This work concentrates on the design and implementation of aptamer-based electrochemical biosensors using a layer-by-layer approach for precise tracking of mucin-1 (MUC1), an important biomarker linked to breast cancer. The electrochemical biosensor was created by modifying a screen-printed carbon electrode (SPCE) with V2C MXene booster and gold nanoparticles (Au-NPs), along with Cd2+ integrated aptamer (AP) (SPCE/V2C-MXene/Au NPs/Cd2+-AP). This biosensor demonstrated high specificity and affinity for MUC1, establishing a sensitive quantification mechanism. The MXene nanolayer was produced and analyzed via TEM, XPS, SEM, AFM, BET, and MAP techniques. It served as a supportive material that enhanced electrochemical conductivity and allowed for the integration of the aptamer (AP) as the biological recognition component. The biosensor was constructed by immobilizing MUC1-specific aptamers onto the surfaces of SPCE/V2C-MXene/Au NPs, enabling selective recognition and binding with MUC1. The recorded signal, corresponding to Cd2+ integrated with AP at SPCE/V2C-MXene/Au NPs/Cd2+-AP, enabled quantitative assessment of MUC1 levels. The findings showed a linear concentration span of 1.0–500 pg/mL for detecting MUC1, achieving a detection limit of 3.45 fg/mL utilizing the SPCE/ V2C-MXene/Au NPs/Cd2+-AP biosensor. The SPCE/V2C-MXene/Au NPs/Cd2+-AP biosensor exhibited a good affinity for the detection of MUC1 in the presence of other breast cancer biomarkers, confirming its selectivity.

To optimize the electrochemical properties of Ni-rich cathode materials, CPAN@SC-NCM811 is prepared via surface modification of single-crystalline LiNi0.8Co0.1Mn0.1O2 cathode material by adding 1, 2 and 3 wt.% of polyacrylonitrile, respectively. Significantly, the results obtained from X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM), and transmission electron microscopy (TEM) verify the successful synthesis of CPAN@SC-NCM811 cathode, which exhibits better electrochemical properties compared to SC-NMC811. After thorough milling and calcination of 2 wt.% polyacrylonitrile with SC-NCM811, the initial discharge specific capacity of prepared S2 sample is 197.7 mAh g− 1 and the capacity retention reached 89.2% after 100 cycles at a rate of 1.0 C. Furthermore, the S2 sample exhibits superior rate performance compared to the other three samples, in which these superior electrochemical properties are largely attributed to the optimal ratio of conductive cyclized polyacrylonitrile coatings. Overall, this work offers guidelines for modifying the surface of SC-NCM811 cathode materials for lithium-ion batteries with exceptional cycling and rate performance.

Biomass-derived carbon materials have attracted considerable attention in electromagnetic wave (EMW) absorption applications due to their advantages of low cost, light weight, and sustainability. Herein, bagasse-based porous carbon (BPC) was prepared by canonization and activation process from natural waste bagasse. The porous flower-like MoS2/ BPC composites were successfully prepared for efficient microwave absorption via hydrothermal process by in-situ formation of flower-like MoS2 into the porous structure of BPC. The effect of hydrothermal time and hydrothermal temperature on surface morphology, degree of graphitization, surface chemical composition and impedance matching of the prepared samples was investigated. Results demonstrated that when the hydrothermal temperature was 220 °C, and the hydrothermal time was 24 h, the obtained MoS2/ BPC sample (named as MoS2/ BPC-220 ℃) showed the minimum reflection loss value (RL) of − 41.6 dB at 8.96 GHz and exhibited effective microwave absorption bandwidth (EAB) of 4.32 GHz at a relatively thin thickness of 1.5 mm. This work provides a promising way to prepare novel biomass-derived porous carbon for strong broadband electromagnetic absorption.

On the wooden slabs unearthed from the tomb of Guojianao (formerly, Guo) in the period of Sun Wu of the Three Kingdoms, there is a sentence with the words “針囊一枚, 白糸一 , 青糸一”. Past scholars interpreted the three characters “ ” ,“ ” and “ ” as the word “縱 (zong)” , which means “silk thread”, and “ ” ,“ ” as the word “㢧 (卷, juan, volume)”, which is a measure word. This study verifies that the word “ ” is “ ”, and “ ”, “ ” are “ ”, which are all variants of the word “線 (xian, line)”. This was achieved by changing the phonetic note. The measure word “ ”, “ ” used for weighing silk thread should be a variant form of the word “斤 (jin)”, which is similar to the writing of “ (jin)” or “ (jin)” in the Pan’s clothing list of the Eastern Jin Dynasty.

