PURPOSES : To investigate the fundamental characteristics of blast-furnace slag mortar that was hardened with activating chemicals to capture and sequester carbon dioxide. METHODS : Various mix proportions were considered to find an appropriate stregnth development in regards with various dosages of activating chemicals, calcium hydroxides and sodium silicates, and curing conditions, air-dried, wet and underwater conditions. Flow characteristics was investigated and setting time of the mortar was measured. At different ages of 3, 7 and 28days, strength development was investigated for all the mix variables. At each age, samples were analyzed with XRD. RESULTS : The measured flow values showed the mortar lost its flowability as the activating chemicals amount increased in the scale of mole concentration. The setting time of the mortar was relatively shorter than OPC mortar but the initial curing condition was important, such as temperature. The amount of activating chemicals was found not to be critical in the sense of setting time. The strength increased with the increased amount of chemicals. The XRD analysis results showed that portlandite peaks reduced and clacite increased as the age increased. This may mean the Ca(OH)2 keeps absorbing CO2 in the air during curing period. CONCLUSIONS : The carbon capturing and sequestering activated blast-furnace slag mortar showed successful strength gain to be used for road system materials and its carbon absorbing property was verified though XRD analysis.

본 연구에서는 폐금속 광산 주변 비소와 중금속으로 오염된 논토양을 효과적으로 복원하기 위한 안정화 제로써 석회석과 제강슬래그의 처리효과와 그 적용성을 검토하기 위해 담수답의 환원 환경을 적용한 컬럼 실험을 실시하였다. 실험결과 담수된 논토양의 환원 환경에서는 철과 망간 성분이 환원되어 급격하게 용출되는 시점에 중금속 성분도 급격하게 용출되는 경향이 나타났으며, 대조구(무처리)의 경우 침출수에서 오염기준을 초과한 시료가 나타났다. 그러나 석회석 5%와 제강슬래그 5%로 각각 처리한 토양은 모두 오염기준 이하로 대조구보다 중금속 농도가 매우 낮게 검출되었다. 석회석과 제강슬래그 모두 담수답의 환원 환경에서 좋은 처리효과를 나타내어 효과적인 안정화제로 판단되었으며, 특히 제강슬래그는 담수답 환 경에서 지속적으로 증가하는 비소 성분에 대해서 좋은 처리효과를 나타내었다.

Phosphorus exhibits considerable segregation in steelmaking slag. In order to recover phosphorus from slag to K3PO4 via molten iron, a carbothermic reaction using microwave heating was suggested recently. The carbothermic reduction of phosphorus from slag to molten iron using microwave heating was carried out at 2073K. However, at this temperature the thermodynamic properties of both slag and molten iron cannot be determined experimentally. Therefore, the computational approach of the so-called CALPHAD method is very useful to understand the transfer of phosphorus from slag to metal and to enhance this reaction. In the present investigation, a theoretical study of the reduction behavior of phosphorus in slag was carried out at much lower temperatures using the recently developed thermodynamic database in the FactSage program. The calculated results showed reasonable accordance with the experimental data; namely, the thermodynamic database could be applied successfully to higher temperature reactions. The current study found that higher temperature and high SiO2 concentration are favorable for the recovery of phosphorus from slag.

Furnace slag powder used currently in Korea needs to add special functions in response to the increase of large-scale projects. In addition, it is advantageous in that it has a lower hydration heat emission rate than ordinary Portland cement and improves properies such as the inhibition of alkali aggregate reaction, watertightness, salt proofness, seawater resistance and chemical reslstance. However, furnace slag powder is not self-hardening, and requires activators such as alkali for hydration. Accordingly, if recycled fine aggregate, from which calcíum hydroxide is generated, and furnace slag, which requires alkali stimulation, are used together they play mutually complementary roles, so we expect to use the mixture as a resource-recycling construction material. Thus the present study purposed to examine the properties and characteristics of furnace slag powder and recycled aggregate, to manufacture recycled fine aggregate mortar using furnace slag and analyze its performance based on the results of an experiment, to provide materials on mortar using furnace slag as a cement additive and recycled fine aggregate as a substitute of aggregate, and ultimately to provide basic materials on the manufacturing of resource-recycled construction materials using binder and fine aggregate as recycled resources.

