This study introduces the licensing process carried out by the regulatory body for construction and operation of the 2nd phase low level radioactive waste disposal facility in Gyeongju. Also, this study presents the experience and lessons learned from this regulatory review for preparing the license review for the next 3rd phase landfill disposal facility. Korea Radioactive Waste Agency (KORAD) submitted a license application to Nuclear Safety and Security commission (NSSC) on December 24, 2015 to obtain permit for construction and operation of the national engineered shallow land disposal facility at Wolsong, Gyeongju. NSSC and Korea Institute of Nuclear Safety (KINS) started the regulatory review process with an initial docket review of the KORAD application including Safety Analysis Report, Radiological Environmental Report and Safety Administration Rules. After reflecting the results of the docket review, the safety review of revised 10 application documents began on November 29, 2016. Total 856 queries and requests for additional information were elicited by thorough technical review until November 16, 2021. As the Gyeongju and Pohang earthquakes occurred in September 2016 and November 2017, respectively, the seismic design of the disposal facility for vault and underground gallery was enhanced from 0.2 g to 0.3 g and the site safety evaluation including groundwater characteristics was re-investigated due to earthquake-induced fault. Also, post-closure safety assessments related to normal/abnormal/human intrusion scenarios were re-performed for reflecting the results of site and design characteristics. Finally, NSSC decided to grant a license of the 2nd phase low level radioactive waste disposal facility under the Nuclear Safety Laws in July 2022. This study introduces important issues and major improvements in terms of safety during the review process and presents the lessons learned from the experience of regulatory review process.

Waste containers for packaging, transportation and disposal of NPP (Nuclear Power Plant) decommissioning wastes are being developed. In this study, drop tests were conducted to prove the safety of containers for packaging of the wastes and to verify the reliability of the analysis results by comparing the test and analysis results. The drop height of the waste containers was considered to be 30 mm, which is the maximum lifting speed of a 50 tons crane in the waste treatment facility converted to the drop height. Drop orientation of the containers was considered for bottom-end on drop. The impact acceleration and strain data were obtained to verify the reliability of the analysis results. Before and after the drop tests, measurement of the dose rate and the radiographic testing for concrete wall, and measurement of the wall thickness of steel plate were conducted to evaluate the radiation shielding integrity. Also, measurement of bolt torque, and visual inspection were conducted to evaluate the loss or dispersion of radioactive contents. After the drop tests, the radiation dose rate on the container surface did not increase by more than 20%, and there was no crack in the concrete. In addition, the thickness of the steel plate did not change within the measurement error. Therefore, the radiation shielding integrity of the container was maintained. After the drop tests, the lid bolts were not damaged and there was no loss of pretension in the lid bolts. In addition, there was no loss or dispersion of the contents as a result of visual inspection. In order to prove the reliability of the drop analysis results, safety verifications were performed using the drop test results, and the appropriate conservatism for the analysis results and the validity of the analysis model were confirmed. Therefore, the structural integrity of the waste containers was maintained under the drop test conditions.

High Integrity Container (HIC) made of polymer concrete was developed for the efficient treatment and safe disposal of radioactive spent resin and concentrate waste in consideration of the disposal requirements of domestic disposal sites. Permission for application of Polymer Concrete High Integrity Container (PC-HIC) to the domestic nuclear power plants (NPPs) has been completed or is under examination by the regulatory agency. In the case of 860 L PC-HIC for very-low-level-waste (VLLW) or low low-level-waste (LLW), the application of four representative NPPs has been approved, and the license for extended application to the rest NPPs is also almost completed. A licensing review is also underway to apply 510 L PC-HIC for intermediate and low-level-waste (ILLW) to representative nuclear power plants. In order to handle and efficiently store and manage PC-HICs and high-dose PCHIC packages, a gripper device that can be remotely operated and has excellent safety is essential, and the introduction of NPPs is urgent. The conventional gripper device developed by the PC-HIC manufacturer for lifting test to evaluate the structural integrity of PC-HIC requires a rather wide storage interval due to its design features, and does not have a passive safety design to handle heavy materials safely. In addition, work convenience needs to be reinforced for safety management of high radiation work. Therefore, we developed a conceptual design for a gripper device with a new concept to minimize the work space by reflecting on-site opinions on the handling and storage management conditions of radioactive waste in NPPs, and to enhances work safety with the passive safety design by the weight of the package and the function of checking the normal seating of the device and the normal operation of the grip by the detector/indicator, and to greatly improves the work efficiency and convenience with the wireless power supply function by rechargeable battery and the remote control function by camera and wireless monitoring & control system. Through design review by experts in mechanical system, power supply and instrumentation & control fields and further investigations on the usage conditions of PC-HICs, it is planned to facilitate preparations for the application of PC-HIC to domestic NPPs by securing the technical basis for a gripper device that can be used safely and efficiently and seeking ways to introduce it in a timely manner.