강재를 대처할 수 있는 다양한 복합재료 중 CFRP (Carbon Fiber Reinforced Polymer)를 사용하여 인장 물성 실험을 실시한다. KS F ISO 10406 (콘크리트용 섬유강화 폴리며(FRP 보강재 - 시험방법) 에서 FRP의 측정길이는 지름 (D)의 40 배를 기준으로 제시되어진다. 그러나 25 mm 이상의 시험체는 양단 보강부를 포함하게 된다면 대략 2 m 이상으로 제작되어지게 되고 시험이 상당히 번거롭게 됨으 로써 시험법 개선을 위해서 측정 길이별로 설정하여 성능평가 후 비교분석 한다.

미세구조 특성의 불확실성은 재료 특성에 많은 영향을 준다. 시멘트 기반 재료의 공극 분포 특성은 재료의 역학적 특성에 큰 영향을 미치며, 재료에 랜덤하게 분포되어 있는 많은 공극은 재료의 물성 예측을 어렵게 한다. 공극의 특성 분석과 재료 응답 간의 상관관계 규명에 대한 기존 연구는 통계적 관계 분석에 국한되어 있으며, 그 상관관계가 아직 명확히 규명되어 있지 않다. 본 연구에서는 합성곱 신경망(CNN, convolutional neural network)을 활용한 이미지 기반 데이터 접근법을 통해 시멘트 기반 재료의 역학적 응답을 예측하 고, 공극분포와 재료 응답의 상관관계를 분석하였다. 머신러닝을 위한 데이터는 고해상도 마이크로-CT 이미지와 시멘트 기반 재료의 물성(인장강도)로 구성하였다. 재료의 메시 구조 특성을 분석하였으며, 재료의 응답은 상장균열모델(phase-field fracture model)에 기 반을 둔 2D 직접 인장(direct tension) 유한요소해석 시뮬레이션을 활용하여 평가하였다. 입력 이미지 영역의 기여도를 분석하여 시편 에서 재료 응답 예측에 가장 큰 영향을 미치는 영역을 CNN을 통하여 식별하였다. CNN 과정 중 활성 영역과 공극분포를 비교 분석하 여 공극분포특성과 재료 응답의 상관관계를 분석하여 제시하였다.

The use of hanging scaffolding for exterior wall painting and cleaning in building construction and maintenance carries the inherent risk of fall accidents. While periodic rope replacement is crucial for preventing accidents resulting from rope breakage, current regulations lack specificity in determining appropriate disposal period for fiber ropes. This study analyzed the tensile strength of the most commonly used PP fiber ropes with different diameters (16 mm, 20 mm) in the domestic construction industry. Additionally, the effect of outdoor exposure was examined by measuring the tensile strength of new ropes and ropes exposing to outdoor conditions for 30 days and 90 days. The results showed that the new ropes and those exposed to outdoor for 30 days met the KS (Korean Standards) criteria for tensile strength. However, a significant decrease in tensile strength was observed in ropes exposed to outdoor for 90 days compared to both the new ropes and those exposed for 30 days. Furthermore, the ropes exposed for 90 days did not meet the KS criteria. These findings indicate the degradation of PP fiber ropes due to UV (Ultra Violet) radiation, highlighting the importance of considering this factor when determining the replacement period for fiber ropes used in scaffolding work.

In this paper, the CFRP(Carbon Fiber Reinforced Plastic) parts were printed and cut in a large-scale additive and subtractive hybrid manufacturing system. A method to increase the strength and durability of a product by identifying the interlayer adhesion during the printing process of a large-scale additive manufacturing hybrid system was investigated. According to the printing conditions(CF content, deposition temperature, compaction process), the specimen was printed and cut to determine the tensile strength in the printing direction. As a result of the experiment, the highest tensile strength was shown when ABS-CF 20wt.% Compound was printed at 230℃ extrusion temperature, and the higher the CF content of the material, the lower the tensile strength. As a result of observing the inside of the test piece through an optical microscope, a large number of voids were kept inside the test piece. To remove voids generated inside the test piece, a compaction process was applied to the additive manufacturing hybrid system to prepare a test piece. As a result, void size decreased, and the strength of the part showed a tendency to increase. It is thought that additive manufacturing with high tensile strength can be obtained through studies on the optimization of deposition conditions in additive manufacturing hybrid systems.