본 연구는 포장재로서 투수콘크리트의 실질적인 현장적용을 위한 자료제시와 성능향상 방안을 도출하기 위하여 슬래그골재와 플라이애시의 혼입률에 따른 포장용 투수콘크리트의 역학적 특성을 평가하였다. 시험결과, 포장용 투수콘크리트의 공극률 및 투수계수는 슬래그골재의 혼합비율이 증가함에 따라 증가하고 플라이애시 혼입률 증가에 의하여 감소하는 경향을 나타내었으며 국내 포장용 투수콘크리트에 관한 규정(8% 및 0.01cm/sec)을 만족하였다. 압축강도 및 휨강도는 슬래그골재의 혼입률이 증가함에 따라 감소하였으나, 플라이애시의 혼입률이 증가함에 따라 크게 증가하는 경향을 나타내어 플라이애시를 5% 이상 혼입하면 슬래그골재를 50% 사용한 경우에도 국내 포장콘크리트에 관한 규정(18MPa 및 4.5MPa 이상)을 만족하였다. 또한 강섬유를 0.75vol.% 혼입한 경우 사용하지 않은 경우에 비하여 휨강도가 22.8% 증가 하였다. 미끄럼저항성은 슬래그골재의 혼입률이 증가에 따라 BPN값은 증가하였고, 플라이애시의 혼입률 증가에 의해 BPN값은 감소하는 경향을 나타내었으며, 내마모성 및 동결융해저항성은 부순골재만을 사용한 경우에 비해 슬래그골재의 혼합비율이 증가함에 따라 감소하였고, 플라이애시를 10% 혼입한 경우에는 현저히 개선되어 혼입하지 않은 경우에 비하여 내마모성 및 내동해성이 각각 약 5.6% 및 14.3% 정도 개선되는 것으로 확인되었다.

Furnace slag powder used currently in Korea needs to add special functions in response to the increase of large-scale projects. In addition, it is advantageous in that it has a lower hydration heat emission rate than ordinary Portland cement and improves properties such as the inhibition of alkali aggregate reaction, watertightness, salt proofness, seawater resistance and chemical resistance. However, furnace slag powder is not self-hardening, and requires activators such as alkali for hydration. Accordingly, if recycled fine aggregate, from which calcium hydroxide is generated, and furnace slag, which requires alkali stimulation, are used together they play mutually complementary roles, so we expect to use the mixture as a resource-recycling construction material. Thus the present study purposed to examine the properties and characteristics of furnace slag powder and recycled aggregate, to manufacture recycled fine aggregate mortar using furnace slag and analyze its performance based on the results of an experiment, to provide materials on mortar using furnace slag as a cement additive and recycled fine aggregate as a substitute of aggregate, and ultimately to provide basic materials on the manufacturing of resource-recycled construction materials using binder and fine aggregate as recycled resources.

The feasibility study of using converter slag as a solidifying agent of digested sewage sludge cake has been performed. The availability of converter slag as solidifying agent has been investigated by several trial tests. Based on the trial test results, the optimum mixing ratios of sludge cake and solidification additive are estabilished. Finally the solidification characters of sludge cake are elucidated by SEM and EDS. It is ascertained that converter slag with a small amount of quicklime enhences the solidification. From the result of pH test, overall pH of specimens tends to decrease slowly with curing time. After solidifying specimens had been cured for 7 days, these are water-cured for 24 hours. The weight and strength of all the specimens are nearly the same regardless of the mixed ratios of solidifying agent. The result of leaching tests for four heavy metal ions, Cd, $Cr^{6+}$, Pb and Cu show that the leaching strength becomes below the decision criteria of the specific wastes, respectively. The SEM observation of the delicate structure shows that needlelike crystals appear after solidification which are not observed before. From the EDS analysis, it is found that the main ingredients of needlelike crystals are Ca, Si, Al and O.

본 연구는 원자력 시설 해체 시 발생되는 저준위 및 극저준위 폐토양, 점토와 산업부산물인 고로슬 래그를 이용하여 방사성 폐기물을 안전하게 담지할 수 있는 비소성 시멘트의 제조 가능성을 평가하고 광물· 형태학적 분석을 통하여 생성된 반응 물질에 대하여 고찰하였다. 본 연구에서는 (1) 폐토양, 점토 및 고로슬 래그의 특성 분석, (2) 폐토양, 점토 및 고로슬래그를 고화재 및 성분조정제로 이용한 원전 해체 폐기물 담지를 위 한 비소성 시멘트 제조 및 최적의 배합 비율 도출, (3) 제조된 비소성 시멘트 고화체의 수화반응 생성물질에 대하여 광물·형태학적 분석 등을 수행하였다. 비소성 시멘트 고화체의 광물·형태학적 분석 결과, 폐토양과 점 토는 수화반응 생성물이 관측되지 않았으며, 고로슬래그의 경우 고화체의 강도를 발현시킬 수 있는 수화반응 생성물질인 calcium silicate hydrate (CSH), 에트링가이트(ettringite)가 생성되는 것을 확인하였다. 폐토양, 점 토를 고화재로 이용한 비소성 시멘트의 재령 28일 후 고화체는 최적의 배합 비율에서 약 3 MPa의 강도를 나 타내 처분장 인수기준 압축강도인 3.44MPa를 만족하지 못하는 것을 확인하였다. 그러나, 고로슬래그를 고화 재로 이용한 비소성 시멘트는 모든 실험 조건에서 처분장 인수기준 압축강도를 만족하며, 최적의 배합 비율 에서는 약 27 MPa로 높게 나타나는 것을 확인할 수 있었다. 이러한 결과를 통하여 비소성 시멘트 고화재로 고로 슬래그, 방사성 핵종에 대한 흡착제 역할로 폐토양 및 점토를 이용한다면 방사성 폐기물 처분을 위한 최적의 비소성 시멘트를 제조할 수 있을 것으로 판단된다.