The organic binder-free paste for dye-sensitized solar cell (DSSC) has been investigated using peroxo titanium complex. The crystal structure of TiO2 nanoparticles, morphology of TiO2 film and electrical properties are analyzed by X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Electrochemical Impedance Spectra (EIS), and solar simulator. The synthesized TiO2 nanopowders by the peroxo titanium complex at 150, 300, 400˚C, and 450˚C have anatase phase and average crystal sizes are calculated to be 4.2, 13.7, 16.9, and 20.9 nm, respectively. The DSSC prepared by the peroxo titanium complex binder have higher Voc and lower Jsc values than that of the organic binder. It can be attributed to improvement of sintering properties of TCO/TiO2 and TiO2/TiO2 interface and to formation of agglomerate by the nanoparticles. As a result, we have investigated the organic binder-free paste and 3.178% conversion efficiency of the DSSC at 450˚C.

We report on the successful fabrication of ZnO nanorod (NR)/polystyrene (PS) nanosphere hybrid nanostructure by combining drop coating and hydrothermal methods. Especially, by adopting an atomic layer deposition method for seed layer formation, very uniform ZnO NR structure is grown on the complicated PS surfaces. By using zinc nitrate hexahydrate [Zn(NO3)2 ·6H2O] and hexamine [(CH2)6N4] as sources for Zn and O in hydrothermal process, hexagonal shaped single crystal ZnO NRs are synthesized without dissolution of PS in hydrothermal solution. X-ray diffraction results show that the ZnO NRs are grown along c-axis with single crystalline structure and there is no trace of impurities or unintentionally formed intermetallic compounds. Photoluminescence spectrum measured at room temperature for the ZnO NRs on flat Si and PS show typical two emission bands, which are corresponding to the band-edge and deep level emissions in ZnO crystal. Based on these structural and optical investigations, we confirm that the ZnO NRs can be grown well even on the complicated PS surface morphology to form the chestnut-shaped hybrid nanostructures for the energy generation and storage applications

This research was conducted to evaluate the physicochemical properties of semi-dried jerky made from uncastrated (U) and castrated (C) deer meat. The jerky was manufactured by mixing the ground lean meat with spices followed by drying process, packed and stored aerobically at 25℃ for 20 days. The pH of uncastrated raw meat was significantly (p<0.05) higher than that of castrated meat as well as the pH of the jerky. No effects were found on color, hardness and sensory scores of jerky. Castrated jerky had higher fat content than uncastrated jerky (p<0.05), after 20 days of storage, its TBARS (thiobarbituric acid reactive substances) value was higher than uncastrated jerky (p<0.01). These results suggest that castration contributed to higher fat content and lipid oxidation of semi-dried venison jerky than the uncastrated, without any significant effects on texture and sensory attributes. However, proper packaging should be considered to inhibit lipid oxidation.

복숭아순나방(Grapholita molesta)은 핵과류과실에 일차 피해를 주는 해충이다. 이를 해결하기 위해 종합적병해충관리 [IPM]의 일환으로 써 전세계적으로 교미교란제가 농가에 적용되고 있다. 왁스, 폴리에틸렌 튜브, 에어로졸 형태의 다양한 교미교란제가 상업화되었다. 이 연구에서 는 복숭아순나방 성페로몬 방출기로써 에스테르왁스와 폴리프로필렌(PP)필름백을 구성하는 방출기를 기존의 파라핀 왁스와 폴리에틸렌(PE) 재 질의 필름과 비교하여 페로몬의 방출거동을 분석했다. PE재질의 필름백은 성페로몬의 방출이 불규칙한 반면, PP필름백에서 성페로몬은 시간에 따라 일정하게 방출하는 패턴을 얻었다. 이러한 결과를 토대로 Japan 왁스_PP 필름 방출기(Japan_PP)를 제작하였고, 약 5개월 동안 복숭아과 수원에 적용한 결과 98% 이상의 교미교란 효과가 검증되었다.

Porous W with spherical and directionally aligned pores was fabricated by the combination of sacrificial fugitives and a freeze-drying process. Camphene slurries with powder mixtures of WO3 and spherical PMMA of 20 vol% were frozen at −25 oC and dried for the sublimation of the camphene. The green bodies were heat-treated at 400 oC for 2 h to decompose the PMMA; then, sintering was carried out at 1200 oC in a hydrogen atmosphere for 2 h. TGA and XRD analysis showed that the PMMA decomposed at about 400 oC, and WO3 was reduced to metallic W at 800 oC without any reaction phases. The sintered bodies with WO3-PMMA contents of 15 and 20 vol% showed large pores with aligned direction and small pores in the internal walls of the large pores. The pore formation was discussed in terms of the solidication behavior of liquid camphene with solid particles. Spherical pores, formed by decomposition of PMMA, were observed in the sintered specimens. Also, microstructural observation revealed that struts between the small pores consisted of very fine particles with size of about 300 nm.

