검색결과

검색조건
좁혀보기
검색필터
결과 내 재검색

간행물

    분야

      발행연도

      -

        검색결과 191

        41.
        2017.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Stress and fatigue are general physical aspects of our daily lives. It has been shown that physical therapists have different levels of job stress and fatigue according to the type A/B behavior patterns. This study collected data from 212 physical therapists between October 28 and November 23, 2016 using an anonymous, self-administered questionnaire. The study results showed the proportion of physical therapists with the Type A behavior patterns(TABP) was 18% greater than that of physical therapists with the Type B behavior patterns(TBBP). In this study, physical therapists with TABP were compared with physical therapists with TBBP. The results indicated that physical therapists with TABP were more inclined to experience higher levels of overall job stress and fatigue from the following stress factors: physical environment, job requirement, and job autonomy. Therefore, the stronger the tendency toward TABP, the stronger the feeling of job stress and fatigue from physical environment, job requirement, and job autonomy. Those with a tendency toward TBBP showed positive correlations between job requirement and the total job stress score; thus, the stronger the tendency toward TBBP, the stronger the feeling of overall job stress and fatigue from job requirement. This study suggests that it is necessary to manage the job stress and fatigue of physical therapists with both TABP and TBBP and to manage the job stress and fatigue of physical therapists with the type A behavioral pattern.
        4,000원
        42.
        2017.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        High voltage electric power transmitter GIS(Gas Insulated Switchgear) above 72.5kV needs to satisfy domestic Korean peninsular standard(ES-6110-0002) in KEPCO with respect to normal and special operation conditions which include internal gas pressure, dead weight, wind and seismic load. Some other requirements not described in Korean standard can be applied from other international standards such as IEC(International Electronical Committee) 62271-203 and 62271-207. The GIS is a kind of pressure vessel structure made of aluminum and filled with SF6 gas of internal pressure 0.4~0.5MPa. Finite element analysis of GIS is performed with such operational loads including seismic loading and the stability and reliability is determined according to ASME BPVC(Boiler and Pressure Vessel Code) SEC. VIII standard where the allowable stress level of the pressure vessel is suggested. The result shows that the stress of GIS is satisfied the allowable stress level and the safety factor is about 2.3 for Korean peninsular standard.
        4,000원
        43.
        2017.04 구독 인증기관 무료, 개인회원 유료
        As the size of the wind power becomes larger, the development of the assembly type wind power which is advantageous in transportation and installation is active. This advantage comes from the economic point of view, and the stiffener is applied to the inner side, so that the safety is high. Large wind power require door openings for maintenance. The door opening has an irregular cross-section, and an excessive stress active due to the door opening. In this paper, the stresses occurring around the door opening was analyzed. As a result, small stress values were appeared in the tower, as the number of stiffeners were increased. Also, stress values were decreased a little in the tower as the opening shape become to ellipse was closer.
        3,000원
        44.