Building step-scheme (S-scheme) heterojunctions has recently emerged as a highly effective approach for developing superior photocatalysts for water purification. Herein, a C3N5/ Ag3PO4 (CA) S-scheme heterojunction was prepared by in situ growth of Ag3PO4 nanoparticles on 2D C3N5 nanosheets. Notably, under visible-light irridiation, CA exhibited significantly higher activity in the photodegradation of LEVO, which is about 28.38, 2.41, and 2.14 times higher than the rates for C3N5, Ag3PO4, and the mixture, respectively. Based on the radical scavenging experiments, the mechanism for enhanced photocatalytic performance has been analyzed, is attributed to improved interfacial charge separation, the elevated redox potential of photon-generated electrons and holes, and the increased generation of active species resulting from the S-scheme transfer of photoinduced carriers. Additionally, CA demonstrates greater stability than either C3N5 or Ag3PO4 alone in the photo-oxidation of LEVO and the photodegradation of RhB. In essence, this study not only deepens our comprehension of the photocatalytic mechanism of CA, but also pioneers a novel concept for the development of highly effective and stable S-type heterojunction photocatalysts.

Moso bamboo, as a kind of renewable functional material, exhibits outstanding development potential. It is promising to prepare activated carbon with good mechanical strength and high specific surface area using moso bamboo as raw material. In this work, we employed a hydraulic extruder to extrude the bamboo charcoal and the adhesive to obtain the moso bamboo activated carbon, and improved the specific surface area of the columnar activated carbon through high-temperature water vapor activation. Through the catalytic role of the water vapor activation process, the formation and expansion of the pores were promoted and the internal pores were greatly increased. The obtained columnar activated carbon shows excellent mechanical strength (93%) and high specific surface area (791.54 m2/ g). Polyacrylamide@asphalt is one of the most effective adhesives in the high-temperature water vapor activation. The average pore size (22.99 nm) and pore volume (0.36 cm3/ g) of the prepared columnar activated carbon showed a high mesoporous ratio (83%). Based on the excellent pore structure brought by the activation process, the adsorption capacity of iodine (1135.75 mg/g), methylene blue (230 mg/g) and carbon tetrachloride (64.03 mg/g) were greatly improved. The resultant moso bamboo columnar activated carbon with high specific surface area, excellent mechanical properties, and outstanding adsorption capacity possesses a wide range of industrial applications and environmental protection potential.

In the history of Chinese academics, Xu Shen’s Shuowen Jiezi (hereinafter referred to as Shuowen) is known as “the first of its kind in the world” because it has the dual characteristics of explaining the form, sound, and meaning of Chinese characters and the characteristics of theoretical works on philology, both of which are practical. It has not only become a treasure of codex for the compilation of character books and exegesis, but also laid down the basic patterns of traditional philology and biblio-linguistics, with far-reaching influence. Many scholars have researched Shuowen in the past dynasties, resulting in the formation of an independent thematic discipline called Shuowen, also known as Xuxue (許學). According to Ding Fubao (丁福保), Shuowen jiezi Gulin (hereinafter referred to as Gulin) attached to the Yingyong Zhushu Xingshi Lu (引用諸書姓氏錄) statistics, there were as many as 203 people in the Qing Dynasty who studied and wrote Shuowen. In fact, there are many scholars and their achievements that are not included in the statistics. After Gulin, especially in the last 30 years, a lot of new materials of scholars in the Qing Dynasty who studied the Shuowen have been excavated and published. Most of these new materials are dispersed in their original state in different large series, so they are rarely researched and utilized, and their documentary and scholarly value is in urgent need of formal recognition. Based on the preliminary results of the major project of the National Social Science Foundation (21&ZD299) chaired by Li Yunfu (李運富), this article discusses the excavation, collation, and research of new materials on Shuowen in the Qing Dynasty.