PURPOSES : The aim of this study is to evaluate the effects of air voids, binder content, and aggregate gradation on the indirect tensile strength (IDT) and cracking tolerance index (CTindex) of cored asphalt pavements. METHODS : Cored samples were obtained from roads in Incheon city, and several laboratory experiments were performed. First, the cored samples were first to cut into a size appropriate for the IDT test. Subsequently, the air voids of the samples were measured. The damaged sample from the IDT test was loose mixed at 150 ℃ before the binder content was determined, which was conducted via an asphalt extraction test. Finally, the clean aggregates obtained from asphalt extraction process were analyzed in the aggregate gradation test. RESULTS : The result shows that an increase in air voids from 4% to 8% decreases the IDT and cracking tolerance index (CTindex) by 30% and 28%, respectively. Incorporating a binder enhances the ductile behavior of the asphalt mixture, resulting in a higher CTindex. Finally, the contribution of the aggregate grade on the IDT and CTindex is negligible. CONCLUSIONS : The IDT and CTindex are primarily affected by the air voids and binder content. A higher percentage of air voids results in a lower IDT. In addition, a higher amount of binder increases the IDT and CTindex of the cored samples. Meanwhile, the aggregate grade does not affect the IDT.

Recently, 3D printing has been actively studied. A representative material in this 3D printing technology is plastic, and PLA, an eco-friendly material, is widely used. FDM is widely used as a way to output these PLA materials. However, this method lacks mechanical properties compared to injection-molded products as it is a method of stacking materials by melting. Therefore, in this study, using an FDM-type 3D printer, a tensile test was performed after printing a tensile specimen with PLA filament with the layer angle and layer density as control factors. After that, changes in tensile properties according to the layer angle and density were compared and evaluated. As a result, to improve the tensile strength, the layer density had to be considered, and to improve the elastic modulus, both the layer angle and the layer density had to be considered.

콘크리트 경화 시 발생하는 수분증발로 인한 건조수축은 콘크리트의 균열을 발생시킨다. 콘크리트에 발생하는 균열 은 콘크리트의 내구성을 저하하여 안정성과 사용성에 문제를 발생시킨다. 이러한 문제점을 보안하기 위해 콘크리트에 강섬유를 혼입하여 건조수축으로 인한 균열을 방지하는 강섬유 보강 콘크리트 (SFRC)에 관한 연구가 진행되고 있다. 강섬유는 콘크리트 의 균열단면에서 가교역할, 부착작용을 통해 건조수축으로 인한 균열발생을 억제하고 균열 폭을 감소시키는 효과가 있다. 본 논 문에서는 강섬유의 인장강도에 따른 강섬유 보강 콘크리트의 건조수축 제어성능을 평가하였다. 자유건조수축 실험과 구속건조 수축 실험을 진행하였으며 실험 결과를 콘크리트의 인장응력으로 변환하여 콘크리트 직접인장실험 결과와 비교하였다. 강섬유 의 자유건조수축 저감 효과는 미미하지만 강섬유의 인장강도가 증가할수록 구속건조수축으로 인한 균열제어에 효과적임을 확인 하였다. 또한 강섬유의 인장강도가 증가할수록 콘크리트의 인장응력이 증가함을 확인하였다.

We fabricate the non-equiatomic high-entropy alloy (NE-HEA) Fe49.5Mn30Co10Cr10C0.5 (at.%) using spark plasma sintering under various sintering conditions. Each elemental pure powder is milled by high-energy ball milling to prepare NE-HEA powder. The microstructure and mechanical properties of the sintered samples are investigated using various methods. We use the X-ray diffraction (XRD) method to investigate the microstructural characteristics. Quantitative phase analysis is performed by direct comparison of the XRD results. A tensile test is used to compare the mechanical properties of small samples. Next, electron backscatter diffraction analysis is performed to analyze the phase fraction, and the results are compared to those of XRD analysis. By combining different sintering durations and temperature conditions, we attempt to identify suitable spark plasma sintering conditions that yield mechanical properties comparable with previously reported values. The samples sintered at 900 and 1000oC with no holding time have a tensile strength of over 1000 MPa.

Methods for predicting the ultimate/buckling strength of ship structures have been extensively improved in terms of design formulas and analytical solutions. In recent years, the design strategy of ships and offshore structures has tended to emphasize lighter builds and improve operational safety. Therefore, the corresponding geometrical changes in design necessitate the use of high-tensile steel and thin plates. However, the existing design formulas were mainly developed for thick plates and mild steels. Therefore, the calculation methods require appropriate modification for new designs beased on high-tensile steel and thin plates. In this study, a modified formula was developed to predict the ultimate strength of thin steel plates subjected to compressive and shear loads. Based on the numerical results, the effects of the yield stress, slenderness ratio, and loading condition on the buckling/ultimate strength of steel plates were examined, and a newly modified double-beta parameter formula was developed. The results were used to derive and modify existing closed-form expressions and empirical formulas to predict the ultimate strength of thin-walled steel structures.

