Electrochemical reduction has previously been reported for uranium oxide and mixed oxide nuclear fuel (uranium oxide, plutonium oxide). The laboratory scale electrochemical reduction of plutonium oxide powder is demonstrated in CaCl2- 1wt%CaO. The plutonium oxide contained within a permeable steel basket cathode is sacrificed during the process. A graphite anode is also employed during the reduction, leading to a significant contamination of the product.

The present work reports a systematic study of using carboxymethylated cellulose (CMC) as water-bornebinder to produce Li4Ti5O12-based anodes for manufacture of high rate performance lithium ion batteries. When theLTO-to-CB-to-CMC mass ratio is carefully optimized to be 8:1:0.57, the special capacity of the resulting electrodes is144 mAh·g−1 at 10 C and their capacity retention was 97.7% after 1000 cycles at 1C and 98.5% after 500 cycles at5C, respectively. This rate performance is comparable or even better than that of the electrolytes produced using con-ventional, organic, polyvinylidene fluoride binder.

An enantioselective recognition of D- and L-tryptophan (Trp)-b-cyclodextrin (CD) inclusion complex was performed using electrochemical and FT-Raman spectroscopic analysis. From the electrochemical analysis, the selectivity coefficient (KDL) of b-CD inclusion complexes was found higher than that of the D- and L-Trp in phosphate buffered saline (PBS, pH=7.0) solution. The percentage of enantioselectivity (I%ee) for peak current of D-Trp-b-CD inclusion complexes was observed higher than that of L-Trp-b-CD inclusion complexes in PBS solution. From Raman spectroscopy, chemical shift difference (D, cm-1) for the C=C stretch, ring vibration, and ring breathing of D-Try-b-CD inclusion complex were observed higher than that of L-Trp-b-CD inclusion complex. The electrochemical and Raman spectroscopic analyses were found very useful for chiral detection of racemic amino acid in the presence of b-CD.

In this study, several kinds of active carbons with high specific surface area and micro pore structure were prepared from the coconut shell charcoal using chemical activation method. The physical property of prepared active carbon was investigated by experimental variables such as activating chemical agents to char coal ratio, flow rate of inert gas and temperature. It was shown that chemical activation with KOH and NaOH was successfully able to make active carbons with high surface area of 1900~2500 m2/g and mean pore size of 1.85~2.32 nm. The coin cell using water-based binder in the electrolyte of LiPF6 dissolved in mixed organic solvents (EC:DMC:EMC=1:1:1 vol%) showed better capacity than that of oil-based binder. Also, it was found that the coin cell of water-based binder shows an improved cycling performance and coulombic efficiency.

음이온 교환막의 치환체 특성을 파악하기 위하여 탄화수소의 분자구조가 다른 세 종류의 음이온 교환기를 vinyl benzyl chloride (VBC) base 막에 도입하였다. 지방족계로 trimethylamine (TMA), 고리형계로 N-methylpiperidine (MP), 방향족계로 pyridine (Py)은 아민화 반응을 통하여 도입되었다. 각각의 반응속도는 막저항(MER)과 이온교환능력(IEC) 변화의 관측으로부터 Py < MP < TMA의 순서로 반응하고 있음을 보여주었다. 한편 SEM image에서는 Py 치환체 막이 가장 균일하고 치밀한 구조를 보여주었으며, 전기화학적 특성에서도 Py이 상용막(AMX)과 비슷한 막저항(5.0 Ω·cm2 >, in 0.5 mol/L NaCl)을 나타내었다. 이 모든 결과로부터 치환체의 공명구조는 균질한 이온교환막의 제조에 기여하고 있음을 알 수 있었다.

The microstructures and cyclic voltammograms of Al-Si/C nano-composites were investigated as the anode of lithium ion batteries. Al-Si nanoparticles were prepared by the arc-discharge method. Al-Si/C nanoparticles were obtained by coated Al-Si nanoparticles with the precursor of glucose (C6H12O6) as carbon source. It was indicated that the post carbon coating treatment can reduce Al2O3 film on Al-Si particles, and new phase Al4C3 formed in the process can activate the inactivated materials of electrode in a certain extent.

본 연구에서는 스테인리스강을 사용하여 전형적인 3-전극 시스템의 순환전류전압법으로 트리에탄올아민(TEA) 용액 중에서 전류-전압 곡선을 측정하였다. 스테인리스강은 작업 전극으로, Ag/AgCl 전극은 기준 전극으로, 그리고 백금 선은 상대 전극으로 각각 사용하였고, 그 결과, 트리에탄올아민 용액에서의 스테인리스강의 C-V 특성은 순환전류전압법으로부터 산화전류에 기인한 비가역 공정으로 나타났다. 부식억제제의 확산계수의 효과는 농도 증가에 따라 감소하였다. 그리고 부식억제 효과는 농도 0.5 N의 NaClO4, 2.5x10-3 M TEA용액에서 가장 컸으며, 1.5 N NaClO4, 1.0x10-3 M TEA용액에서 가장 낮았다.

