This paper intends to present considerations on the question of what is the “load standard” or “design load” for integrity evaluation under normal transportation conditions and what type of design load is good for users. This suggests a direction for subsequent research on producing design loads that transport business companies can utilize without difficulty. Several studies have been conducted to evaluate the integrity of spent nuclear fuel during normal transportation. A representative study recently conducted is the Multi-modal Transportation Test (MMTT) conducted using a commercial spent nuclear fuel cask by US DOE in 2017. In Korea, additional transport tests were planned to acquire sufficient test data under the conditions of road and sea transport considering the Korean situation. As a result, road transport tests were carried out in 2020 and sea transport tests were carried out in 2021. In the road transport test, a driving test that simulates various road conditions and a test that cycled a 4.5 km road eight times were performed. In most cases, the maximum acceleration of less than 1 g occurred, and the maximum strain was less than 48 με. For the sea transport test, the magnitude of both the maximum acceleration and the maximum strain were lower than those in the road transport test. We concluded tentatively that the integrity of spent fuel under normal conditions of transport was satisfactory with a large margin. However, when the storage business is realized and the transport of spent fuel becomes visible, the storage and transport business companies will have to prove the maintenance of the integrity of the spent fuel under normal transport conditions at the request of the regulatory agency. The transport business companies can transport the spent nuclear fuel by using different types of transport casks and different types of trucks and ships from those used in the tests mentioned above. However, it is absurd to have to prove the integrity of spent nuclear fuel by performing expensive tests again. Therefore, in this study, the design load that can be used by transport business companies is to be presented. The design load to be presented should satisfy the following requirements. The design load should be applicable including some differences in the transport cask or transport system, or different design loads should be presented according to the differences. The location where this design load is applied is to be specified (e.g. fuel rod, basket, internal structure). Requirements according to the operating speed of the transport system should be presented together. The type of design load is to be presented (e.g. PSD, SRS, FDS etc.). Other types of standards may be presented. For example, a speed limit for a vehicle carrying spent nuclear fuel may be suggested, or a speed limit for a vehicle passing through a speed bump may be suggested. In order to present such a reliable design load, a multi-axis vibration excitation shaker table test will be carried out. Though this shaker table test, the behavior of the nuclear fuel assembly is closely evaluated by applying the data obtained from the road and sea transport tests previously performed as an input load. In addition, FDS (Fatigue Damage Spectrum) will be produced and applied to experimentally evaluate the durability of fuel assemblies under normal transport conditions.

사용후핵연료를 저장하는 볼트체결 저장용기의 격납경계를 형성하는 주된 구성요소는 금속 밀봉재이다. 이러한 금속 밀봉 재는 열과 방사선에 의해 그 성질이 저하된다. 또한, 금속 밀봉재가 강한 열에 장기간 노출되면 크리프 현상이 발생한다. 이러한 크리프는 밀봉시스템에 응력 이완을 가져와서, 결국 밀봉재의 건전성을 해치게 된다. 이러한 응력 이완은 금속 밀봉재의 밀봉성능 저하로 이어지며, 저하의 정도에 따라 저장용기의 누설을 야기할 수 있다. 또한, 볼트 체결력의 감소도 밀봉성능 저하에 영향을 미친다. 본 논문에서는 금속 밀봉재의 격납건전성과 볼트체결력 감소를 평가하기 위해 수행한 가속화 시 험의 결과에 대하여 기술한다. 전 시험기간 동안 각 시편에서의 누설률, 볼트 변형률, 금속 밀봉재 주변 온도를 계측하여 분석하였고, 금속 밀봉재는 저장기간 50년 동안 격납건전성을 유지함을 입증하였다. 또한, 가속화 시험의 타당성에 대해서 기술하였다.

With the confirmation of the Free Trade Agreement (FTA) and as cheap foreign agricultural products are beginning to be freely distributed in Korea, the government has taken a greater interest in securing the competitiveness of domestic agriculture. Accordingly, the Korean government has presented plans to advance the interests of ‘small but strong farmers’ and secure their competitiveness in line with the agricultural conditions in Korea. The government also announced that it will focus on leading these efforts in rural areas. The main thrust of this plan to support ‘small but strong farmers’ focuses onutilizing advanced peripheral technologies such as IT and BT; however, there are only a few Information Management Division centers currentlyoperating across the nation, and these are mainly in the IT-related divisions of the Agricultural Research and Extension Services and Agricultural Technology Centers. Therefore, in this study, we used the responses from a survey of farmers to identify regional differences in informatization levels and the digital divide among ‘small but strong farmers’ according to the presence or absence of an Information Management Division center. As a result, we found that the ‘small but strong farmers’ in regions with an active Information Management Division center received more IT services and had a higher level of informatization. Thus, to increase the use of IT-related peripheral technology by these ‘small but strong farmers’, it is important to maintain or increase the number of Information Management Division centers.

The effects of compaction pressure and sintering temperature on the densification of Fe-40wt%Ni alloy nanoparticles were analyzed. The Fe-Ni nanoparticles were fabricated by an arc-discharge method and then, compacted at three different pressures and sintered at 550 to . Densification was completed at temperature as low as and high-pressure compaction was found to enhance densification. Densification behaviors and microstructure developments have been investigated through density measurements, electron microscopies, and hardness measurements.