스틱 복합재료에 관한 수치해석을 이용한 접근 방법은 현재까지 다소 어려움이 있다. 본 연구의 목적은 고분자, 고무, 금속 등과 같은 다양한 복합재료를 위한 선형, 비선형 다중스케일 재료 모델링 프로그램인 Digimat의 수치해석 재료 모델을 활용하여 유리섬유 강화 플라스틱 복합재료의 역학적 특성을 정의하고 검증하는 것에 있다. 또한 이를 통해 좀더 현실 적으로 고분자 복합재료의 거동을 예측하고자 한다. 이를 위해 다양한 고분자 중 30wt%의 단섬유 질량 비율을 갖는 폴리부 틸렌 텔레프탈레이트(polybutylene terephthalate, PBT)의 섬유배향과 변형률 속도에 따른 인장 특성을 참고문헌을 통해 조사하였다. 또한 Moldflow 프로그램을 사용한 사출해석을 통해 유리섬유 배향 정보를 계산하였으며 이를 매핑(mapping) 과 정을 통해 유한요소 인장 시편 모델에 전달하였다. 대표적인 유한요소 상용 프로그램 중 하나인 LS-DYNA는 유리섬유 배향과 변형률 속도에 따른 복합재료의 인장 특성을 연구하기 위해 Digimat과의 연성해석(coupled analysis)에 활용되었다. 그리고 유리섬유 강화 플라스틱 복합재료를 해석하기 위한 LS-DYNA의 다양한 비등방성(anisotropic) 재료 모델들의 장단점을 서로 비교하고 평가하였다.

A pultruded fiber reinforced polymer plastic (PFRP) structural is one of the most widely used composite member in construction. In generally, PFRP members is composed of plate elements so that it needs to evaluate stability problems when they are used by construction members. On the other hand, creep effect may be occurred in PFRP members under sustained load. Primary to experiment for PFRP creep, previous works are studied. In the previous work related to buckling of PFRP member, it can be calculated buckling strength of PFRP members when it is known that material property of longitudinal and transverse direction of PFRP members. The researches for creep behavior of PFRP has been conducted and time-dependent degradation elastic moduls can be predicted by the empirical equation. In this study, it will be conducted creep test for PFRP and time-dependent stress-strain relationship will be plotted. It is expected that long-term buckling behavior of PFRP is evaluated by theoretical and numerical method such as finite element method.

Warpage of injection molded product is caused by non-uniform shrinkage and residual stress. A method of removing uneven molding shrinkage and residual stress is to remove the defective factor to Uniform cooling of products. Warpages for part designs have been investigated in this study according to the injection molding conditions for amorphous ABS and crystalline PP by the rapid cooling and heating system. Experimental results showed that the crystalline resin was more warped than amorphous resin, Warpages have been observed in the regions of the part, near gate region and flow direction region.

Rapid industrial development in recent times has increased the demand for light-weight materials with high strength and structural integrity. In this context, carbon fiber-reinforced plastic (CFRP) composite materials are being extensively used. However, laminated CFRPs develop faults during impact because CFRPs are composed of mixed carbon fiber and epoxy. Moreover, their fracturing behavior is very complicated and difficult to interpret. In this paper, the effect of the direction of lamination in CFRP on the absorbed impact energy and impact strength were evaluated, including symmetric ply (0°/0°, –15°/+15°, –30°/+30°, –45°/+45°, and –90°/+90°) and asymmetric ply (0°/15°, 0°/30°, 0°/45°, and 0°/90°), through drop-weight impact tests. Further, the thermal properties of the specimens were measured using an infrared camera. Correlations between the absorbed impact energy, impact strength, and thermal properties as determined by the drop-weight impact tests were analyzed. These analyses revealed that the absorbed impact energy of the specimens with asymmetric laminated angles was greater than that of the specimens with symmetric laminated angles. In addition, the asymmetry ply absorbed more impact energy than the symmetric ply. Finally, the absorbed impact energy was inversely proportional to the thermal characteristics of the specimens.

This study was developed the rapid heating and cooling device using peltier module for uniform cooling. make the rapid heating and cooling device(RCHD), for traditional water cooling device(TWCD) method and the rapid heating and cooling method warpage were compared and were analyzed and the materials used crystalline PP polymer. various warpage were compared for the process parameters such as packing pressure, packing time, mold temperature. in the crystalline PP polymer, TWCD method has higher warpage than RCHD method and show the result to be a bit more uniform cooling. RCHD method has higher warpage than TWCD method as cooling time and packing time increases and TWCD method has higher warpage than RCHD method as mold temperature increases.

In general, it is required mechanical properties and strength tests to use the material in engineering applications. The material fringe values of photoelastic materials vary with the supplier, the batch of resin, temperature and age, it is necessary to calibrate each of sheet of photoelastic material at the time of the test. In this paper, we perform tensile tests and calibrations tests for photoelastic stress fringe constant in order to obtain the mechanical properties of materials and photoelastic material fringe constants of PMMA and PSM-1. From this tests, the tensile strength of PMMA and PSM-1 were 100.5 MPa and 71.5 MPa, respectively. Also, the measured material stress fringe constants of PMMA and PSM-1 were 13.33 N/mm and 6.91 N/mm, respectively.

