This study is an experimental study to evaluate the vehicle-protection performance of the reinforced F section of a concrete median barrier. To reinforce the strength performance and durability of the F section, the design strength of concrete was increased and a wire mesh was added. The reinforced F section was tested in an actual collision to verify the protection performance of the SB4 class(Impact Severity: 160kJ) concrete barrier. In the truck-crash test for strengthperformance evaluation, no damage or no sufficient scattering occurred to cause damage to a third party. In addition, the truck smoothly moved through an escape box after the collision. THIV and PHD, which are criteria for evaluating the occupant-protection performance, were measured at 75% and 64% of the limit, respectively, and were confirmed to provide good occupant-protection performance. The vehicle rotations after the collision were 12%–19% of the allowed limits.

In this study, we compare and analyze stress and vertical deflectional displacement according to cross sectional shape changes of the beam using finite element analysis. The 11,000mm long horizontal beam showed stress differences depending on the cross-sectional variation, with stress differences of up to 200MPa and at least 149MPa. The deflection at the end of the beam also differed by up to 586 mm and at least 208mm. The weight change applied according to the cross-sectional shape of the steel horizontal beam was up to 235kgf, at least 144kgf, and showed the best stress and deflection characteristics in the cross sectional shape with a weight of 185kgf. This allowed us to improve structural safety through sectional shape optimization despite the weight increase.

현무암 섬유를 함유한 BFRP 시트와 복합섬유 패널로 보강한 정사각형 단면 철근콘크리트 기둥에 대한 반복하중 실험을 수행하여 지진 거동을 검토하였다. 30%가량의 상당한 수준의 축하중비 조건 하에서 전단 손상이 발생하였음에도 불구하고, 보강 실험체에서 변위연성도 및 에너지 소산능력의 증가를 확인하였다. 실험체의 파괴 모드는 휨-전단 고연성 파괴로 분류 되며, 철근콘크리트 구조물에서 자주 관찰되는 파괴 모드이다. 하지만 이러한 파괴에 이르는 정사각형 단면 철근콘크리트 기둥에 BFRP을 포함한 복합재료 보강이 미치는 영향에 대한 연구가 현재까지 광범위하게 이루어지지는 않았다. 복합재료로 보강한 철근콘크리트 기둥의 휨-전단 거동을 보다 깊이 이해하는데 본 연구의 결과가 기여할 것으로 기대한다.

This study covered the Mulmae, architectural drawing recorded on Yeonggeon-uigwes and Sanleung-uigwes during the late Joseon Dynasty. In uigwes, the term ‘Mulmae’ was used as a mixture until the 17th century, but from the 18th century, the term ‘Mulmae(勿乙每, 勿每, 水每)’ was unified into ‘Mulmae(水每)’. The paper of the Mulmae was made to be used during the construction period by using a thick oil paper called Yudun. Four Yudun were connected, and its size was 197.4×141cm, which was rather large. The Yingzaofashi(營造法式) of Song Dynasty describes how to draw a longitudinal section on a scale of 1/10. The scale of 1/10 was the maximum when comparing the size of the Mulmae with the buildings in uigwes. A sectional drawing of Gongpo in Geunjeongjeon was drawn on a scale of 1/10. There is a testimony that a senior carpenter drew a cross-section on a scale of 1/10. Therefore, it was determined that the scale of the longitudinal section drawn on the Mulmae paper was 1/10. The term 'the Mulmae' was used equally by carpenter active in Japanese colonial era. The scope of the painting was clarified from pillar to rafter. Uigwes records that the Mulmae was made for wood processing. Through this, it can be understood that the Mulmae painted the entire structure as a longitudinal section.

FRP 보강이 RC 기둥의 내진성능에 미치는 효과를 평가하고자 다양한 실험 연구가 수행되어 왔다. 그 중 많은 연구가 휨지배를 받는 원형 단면 RC 기둥의 거동에 초점을 맞추었다. 단면 형태가 FRP 보강에 의한 구속효과에 영향을 주기 때문에, 단면 형태에 따라 보강효과 및 최종손상 양상이 다를 수 있다. 또한, 기존 RC 기둥 중 일부는 현재의 구조기준을 만족하지 못하는 설계로 인하여 취성적인 파괴 모드인 전단 파괴가 발생할 것으로 여겨진다. 이 두 가지 조건을 고려하여, 현무암 섬유를 함유한 FRP 시트와 복합섬유 패널로 보강한 정사각형 단면을 가진 짧은 RC 기둥의 전단 거동을 살펴보기 위하여 반복하중 실험을 수행하였다. 실험 결과에서 전체적인 전단 거동의 개선을 확인하였으며, 이러한 경향은 모서리 부분에서 심각한 손상이 발생할 때까지 유효하였다.