A carbon fiber reinforced thermoplastic (CFRTP) was irradiated with a high energy electron-beam. As a result, the tensile strength of high-density polyethylene (HDPE)-based CFRTPs was significantly improved by gradually increasing the electron-beam dose. It was confirmed that the adhesion between CF and HDPE was improved and the surface properties of CF and HDPE were readily modified by electron-beam. It was verified from spectroscopic analysis that various oxygencontaining functional groups were formed on the surface of CF and HDPE by irradiation and we believe that strong attractive interactions took place among these functional groups at the interface of CFs and HDPE. Finally, it was conclusive that electron-beam irradiation provided two main effects on CFRTPs. One was cross-linking of thermoplastic resin for efficient load transfer from resin to CF and the other was formation of surface functional group and attractive interaction of these functional groups at the interface of fiber and matrix. These two effects showed synergetic contribution to enhance the mechanical properties of CFRTP.

Commercial carbon fiber is sized with Bisphenol A type epoxy, a thermosetting resin, to prevent fiber damage due to friction during weaving and manufacturing processes. When the thermoplastic resin is used as the base material, the interface between the carbon fiber and the thermoplastic resin is very weak because the bonding force with the thermosetting resin is not good, which greatly affects the mechanical properties of the composite material. Therefore, in order to improve the mechanical properties of the thermoplastic composite material, a process of removing the epoxy sizing layer on the surface of the carbon fiber in a furnace is required. In this process, the physical properties of the carbon fiber are changed according to the change of carbon fiber heat treatment conditions. In this paper, the study was carried out to evaluate the tensile strength required for automobile parts by extrusion and injection of thermoplastic resin based carbon fiber composites. Depending on the heat treatment temperature and time of the carbon fiber was a slightly tensile strength of the carbon composite material occurs, the tensile strength of the carbon composite material with a 6 hour heat-treated carbon fiber was measured at 550 ℃ the highest to 93 MPa. When the heat treatment holding time is more than 6 hours or the heat treatment temperature is more than 600 ℃, it may be the damage to the carbon fiber, which can cause a decrease in the tensile strength of the carbon fiber composite material.

최근에 국내에는 다양한 원인에 의한 구조물의 안정성을 우려하는 사회적인 관심이 생겼으며 이에 따른 구조물의 보수·보강에 다양한 연구가 진행되고 있다. 우리나라는 4계절이 뚜렷하며 특히 겨울과 봄에는 일교차가 심하게 발생하는 특징이 있다. 이러한 날씨는 철근콘크리트 구조물에게 동결융해작용을 발생시켜 성능저하의 원인이 되며 구조물의 안정성을 위협할 수 있다. 현재 구조물 보수·보강 방법으로는 탄소섬유나 유리섬유로 FRP(Fiber Reinforced Polymer)를 활용하여 Plate나 Sheet 형태의 부착 보강하는 방법이 일반화 되어있다. 하지만 다소 고가이며 유리섬유는 인체에 유해하다는 연구결과가 있다. 때문에 본 연구에서는 친환경적이고 내열성이 우수한 현무암섬유(Basalt Fiber)를 활용하여 동결융해 작용에 의한 콘크리트의 성능저하를 조건으로 BFRP-콘크리트의 부착성능 및 파괴패턴을 비교 분석하였다. 동결융해시험에 따른 부착강도평가는 동일한 섬유와 수지가 함침된 BFRP를 활용하여 동결융해Cycle(0, 100, 200, 300)과 콘크리트 압축강도(24MPa, 30MPa)를 변수로 부착성능을 평가하였으 며 Case1(선 부착 후 동결융해)과 Case2(선 동결융해 후 부착)로 나누어 진행하였다. Case1과 2 모두 콘크리트 파괴의 형태를 보 였으며 Case2의 경우 Case1에 비하여 부착강도가 감소됨을 나타내었고 동결융해 Cycle이 진행될수록 콘크리트 계면의 성능은 저하되고 부착강도는 평균 약 25%정도 감소하는 것을 확인하였다.