        2016.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        본 연구는 다목적 관리기의 동력전달 시스템이 가혹한 작동환경에서 겪는 응력상황에 대한 분석을 유한요소해석을 수행함으로써, 기계요소의 안전성을 평가하는 한편, 개선 방안을 도출하고자 진행되었다. 엔진으로부터 작업기에 이르는 과정에 존재하는 동력전달 시스템은 엔진의 출력이 과도하게 인가될 경우 매우 높은 수준의 응력을 나타낼 우려가 있으며 따라서 이와 같은 가혹한 조건을 고려하기 위하여 동력전달 시스템의 출력축이 정지된 상황을 가정하여 시뮬레이션을 수행하였다. 볼클러치(Ball-clutch)와 PTO 조인트(Power take-off joint)에 대하여 응력해석을 수행한 결과 허용접촉응력 이상의 높은응력이 국부적으로 발생한다는 사실을 확인하였고, 이러한 문제를 해결하기 위하여 접촉부의 형상을 변경하여 추가적인 시뮬레이션을 수행하였다. 접촉부의 모서리에 일정 반경의 모깎기를 적용하거나 기계요소의 형상을 변화시켜 접촉면의 위치를 바꿈으로서 과도한 응력집중을 방지할 수 있음을 확인할 수 있었다. 이를 바탕으로 보다 우수한 내구성 및 신뢰성을 지닌 다목적 관리기를 개발할 수 있을 것으로 판단된다.
        4,000원
        46.
        2016.11 KCI 등재 구독 인증기관 무료, 개인회원 유료
        On Tuesday, January 17, 1995, an earthquake of magnitude 7.2 struck the Port of Kobe. In effect, the port was practically destroyed. After a hazard investigation, researchers reached a consensus to adopt a performance-based design in port and harbor structures in Japan. A residual displacement of geotechnical structures after an earthquake is one of the most important engineering demands in performance-based earthquake-resistant design. Thus, it is essential to provide reliable responses of geotechnical structures after an earthquake through various techniques. Today, a nonlinear explicit response history analysis(NERHA) of geotechnical structures is the most efficient way to achieve this goal. However, verification of the effective stress analysis, including post liquefaction behavior, is difficult to perform at a laboratory scale. This study aims to rigorously verify the NERHA by using well-defined field measurements, existing numerical tools, and constitutive models. The man-made, Port Island, in Kobe provides intensive hazard investigation data, strong motion records of 1995 Kobe earthquake, and sufficient engineering parameters of the soil. Two dimensional numerical analysis was conducted on the caisson quay wall section at Port Island subjected to the 1995 Kobe earthquake. The analysis result matches very well with the hazard investigation data. The NERHA procedure presented in this paper can be used in further studies to explain and examine the effects of other factors on the seismic behavior of gravity quay walls in liquefiable soil areas.
        4,300원
        47.
        2016.10 KCI 등재 구독 인증기관 무료, 개인회원 유료
        본 논문에서는 풍력 블레이드와 같이 세장비가 크고 초기 비틀림이 존재하는 복합재료로 구성된 블레이드에 대한 이차원 단면의 차원축소와 복원관계를 이론적으로 기술하였다. 그리고 VABS 이용한 보의 차원축소모델에 대한 유효성을 검증하기 위해 선행연구 모델을 활용하여 기존 연구결과를 수치적으로 비교하였다. 실물과 가장 가까운 날개 구조물 2차원 형상에 단 면해석을 적용하여 정밀한 단면의 이산화를 수행하고 VABS를 이용하여 블레이드의 특성(질량행렬, 강성행렬)을 포함한 1 차원 보 모델링을 수행하였다. 1차원 보 모델을 통해 세장비가 큰 날개 구조물의 거동을 확인하고 내부하중을 계산하여 단 면위치에서 변형률 복원을 수치적으로 계산하고 이산화된 단면에 수치적으로 매핑하여 시각적으로 확인하고 여유마진을 계 산하였다.
        4,000원
        49.
        2016.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        스트레스 수준에 따라 산림치유 프로그램의 선호도에 차이가 있는지를 살펴 보았다. 편의표본추출(convenience sampling)방법을 이용하여 성인 남·여를 대상으로 산림치유 프로그램 선호도와 사회․심리적 스트레스 척도에 관한 설문을 실시하였다. 사회․심리적 스트레스 척도(PWI-SF: Psycho·social Well-being Index Short Form)를 근거로 성인 620명을 건강군, 잠재적 스트레스군, 고위험군으로 분류하였다. 자료분석은 SPSS 21.0 프로그램을 사용하였다. 스트레 스 수준에 따른 세 군 사이의 산림치유 프로그램 선호도 차이를 알아보기 위해 일원 분산분석(one-way ANOVA)을 이용하였다. 스트레스 수준에 따라 산림치유 프로그램 선호도(호흡법·호흡체조, 자유롭게 숲속걷기, 물 흐르는 소리 듣기, 카운슬링·상담 등 전문가 코칭, 스트레스 관련 강의, 대인관계 커뮤니케이션 강의, 경관보기, 숲 해설 듣기, 삼림욕·풍욕·일광욕)에 있어서 차이가 있었다. 고위험 스트레스군은 카운슬링·상담 등 전문가 코칭, 스트레스 관련 강의, 대인관계 커뮤니케이션 강의 등의 인지적인 접근의 프로그램을, 건강군은 호흡법·호흡체조, 자유롭게 숲속걷기 (신발착용), 물 흐르는 소리 듣기, 경관보기, 삼림욕·풍욕·일광욕 등의 오감을 활용하는 감성적인 접근의 프로그램을 각각 상대적으로 높게 선호하는 것으로 나타났다. 잠재적 스트레스군에 있어서는 두드러진 선호도가 발견되지 않았다. 본 연구 결과가 스트레스 정도에 따른 산림치유 프로그램을 개발을 위한 기초자료로 활용되기를 기대한다.
        4,000원
        50.