Herein, the present work focuses on the effective counter electrode for dye-sensitized solar cells. The bottom–up approach was adapted to synthesize Mn2O3 nanorods via the hydrothermal method and the reduced graphene oxide was merged with Mn2O3 to prepare a nanocomposite. The prepared nanocomposites were subjected to physio-chemical and morphological characterizations which revealed the crystalline nature of Mn2O3 nanorods. The purity level rGO was characterized using the Raman spectrum and the Fourier transform infrared spectroscopy employed to find the functional groups. The morphological micrographs were visualized using SEM and TEM and the high aspect ratio Mn2O3 nanorods were observed with 5–7 nm and supported by rGO sheets. The electrocatalytic nature and corrosion properties of the counter electrode towards the iodide electrolyte were studied using a symmetrical cell. The as-synthesized nanocomposites were introduced as counter electrodes for DSSC and produced 4.11% of photoconversion efficiency with lower charge transfer resistance. The fabricated DSSC devices were undergone for stability tests for indoor and outdoor atmospheres, the DSSC stability showed 93% and 80% respectively for 150 days.

In this study, a low-cost and easily recyclable porous green adsorbent (magnetic porous loofah biochar, MPLB) was synthesized by modifying the almost zero-cost loofah biochar material with Fe3O4. The successful synthesis of the material was demonstrated by XRD, FTIR, SEM, VSM, and BET. In addition, the material exhibits outstanding magnetic separation performance (40.01 umg/g) allowing for rapid recovery within just 90 s. The adsorption process of phenol on MPLB was found to be spontaneous and endothermic. The experimental data fit exceptionally well with the pseudo-second-order kinetic model and Langmuir model (R2 > 0.99), indicating that the dominant adsorption mechanisms involved monolayer adsorption and chemisorption. These interactions were attributed to host–guest interaction, π–π conjugation, hydrogen bonding, and pore filling. The maximum adsorption capacity calculated using the Langmuir model at 298 K is 39.4 mg/g. Importantly, even after undergoing seven cycles of recycling, MPLB retained 78% of its initial adsorption capacity. In simulated experiments employing MPLB for phenol removal in actual wastewater, an impressive removal rate of 96.4% was achieved. In conclusion, MPLB exhibits significant potential as an effective adsorbent for phenol removal in wastewater.

A glassy carbon electrode modified with a composite consisting of electrodeposited chitosan and carboxylated multi-walled carbon nanotubes (e-CS/MWCNTs/GCE) was used as a working electrode for simultaneous determination of dopamine (DA), serotonin (5-HT) and melatonin (MT), which were related to circadian rhythms. The electrochemical characterizations of the working electrode were carried out via electrochemical impedance spectroscopy and chronocoulometry. It was found that electrochemical modification method, that was cyclic voltammetry, may can cause continuous CS polymerization on MWCNTs surface to form a dense membrane with more active sites on the electrode, and the electrochemically active surface area of e-CS/MWCNTs/GCE obtained was about 7 times that of GCE. The electrochemical behaviour of DA, 5-HT and MT on working electrode were carried out via differential pulse voltammetry and cyclic voltammetry. The results showed that e-CS/MWCNTs/GCE solved the problem that the bare electrode could not detect three substances simultaneously, and can catalyze oxidation potential difference as low as 0.17 V of two substances reaction at the same time, indicating very good electrocatalytic activity. By optimizing the detection conditions, the sensor showed a good linear response to DA, 5-HT and MT in the range of 20-1000 μmol/L, 9-1000 μmol/L and 20-1000 μmol/L, and the detection limits were 12 μmol/L, 10 μmol/L and 22 μmol/L (S/N = 3), respectively. In addition, the proposed sensor was successfully applied to the simultaneous detection of DA, 5-HT and MT in human saliva samples.

An environmentally friendly and low-cost chitosan-containing polysaccharide (CP) composite ZIF-8/CP was designed and prepared based on the difficulty of separating the traditional adsorbent from the water phase. ZIF-8/CP was synthesized through in-situ growth approach. The physical, chemical and structure properties of ZIF-8/CP were determined through a series of characterization methods, including SEM, FT-IR and PXRD. The effects of touch time, pH, temperature, and coexisting ions on adsorption were assessed. In addition, kinetics, isotherms of adsorption and thermodynamics were examined. The data of isotherms for adsorption indicated that the adsorption of ZIF-8/CP on MG was similar to the Langmuir model, with a maximum adsorption capacity of 1428.57 mg/g. Moreover, the kinetic parameters were consistent with the pseudo- 2nd-order equation. Thermodynamic studies (ΔG < 0, ΔH > 0) demonstrated a heat-absorbing and spontaneous adsorption process. Our study reveals that ZIF-8/CP has good adsorption properties and environmental properties.