국내 유통 중인 총 321건의 폴리아미드, 폴리우레탄, ABS, 아크릴 수지 재질 식품용 기구 중 이행우려가 있는 모노머인 4,4``-메틸렌디아닐린, 2,4-톨루엔디아민, 아닐린, 아크릴로니트릴 및 메틸메타크릴레이트에 대하여 이행량 을 조사하고 안전성 평가를 실시하였다. 83건의 폴리아미드, ABS 및 아크릴 수지 재질 식품용 기구 검체에서 현행 식품용 기구 및 용기·포장 공전상의 용출규격 이하인 4,4``-메틸렌디아닐린, 2,4-톨루엔디아민, 아크릴로니트릴 및 메틸메타크릴레이트가 이행되었다. 이행량 결과를 토대로 안전성 평가 시나리오에 적용하여 4,4``-메틸렌디아닐린, 2,4-톨루엔디아민, 아크릴로니트릴 및 메틸메타크릴레이트의 EDI를 산출한 후 TDI와 비교하여 위해도를 평가하였다. EDI는 폴리아미드 재질 기구의 4,4``-메틸렌디아닐린과 2,4-톨루엔디아민의 경우 각각 2.39 × 10-9, 및 1.20 × 10-9mg/kg bw/day, ABS 재질 기구의 아크 릴로니트릴의 경우 4.32 × 10-9mg/kg bw/day, 아크릴 수지 재질 기구 메틸메타크릴레이트의 경우 2.27 × 10-7mg/kg bw/day이었다. ABS 재질 기구 이행 아크릴로니트릴의 위해도는 RfD 대비 4.32 × 10-4% 수준이었고, 아크릴 수지 재질 기구 이행 메틸메타크릴레이트의 위해도는 TDI 대비 1.89 × 10-5% 수준이었다. 결론적으로 검토된 평가 항목들의 위해도는 TDI 대비 4.32 × 10-4%와 1.89 × 10-5%에 불과한 것으로 조사되어 안전한 수준인 것으로 사료되었다. 이러한 결과들은 앞으로 기구 및 용기·포장의 안전 관리를 위한 과학적인 근거자료로 이용될 수 있을 것으로 판단된다.

국내 유통 중인 총 391건의 유리제, 도자기제, 법랑, 옹기류, 폴리에틸렌제 및 폴리프로필렌제 식품용 기구 및 용 기·포장 중 이행 우려가 있는 납, 카드뮴, 비소, 안티몬, 6가크롬 및 수은에 대하여 이행량을 조사하고 안전성 평가를 실시하였다. 29건의 도자기제 및 법랑 검체에서 현행 식품용 기구 및 용기·포장 공전상의 용출규격 이하인 납, 카드뮴 및 안티몬이 이행되었다. 이행량 결과를 토대로 안전성 평가 시나리오에 적용하여 이행된 납, 카드뮴 및 안티몬의 EDI를 산출한 후 TDI와 비교하여 위해도를 평가하였다. 도자기제 기구 이행 납 및 카드뮴의 위해도는 TDI 대비 0.25%, 0.11% 수준이었고 법랑 기구 이행 납, 카드뮴 및 안티몬의 위해도는 TDI 대비 0.33%, 1.52% 및 0.13% 수준이었다. 결론적으로 검토된 평가 항목들의 위해도는 TDI 대비 최대 1.52%에 불과한 것으로 조사되어 안전한 수준인 것으로 사료되었다. 이러 한 결과들은 앞으로 기구 및 용기·포장의 안전관리를 위한 과학적인 근거자료로 이용될 수 있을 것으로 판단된다.

본 연구에서는 자연분해재 펠릿과 polyethylene들을 이용해 LDPE와 신장율과 인장강도가 유사한 생붕괴성 플라스틱 필름들을 제조하였다. 식품 포장재로서의 안전성, 광분해성, 열분해성 및 곰팡이 생분해성을 평가한 결과 제작된 생붕괴성 플라스틱 필름들은 식품 포장재로 사용하기에 안전하고 LDPE 필름에 비해 상대적으로 우수한 분해 특성을 나타내어 환경친화적인 식품 포장 소재로 사용될 가능성을 보여주었다.

통영, 인천, 군산 및 홍성의 해수 미생물에서 각종 어업용구의 재료로 사용될 수 있는 Mater-Bi®, PHBV, PBSA 및 PCL의 분해거동을 조사하였다. Acinetobacter lwoffu/junii와 Shewanella algae/putrefaciens는 모든 해수속에 서식하고 있었으며 Eikenella corrodens 역시 비록 YITEK 결과의 신뢰도가 조금 낮은 수준으로 동정되었지만 모든 해수에서 검출되었다. 해수에서는 M

M390 microclean(R) of Edelstahl is a powder metallurgical plastic mould steel with a high level of corrosion and wear resistance and therefore often used in the plastics processing industry. But as a consequence of rapidly advancing developments in the plastics processing industry the required level of wear resistance of tool steels in this field is constantly rising. For that reason a new PM tool steel with higher hardness values and an increased amount of primary carbides has been developed to improve the resistance against abrasive and adhesive wear. The wear resistance of both steels against adhesive situations for components of the plastification unit of injection moulding machines has been tested with a novel method. In case of processing polyolefins with an injection moulding machine it was found that there is adhesive wear between the check-ring and the flights of the screw tip of the non-return valve under certain circumstances. The temperature in that region was measured with an infrared temperature sensor. The existence of significant peaks of that signal was used as an indicator for an adhesive wear situation.