The air dilution olfactory method to measure complex odors needs to store and carry odor samples from the field sampling until the analysis in laboratories. Until the analysis of sample in the laboratory, odor dilution factor (odor sensitivity) in the sample bag may decrease over time depending on the characteristics of each odor substances. This is one of the limitation for the air dilution olfactory method. Thus, the air dilution device enable to measure without loss in complex odors of samples. Recently, many studies on the performance test of on-site air dilution devices, i.e., field olfactometer, has been conducted to figure out the feasibility of the field olfactometers. In this study, seven odor samples were collected from five odor emission source sites. And comparative analysis with the air dilution olfactory method was carried out to assess the field applicability of the olfactometer. As results, the performance of the field olfactometer used in this study is regared as the affordable method. The dilution factors from between two methods showed the similar values, indicating low values of standard deviations. In order to ensure the accuracy and precision of measurement data using the field olfactometer, methodology minimized variables (that may affect measurement) needs to establish.

As the capacity of renewable power generation facilities rapidly increases, the variability of electric power system and gas turbine power generation is also increasing. Therefore, problems may occur that require urgent repair while the gas turbine rotor is stopped. When the gas turbine rotor turning is stopped and then restarted, if the turning period is not appropriate, severe vibration may occur due to rotor bending. As a result of the experiment, it was confirmed that normal operation is possible when the gap data measured at the start of rotor turning after maintenance work is similar to the existing value. And the vibration value at the start of rotor turning was lower as the rotor temperature was lower or the stop period was shorter.

본 논문에서는 철근콘크리트 골조를 주 대상으로 하여 설계 및 시공 전 과정에 대한 디지털전환 전략과 기술개발에 대하여 기술하 였다. 건설 현장의 BIM 도입과 디지털 전환이 기대만큼 활성화되지 않는 중요원인을, 모델링 솔루션을 이용한 설계모델 구축의 생산 성과 후속 프로세스에서 요구하는 필요충분한 정보를 제공하는 완성도에서 찾을 수 있다. 특히 방대한 양의 상세설계 모델 구축에 소 요되는 과도한 노력과 단순반복 작업 과정에서 발생할 수 있는 인적 오류에 의한 정확성 결여는 건축 프로젝트의 디지털 전환 실현을 위하여 해결되어야 할 기술적 장벽이다. 이러한 배경에서 본 연구에서는 철근콘크리트 골조 공사를 대상으로 디지털전환과 현장적용 을 목표로 이를 실현하기 위한 개념적 전략 수립과 기술개발 사례에 대하여 기술하였다. 이를 위하여 시공 단계에서 필요한 상세설계 정보를 포함하는 건물골조 상세설계 BIM 모델링 기술개발 결과를 제시하고, 특히 배근상세설계 등 반복성이 높은 상세설계 업무를 자동화하여 기본설계 2D CAD 도면에서 출발하여 3D BIM 모델을 구축하고 상세설계 BIM 모델을 생성한 후 이를 활용하기 위한 플 랫폼 구축까지의 프로세스를 완성하였다. 제시된 자동화기술과 현장관리 플랫폼에 의한 프로세스는 CAD 도면 기반의 전통적 건설 프로세스를 대체하기 위해 요구되는 업무 생산성과 기술적 정보 완성도를 확보한 것으로 평가되었다.

PURPOSES : This study investigated the field applicability of pervious concrete to pavement base courses. Pervious concrete was developed at laboratory level, and the compaction methods, field moisture content, and fundamental properties when the material was constructed in the field were studied. METHODS : Field-applied pervious concrete was compacted at different levels using a tandem roller, and cores were taken to investigate the compressive strength, infiltration rate, continued porosity, and freeze-thaw resistance. In addition, the optimum field construction and quality control of the moisture content of a batch plant were measured. RESULTS : The moisture content of pervious concrete has an essential effect on workability and quality control during field test construction. From the test herein, the optimum value at a batch plant was found to be approximately 2.5±0.1%. The compaction level is also a crucial parameter at construction sites because it affects the mechanical and penetration properties. Considering both compressive strength and drainage, the recommended compaction was three times the round trip when a tandem roller was used. The penetration coefficient was 0.88 cm/sec when applying three times the round trip of the tandem roller. The freezing and thawing weight loss rates of the applied pervious concrete satisfied the required condition of 14% or less, regardless the compaction level. CONCLUSIONS : With the suggested mixed proportions of pervious concrete, the recommended compaction was three times the round trip of a tandem roller and a moisture content of approximately 2.5±0.1% from a batch plant. When these conditions were satisfied, the mechanical and drainage properties satisfied the required criteria.