γ-Aminobutyric acid (GABA)-containing salt was prepared by crystallization of a mixture of salt water from deep sea and fermentation broth by lactic acid bacteria that contained GABA converted from glutamic acid. Salt from deep sea water has a lower sodium content but higher calcium, potassium and magnesium contents than commercial salt. Instead of monosodium glutamate (MSG), glutamic acid was used for solving the residual MSG problem. Fermentation by a lactic acid bacterium converted 90% of added glutamic acid (5%, w/v) to GABA, and continuous production of colorless fermentation broth containing more than 3% (w/v) GABA was achieved by using an activated carbon. Mixtures of salt water and fermentation broths with various GABA concentrations were co-crystallized and the GABA content was analyzed. This analysis showed that more than 90% of GABA from broth was adsorbed to salt. The appearance and surface of this prepared GABA-containing salt were examined with an image analyzer and scanning electron microscope. No difference was found with commercial sun-dried salt and no separated particles were detected, which indicates that the co-crystallization process used is suitable for the production of GABAcontaining salt.

The alternative advanced lead-acid battery is one of the promising ultrabattery. The lead-carbon battery is also reusable battery consisted of positive electrodes, negative electrode and Electrolyte. Currently, numerous research efforts are performing on activated carbon used as the novel cathode materials. In this study, we have used graphite sheet coated P60 carbon as a cathode material. Graphite electrode is different form used in the normal lead-carbon batteries. It will be expected to increase the conductivity and weigh light. Through charge-discharge experiment and EIS, battery performance analysis were compared with grid form negative electrode. After that, SEM, RAMAN and XRD analyses were studied.

Sulfonated poly(arylene ether sulfone) (SPAES) random copolymers have been perceived as alternatives to perfluorinated sulfonic acid ionomers used as polymer electrolyte membranes for fuel cells. SPAES copolymers are suffering from degradation under harsh fuel cell operation conditions. One solution to overcome the decomposition issue is to fill SPAES copolymers into polymeric support films (e.g., poly(tetrafluoro ethylene), PTFE) with interconnected porous structures. It is difficult to fill the SPAES copolymers dissolved in polar aprotic solvents into PTFE support films owing to their different surface energies. In this study, a SPAES nanodispersion in a water-alcohol mixture is used to make defect-free pore-filling membranes where poly(ethylene glycol) oligomers are added to induce advanced morphologies for fast proton conduction.

본 연구에서는 Montmorillonitrile(MMt)계 무기물을 이용하여 SPAES고분자에 첨가한 후 제조된 용액을 이용하여 복합막을 제조하였으며 특성평가가 진행되었다. 개질되지 않은 MMt의 경우 고분자에 첨가되었을 경우 실리케이트층 구조로 인해 메탄올 투과도는 감소하나 이온전도도가 감소되는 문제점을 가지고 있으므로 본 연구에서는 MMt를 유기화 시켜 최적화된 메탄올 투과도와 이온투과도를 가지는 무기물을 제조하고자 하였으며 최종적으로 제조된 분리막의 특성평가를 진행하였다.

고분자 전해질 막의 성능을 개선하고자 사용된 대표적인 무기물인 solid acid가 첨가된 복합막의 경우 고온에서 높은 열안정성을 나타내며 친수성이 강해지는 장점을 나타내지만 물에 녹는 단점을 가지고 있다. 그러므로 본 연구에서는 phosphotungstic acid(PWA)의 이온전도성을 증가시키며 물에 용해되는 성질을 제거하기 위하여 실리카 입자를 sol-gel법을 이용하여 술폰산기와 아민그룹을 도입시킨 입자를 제조한 후 sulfonated poly(arylene ether sulfone)(SPAES) 고분자에 첨가하여 복합막을 제조하였으며 특성평가가 이루어졌다.

에폭시 수지는 기계적 물성, 내약품성, 치수 안정성 등이 우수하기 때문에 고기능 소재로서 수요가 증가하고 있다. 이에 따라 에폭시 수지 제조공정에서 발생하는 부산물의 양도 증가하여 부산물 내의 원료 물질 회수에 대한 관심이 높아지고 있다. 본 연구에서는 원료물질을 회수하는 증류/분리막 복합 공정에 적용할 수 있는 탈수용 복합막을 연구하였다. 실리카-지르코니아 졸에 α-알루미나를 분산시킨 코팅용액과 실리카 졸을 이용하여 Dip-coating법으로 실리카 복합막을 제조하였다. 에폭시 공정 부산물인 Epichlorohydrin/IPA/H2O을 이용하여 투과증발 실험한 결과 복합막은 총투과도 0.1∼0.7 kg/m²⋅h, 물의 선택도 50∼110를 나타내었다.

A novel cation exchange membrane consisting of polyvinylidene difluoride (PVDF) was prepared for the application of vanadium redox flow battery (VRFB). PVDF used as supporter has considerably high mechanical strength and an intrinsic hydrophobicity. For the successful preparation of the membrane, PVDF powders were modified by potassium hydroxide, which increased the hydrophilicity of PVDF powders. Modified PVDF were grafted with styrene sulfonic acid (SSA) using benzoyl peroxide (BPO) as initiative. The cross-sectional morphology and structure of PVDF/SSA was confirmed by scanning electron microscopy (SEM) and FT-IR. The membrane was characterized by water uptake, dimensional change, ion conductivity and ion exchange capacity (IEC) and cell performance of Vanadium Redox Flow Battery (VRFB) with Nafion 212.