A basic metal deposition experiment for manufacturing aluminum parts was performed using WAAM (Wire arc additive manufacturing), and the cross-sectional shape of the laminate according to nine deposition conditions. The effect of heat input was analyzed for the bead shape according to the deposition conditions, and the deposition efficiency was calculated by analyzing the cross-sectional shape of thin-wall parts made of aluminum. The amount of heat input was used in the experiment from about 2.7 kJ/cm to 4.5 kJ/cm, and the closer the heat input was to 4.5kJ/cm, the higher the deposition efficiency was. The maximum lamination efficiency obtained through this study reached 76%.

The numerical analysis of two-dimensional transient flow around the obstacle with rotated square cross sections was carried out. The obtained velocity distributions for each time step and each rotation angle were imaged to provide data for CNN(convolutional neural network). Both classification and regression neural networks were used for prediction of rotation angle. As results The classification method incorrectly predicted the rotation angle in only 2 of the 470 images. The regression method predicted the rotation angle errors within except 2 out of 470 images. From these facts, it could be concluded that both methods can be sufficiently applicable to the flow analysis.

The purpose of this study is to investigate the interrelationship of how the ship's wave resistance performance changes with the change of the longitudinal position of the section line in the ship's lines, and to find a way to use it in the hull-form design. To this end, we developed a hull-form automatic change algorithm that can maintain the proper hull-form while moving the section lines in the longitudinal direction, and the computer program for a numerical analysis was developed to apply the developed algorithm. By applying the developed hull-form automatic change algorithm and the wave resistance performance prediction program, the numerical analysis package was constructed. The numerical analysis was carried out for the passenger ship. Numerical analyzes were carried out by moving the section lines of the passenger ship in the longitudinal direction, and the results were compared with each other. Based on the numerical results, we attempted to investigate the correlation between the section line movement and the wave resistance performance.

본 논문에서는 AISC 표준 단면을 설계 변수로 하는 캔틸레버 타입 헬리데크 모델의 유전 알고리즘 최적설계를 소개한다. AISC 표준 단면을 단면 형상별로 분류하고 단면적 순으로 정렬한 후 정수 단면 번호를 부여하여 설계 변수로 최적설계를 수행하였다. 이 과정을 통하여 이산화된 설계 변수를 가지는 최적설계 문제를 해결하기 위해 유전 알고리즘을 적용하였다. 또한, 제약조건으로 허용응력 및 허용응력비 검사 조건을 모두 고려하여 구조물의 구조 안정성을 고려한 설계를 수행하였다. 최적설계 과정중 매 반복계산 마다 수행되는 구조해석 시간을 단축시키기 위해 선형 중첩법을 사용하였고, 이를 통해 구조 해석 시간을 약 75% 감소시킬 수 있었다. 또한 헬리데크 최적설계의 경량 효과를 높이기 위해 부재 그룹 세분화를 하였고, 그 결과를 선행 연구 모델, 기존의 부재 그룹 모델과 비교하였다. 그 결과 선행연구 대비 약 30톤의 부재를 절감할 수 있었으며, 구조적으로도 보다 안전한 헬리데크 설계를 얻을 수 있었다.

본 연구에서는 열유도상분리법(thermally induced phase separation)을 사용하여 제조한 플라워 형태의 단면을 갖는 PVDF [poly(vinylidene fluoride)] 중공사 분리막에 대한 친수화 코팅과 그에 따른 특성평가에 대한 연구를 수행하였다. 연구에 사용한 중공사 분리막은 (주)퓨어엔비텍에서 제조한 PVDF 소재의 분리막이었으며, 친수화 코팅 실험은 PEBAX 1657, 2533, 3533의 공중합체 고분자를 사용하여 농도가 다른 용액을 제조 후 딥 코팅 방법을 이용하여 실시하였다. 친수화 코팅이 된 중공사 분리막은 친수화 정도를 파악하기 위하여 SEM 촬영 및 접촉각 측정을 실시하였다. SEM 촬영 결과 코팅의 농도가 증가하고 코팅횟수가 증가할수록 코팅층의 두께가 두꺼워짐을 확인하였고, 접촉각 측정의 경우 코팅의 농도가 증가하고 코팅횟수가 증가할수록 접촉각이 낮아짐을 확인하였다. 기체 투과 실험 결과 코팅농도가 증가하고 코팅횟수가 증가할수록 산소 기체투과량이 감소하였으며 친수성이 높은 PEBAX 1657로 코팅한 중공사의 기체투과량이 PEBAX 2533과 3533으로 코팅된 중공사보다 낮은 기체투과량을 가짐을 확인하였다.

The purpose of this paper is to evaluate the structural performance of joints between modules with steel plate press forming type non-symmetric cross section. The main experimental variables are direction of load, whether vertical bolts are fastened, and whether the concrete inside the column is filled. A total of three experiments were performed for each variable. Experimental results show that the behavior of the joints dominated by the local buckling deformation of the upper and lower beam flanges of the module joints, and the final failure was the fracture of the column-beam welds. In case of short side direction, it is possible to secure the performance of intermediate moment frame (0.02 rad). In case of long side direction, it is evaluated that the performance of special moment frame (0.04 rad) is secured regardless of whether or not concrete is infilled in the column.