The Chlor-alkali (CA) process is a representative electrolysis system to produce valued chemicals such as chlorine gas and sodium hydroxide. Membrane cell process has been obtaining the largest market shares, because it is free from environmental issues and low chemicals purity. For the CA process, commercially available membrane materials are perfluorinated sulfonic acid ionomers (PFSAs) with high chemical resistance. Unfortunately, there are limited data associated with the relationships between membrane material parameters and CA performances. It prevents the CA membrane development to be difficult. In this study, the influences of PFSA membrane thickness are disclosed, considering their ion transport behaviors, gas evolution capability, and chemical/electrochemical resistances under CA operation conditions.

Activated carbons (ACs) were prepared by activation of coal tar pitch (CTP) in the range of 700°C-1000°C for 1-4 h using potassium hydroxide (KOH) powder as the activation agent. The optimal activation conditions were determined to be a CTP/KOH ratio of 1:4, activation temperature of 900°C, and activation time of 3 h. The obtained ACs showed increased pore size distribution in the range of 1 to 2 nm and the highest specific capacitance of 122 F/g in a two-electrode system with an organic electrolyte, as measured by a charge-discharge method in the voltage range of 0-2.7 V. In order to improve the performance of the electric double-layer capacitor electrode, various mixtures of CTP and petroleum pitch (PP) were activated at the optimal activation conditions previously determined for CTP. Although the specific capacitance of AC electrodes prepared from CTP only and the mixtures of CTP and PP was not significantly different at a current density of 1 A/g, the AC electrodes from CTP and PP mixtures showed outstanding specific capacitance at higher current rates. In particular, CTP-PP61 (6:1 mixture) had the highest specific capacitance of 132 F/g, and the specific capacitance remained above 90% at a high current density of 3 A/g. It was found that the high specific capacitance could be attributed to the increased micro-pore volume of ACs with pore sizes from 1 to 2 nm, and the high power density could be attributed to the increased meso-pore volume.

An in-vivo diagnosis of trace Mg(II) ion was performed using a low-cost and environment-friendly voltammetric method, using a graphite counter and reference electrodes and a fluorine-immobilized graphite working electrode, and clean deep seawater was used as an electrolyte solution. Under optimum conditions, the analytical working ranges attained microgram ranges, and a detection limit of 80.6ugL-1 was obtained using stripping voltammety with 60 sec accumulation time. Ex-vivo application was performed on fish liver and mice droppings. The developed techniques can be applicable to tumor cell analysis.

폴리스티렌계 음이온교환막은 제조가 쉽고 공정이 간단한 장점을 갖고 있으나 막의 취성이 높아 내구성이 떨어지 는 단점을 가지고 있다. 이를 보완하여 유연하고 우수한 내구성을 갖는 막을 만들기 위해 acrylonitrile-butadiene rubber를 첨 가제로 사용하여 음이온교환막을 제조하였다. 다양한 조성의 vinylbenzylchloride와 styrene, divinylbenzene, acrylonitrile- butadiene rubber 그리고 benzoyl peroxide로 이루어진 단량체 용액을 지지체인 직물 형태의 지지체인 poly(propylene)위 에 캐스팅 후 열중합 가교시킨 다음 trimethylamine과 acetone을 이용하여 음이온 교환기(-N+(CH3)3)를 함유하는 복합막을 제 조하였다. 음이온 교환막 제조시 첨가제의 함량에 따른 막의 성능을 평가하여 최적화 비율을 찾고, 단량체의 함량을 변화하여 함수율, 이온교환용량(IEC) 및 전기저항 값을 측정하였다. 그 결과 최적화 비율로 제조된 막들은 아스톰사의 상용화 음이온 교환막(AMX)보다 높은 IEC와 낮은 전기저항 값을 나타내는 동시에 유연성과 내구성이 우수한 막이 만들어진 것을 확인할 수 있었다.

A series of high capacity soft carbons with different phosphorus contents were successfully prepared by carbonizing petroleum cokes treated with hypophosphorous acid at 900˚C. The effect of phosphorus content on the electrochemical performance of the soft carbons was extensively investigated. The P-doped soft carbons exhibited greatly enhanced discharge capacities and outstanding rate capabilities with increasing phosphorus content. In addition, the influence of temperature on the electrochemical behaviors of the soft carbons was investigated in a wide temperature range of 25˚C to 50˚C. Surprisingly, the electrochemical properties of the pristine and P-doped soft carbons were highly sensitive to the operating temperature, unlike conventional graphite. The pristine and P-doped soft carbons exhibited significantly high discharge capacities of 470 and 522 mAh/g, respectively, at a high temperature of 50˚C.