Decabromodiphenyl ether (BDE209) is a persistent aromatic compound widely associated with environmental pollutants. Given its persistence and possible bioaccumulation, exploring a feasible technique to eradicate BDE209 efficiently is critical for today’s environmentally sustainable societies. Herein, an advanced nanocomposite is elaborately constructed, in which a large number of titanium dioxide ( TiO2) nanoparticles are anchored uniformly on two-dimensional graphene oxide (GO) nanosheets ( TiO2/GO) via a modified Hummer’s method and subsequent solvothermal treatment to achieve efficient photocatalytic degradation BDE209. The obtained TiO2/ GO photocatalyst has excellent photocatalytic due to the intense coupling between conductive GO nanosheets and TiO2 nanoparticles. Under the optimal photocatalytic degradation test conditions, the degradation efficiency of BDE209 is more than 90%. In addition, this study also provides an efficient route for designing highly active catalytic materials.

How to effectively deal with the polluted water by the pollutant of organic dyes is the world problem. It is of great significance if the organic dyes in the polluted water can be directly turned into the useful materials through a facile approach. Herein, the water which contains the common organic dye, Reactive red 2 (RR2), has been chosen to be the model to synthesize graphene quantum dots (GQDs) by a facile route. The comprehensive characterizations, including TEM (HRTEM), XPS, Raman, PL and UV–Vis. spectra, have been performed to confirm the structures and explore the properties of the synthesized GQDs. Meanwhile, the excellent PL properties and low biotoxicity of the GQDs confer them with the potential applications in the biological fields. When the GQDs are excited by the wavelength of 360 nm, the maximum emission is achieved at 428 nm. It is well demonstrated that the synthesized GQDs are able to detect the Al3+ which causes multiple diseases, such as Parkinson, Alzheimer, kidney disease, and even cancer. The detection range is from 90 to 800 μM, which is different from the reported kinds of the literature. Therefore, this work not only provides an economical and environmental route on solving the universal problem from organic dyes, but also facilitates to advancing the synthesis and application of GQDs.

Acrylonitrile–butadiene–styrene (ABS) terpolymer was compounded with short carbon fiber (CF) and carbon nanotube (CNT) using a micro-extruder followed by the injection molding process. Composite samples were fabricated with loading ratios of 20 wt.% CF and 0.1, 0.5 and 1.0 wt.% of CNT. Mechanical, electrical, thermo-mechanical, thermal, melt-flow, and structural investigations of ABS-based composites were conducted by performing tensile, impact, hardness, and wear tests, conductive atomic force microscopy (AFM), dynamic mechanical analysis (DMA), thermal gravimetric analysis (TGA), melt flow rate test (MFR), scanning electron microscopy (SEM) characterization techniques, respectively. According to mechanical test data of resultant composites including tensile and impact test findings, CNT additions led to the remarkable increase in tensile strength and impact resistance for CF reinforced ABS composites. The formation of synergy between CNT nanoparticles and CF was confirmed by electrical conduction results. The conductive path in ABS/CF composite system was achieved by the incorporation of CNT with different loading levels. SEM micrographs of composites proved that CNT nanoparticles exhibited homogeneous dispersion into ABS matrix for lower loadings.

This study investigated the arsenide removal by using mesoporous CoFe2O4/ graphene oxide nanocomposites based on batch experiments optimized by artificial intelligence tools. These nanocomposites were prepared by immobilizing cobalt ferrite on graphene oxide and then characterized using various techniques, including small angle X-ray diffraction, high-resolution transmission electron microscopy and energy-dispersive X-ray spectroscopy. Artificial intelligence tools associated with response surface methodology were employed to optimize the conditions of the arsenide removal process. The results showed that back propagation neural network combined with genetic algorithm was suitable for the arsenide removal from aqueous solutions by the nanocomposites based on the minimum average values of absolute errors and the value of R2. The optimal values of the four variables (operating temperature, initial pH, initial arsenide concentration, and contact time) were found to be 25.66 °C, 7.58, 10.78 mg/L and 46.41 min, and the predicted arsenide removal percentage was 84.78%. The verification experiment showed that the arsenide removal percentage was 86.62%, which was close to the predicted value. Three evaluation methods (gradient boosted regression trees, Garson method and analysis of variance) all demonstrated that the temperature was the most important explanatory variable for the arsenide removal. In addition, the arsenide removal process can be depicted with pseudo-second-order kinetics model and Langmuir isotherm, respectively. The thermodynamics investigation disclosed that the adsorption process was of a spontaneously endothermic nature. In summary, this study showed that ANN-GA was an efficient and feasible method in determining the optimum conditions for arsenic removal by CoFe2O4/ graphene oxide nanocomposites.