Fe(C) nanocapsules were prepared by the chemical vapor condensation(CVC) process using the pyrolysis of iron Their characterizations were studied by means of X-ray diffraction, X-ray photoelectron spectrometer and transmission electron microscopy. The long-chained Fe(C) nanocapsules hav-ing the mean size of under 70 nm could be obtained below in different gas flow rates. The particle size of the powders was increased with increasing decomposition temperature, but it was decreased with increasing CO gas flow rate. The Fe powders produced at consisted of three layers of phases, but it had two phase core-shell structure which consited of phase of core and graphite of shell at

FePt nanoparticles for high-density magnetic recording media were synthesized by the simultaneous chemical reduction of Fe(acac) and Pt(acac) with 1,2-hexadecanediol as the reducing reagent. TEM images showed that the shape of as-synthesized FePt nanoparticle was spherical and average particle size was 3 nm. Also, SAD pattern showed that crystal structure was disordered FCC (face centered cubic). These FCC structured nanoparticles were transformed FCT (face centered tetragonal) structure by annealing at 55 for 30 min in Ar atmosphere. XRD analysis revealed that as-synthesized FePt nanoparticles were transformed from disordered FCC to ordered FCT. Finally, the coercivity of 2 kOe for FePt nanoparticles with FCT structure was obtained by VSM measurement.

Zirconium nitride powders were synthesized at a relatively lower temperature using methane as a reducing agent in the nitridation of zircoia. ZrO2 powder was prepared by a sol-gel technique. The resulting sol-gel was centrifuged, and the gel was washed with deionized water. Anhydrous ammonia was used as the nitrogen source and methane was used as the reducing agent. Conversion diagrams show the equilibrium solid phase as a function of reagent concentrations for a specific temperature and gas pressure for the reagent system NH3-ZrO2-CH4. The reagent concentration ranges within which pure ZrN is formed increase with increasing reaction temperature. Low pressure with an excess of hydrogen decreases the reaction temperature at which pure ZrN is formed. Low pressure together with the introduction of excess hydrogen into the reaction system increases Zr and N conversion efficiency and retards C deposition.

Nanostructured Cu-AlO composite powders were synthesized by thermochemical process. The synthesis procedures are 1) preparation of precursor powder by spray drying of solution made from water-soluble copper and aluminum nitrates, 2) air heat treatments to evaporate volatile components in the precursor powder and synthesis of nano-structured CuO + O, and 3) CuO reduction by hydrogen into pure Cu. The suggested procedures stimulated the formation of the gamma-AlO, and different alumina formation behaviors appeared with various heat treating temperatures. The mean particle size of the final Cu/AlO composite powders produced was 20 nm, and the electrical conductivity and hardness in the hot-extruded bulk were competitive with Cu/AlO composite by the conventional internal oxidation process

Ultrafine TiC-15%Co powders were synthesized by a thermochemical process, including spray drying, calcination, and carbothermal reaction. Ti-Co oxide powders were prepared by spray drying of aqueous solution of titanium chloride and slurry, both containing cobalt nitrate, fellowed by calcination. The oxide powders were mixed with carbon powder to reduce and carburize at 1100~125 under argon or hydrogen atmosphere. Ultrafine TiC particles were formed by carbothermal reaction at 1200~125, which is significantly lower than the formation temperature (~1) of TiC particles prepared by conventional method. The oxygen content of TiC-15%Co powder synthesized under hydrogen atmosphere was lower than that synthesized under argon, suggesting that hydrogen accelerates the reduction rate of Ti-Co oxides. The size of TiC-15%Co powder was evaluated by FE-SEM and TEM and Identified to be smaller than 300 nm.

나노미터 크기의 결정립을 가지는 나노분말 및 나노복합분말의 제조와 특성에 관한 연구가 매우 활발하다. 나노복합분말의 제조방법에는 기상증발후 응축법, 화학응축법, 기계적합금법 등이 있으나, 고순도 및 균일한 크기분포의 분말과 응집되지 않은 분말의 제조 조건을 가장 잘 만족하는 방법은 화학기상응축법(Chemical Vapor Condensation; CVC)이다. 본 연구그룹 에서는 CVC밤법으로 이용하여 공구/금형재료에 가장 많이 사용되는 WC/Co 합금

열화학 기상 증착법을 이용하여 암모니아 처리에 따른 촉매 금속의 표면형태와 탄소 나노튜브의 성장을 조사하였다. 암모니아 처리의 열화학 과정의 조절에 의해 고르게 분산된 수직 성장된 탄소 나노튜브를 얻었다. 탄소 나노튜브 합성시 암모니아처리는 수직성장 및 고밀도 성장에 중요한 과정으로 그 역할에 대해 알아보았다. 고밀도의 수직 배향된 탄소나노튜브의 구조와 형태는 주사전자 현미경과 투과전자 현미경, 라만을 이용하여 관찰하였다.

Alkyl polyglucosides were synthesized by solvent-free glycosidation using ultrasonic emulsification. We examined glycosidation conditions of fatty alcohol with glucose hydrate and anhydrous glucose in the presence of p-toluenesulfonic acid. Glucose was emulsified in a molar excess of fatty alcohol for 20 minutes with a ultra-sonicator at room temperature and converted in a stirred reactor to more than 95% polyglucoside within 2.5~3.5 hr under 20~30 mmHg at 110℃ with a three-fold molar ratio of fatty alcohol to glucose in the presence of 1mol% p-toluenesulfonic acid. It was possible to obtain a polyglucoside mixture of HLB 13 consisting of 65% monoglucoside and 35% oligoglucoside with less than 1% of fatty alcohol.