The pickling brine generated from the salting process of kimchi production is difficult to treat biologically due to very high content of salt. When pickling brine is treated and discharged, it cannot satisfy the criteria for effluent water quality in clean areas, while resources such as the salt to be recycled and the industrial water are wasted. However, sterilization by ozone, UV and photocatalyst is expensive installation costs and operating costs when considering the small kimchi manufacturers. Therefore there is a need to develop economical process. The study was conducted on the sterilization efficiency of the pickling brine using electrochemical processing. The electrochemical treatment of organic matters has advantages over conventional methods such as active carbon absorption process, chemical oxidation, and biological treatment because the response speed is faster and it does not require expensive, harmful oxidizing agents. This study were performed to examine the possibility of electrochemical treatment for the efficient processing of pickling brine and evaluated the performance of residual chlorine for the microbial sterilization.

포화지방산과 인지질(DMPC)혼합 LB막에 대한 전기화학적 특성을 조사하였다. 포화지방산과 DMPC 혼합 단분자 LB막은 ITO glass에 Langmuir-Blodgett법을 사용하여 제막하였다. 전기화학적 특 성은 NaClO4 용액에서 3 전극 시스템 (Ag/AgCl 기준전극, 백금선 카운터 전극 및 LB 필름이 코팅된 ITO 작업 전극)으로 순환전압전류법을 사용하여 측정하였다. 그 결과 포화지방산과 인지질(DMPC)의 LB막은 순환전압전류도표로부터 산화전류로 인한 비가역공정으로 나타났다. 포화지방산과 인지질 (DMPC)혼합(몰비 1:1) LB막(C14, C16, C18, C20)에서 확산계수(D)는 0.05 N NaClO4에서 각각 1.2x10-3, 2.1x10-3, 1.4x10-4 및 1.1x10-3 cm2/s로 산출되었다.

The electrochemical properties of cells assembled with the LiNiO2 (LNO) recycled from cathode materialsof waste lithium secondary batteries (Li[Ni,Co,Mn]O2), were evaluated in this study. The leaching, neutralization andsolvent extraction process were applied to produce high-purity NiSO4 solution from waste lithium secondary batteries.High-purity NiO powder was then fabricated by the heat-treatment and mixing of the NiSO4 solution and H2C2O4.Finally, LiNiO2 as a cathode material for lithium ion secondary batteries was synthesized by heat treatment and mixingof the NiO and Li2CO3 powders. We assembled the cells using the LiNiO2 powders and evaluated the electrochemicalproperties. Subsequently, we evaluated the recycling possibility of the cathode materials for waste lithium secondary bat-tery using the processes applied in this work.

Commercial activated-carbon used as the electrode material of an electric double-layer capacitor (EDLC) was posttreated with various acids and alkalis to increase its capacitance. The carbon samples prepared were then heat-treated in order to control the amount of acidic functional groups formed by the acid treatments. Coin-type EDLC cells with two symmetric carbon electrodes were assembled using the prepared carbon materials and an organic electrolyte. The electrochemical performance of the EDLC was measured by galvanostatic charge-discharge, cyclic voltammetry, and electrochemical impedance spectroscopy. Among the various activated carbons, the carbon electrodes (CSsb800) prepared by the treatments of coconutshell-based carbon activated with NaOH and H3BO5, and then heat treated at 800˚C under a flow of nitrogen gas, showed relatively good electrochemical performance. Although the specific-surface-area of the carbon-electrode material (1,096m2/g) was less than that of pristine activated-carbon (1,122m2/g), the meso-pore volume increased after the combined chemical and heat treatments. The specific capacitance of the EDLC increased from 59.6 to 74.8 F/g (26%) after those post treatments. The equivalent series resistance of EDLC using CSsb800 as electrode was much lower than that of EDLC using pristine activated carbon. Therefore, CSsb800 exhibited superior electrochemical performance at high scan rates due to its low internal resistance.

This study was carried out to investigate the response characteristics of a hydrogen sulfide electrochemical gassensor for several wastewater odors. At first, it was found that bubbling sampling method was superior toheadspace sampling method in terms of sensor sensitivity. High correlation between odor concentration and sensorresults was shown for two wastewater which were r=0.977 for food-waste recycling wastewater and r=0.997for food industry wastewater. On the other hand, no correlation (r=0.258) was found for plating wastewater,because hydrogen sulfide was not the main odorant for that.

Carbazole과 diketopyrrolopyrrole를 기본 골격으로 한 2,5-bis-(2-butyl-octyl)-3,6-bis-[5-(4-carbazol-9-ylphenyl)-thiophen-2-yl] -2,5-dihydro-pyrrolo[3,4-c]pyrrole-1,4-dione (PCTDPP12)을 스즈키 커플링 반응을 이용하여 합성하였다. UV-Visible 분광법으로 확인 한 결과 PCTDPP의 용액과 필름의 최대 흡수 피크는 각각 643 nm와 671 nm이며, PCTDPP12의 광학적 밴드갭은 각각 1.84 eV이다. 열처리에 의해 PCTDPP12의 UV-visible 흡광도 및 최대 흡수 파장이 변화된는 것을 관찰 하였다. 그리고 순환 전압 전류법에 의해 조사한 PCTDPP12의 HOMO 및 LUMO 에너지 준위는 –5.34 eV와 -3.54 eV 이다.