        2016.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        본 논문에서는 기존에 개발된 생브낭의 원리를 이용한 응력개선방법에 부가적인 면외 워핑함수를 도입하여 후처리함으로써 기계 및 열응력을 개선할 수 있는 방법을 소개하였다. 열응력 예측이 중요한 문제로 다루어지고 있으며, 이에 따라 수많은 보이론들이 개발되어왔다. 일반적으로 고차이론들이 열응력 예측에 유용하다고 알려져 있지만, 자유도가 많아 계산과정이 복잡하다는 단점이 존재한다. 이러한 단점들을 보완하기 위해, 본 연구에서는 계산이 비교적 간단한 고전 보이론의 변위장에 면외 워핑함수를 부가적으로 도입하고 합응력 등가를 통해 후처리함으로써 보 구조물의 열응력을 정확하게 예측할 수 있는 방법을 제시하였다. 그리고 다양한 경계조건을 가지는 수치예제들을 통해 탄성해와 비교함으로써 그 정확도를 검증하고, 면외 워핑함수가 응력개선에 미치는 영향에 대해 분석하였다.
        4,000원
        51.
        2016.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this study, analysis on the stiffness of the headrest, the stiffness of front-rear load and the torsion of cushion frame was performed using finite element method in order to investigate the properties of the stress-deformation by material characteristics according to the test requirements of FMVSS (Federal Motor Vehicle Safety Standard). The results are shown that AZ31 (Mg alloy) and A365 (Al alloy) with low modulus of elasticity and density have higher strain rate than steel in terms of stress-deformation and meet the standards for safety within 108 mm of the maximum amount of deformation. Considering it’s safety and durability, however, the selection of AZ31 for light weight seems difficult to gain the reliability because it causes an excessive deformation, and therefore it is not expected to be used for recliner where stress is concentrated and also the bracket linking rail and cushion frame.
        4,000원
        52.
        2016.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The residual stress analysis and fatigue test of a steel plate with a hole were performed in order to investigate the effects of the cold expansion on the fatigue life of the plate. The cold expansion method is a metal forming process by expanding a hole in order to induce compressive tangential residual stresses near the hole. In this research, a S45C steel plate of 3.2 mm thickness with a hole of 4.318 mm diameter was cold expanded by using a mandrel, resulting in a degree of expansion 1.47%. A significant amount of compressive tangential residual stress of 502 MPa at the hole surface was calculated using the finite element analysis and the compressive residual stress was more widely spreaded in the entry and exit planes than the mid plane in the plate thickness. The compressive tangential residual stresses showed a very beneficial influence on the fatigue life of the plate by increasing 1.2 to 2 times longer lives compared to the plate without cold expansion, depending on the applied load levels. Fatigue crack initiated and propagated at the hole surface of the mandrel entrance region, where relatively lower magnitude of compressive residual stress was found than the other region.
        4,000원
        53.
        2016.03 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Recently, Live-Virtual-Constructive (L-V-C) integrate training system has proposed as a solution for the problems such as limitation of training areas, increase of mission complexity, rise in oil prices. In order to integrate each training system into the one effectively, we should solve the issue about stress of pilots by the environmental differences between Live and Virtual simulation which could be occurred when each system is connected together. Although it was already examined in previous study that the psychological effects on pilots was occurred by the environmental differences between actual and simulated flights, the study did not include what the causal factors affecting psychological effects are. The aim of this study is to examine which environmental factors that cause pilots’ psychological effects. This study analyzed the biochemical stress hormone, cortisol to measure the pilots’ psychological effects and cortisol was measured using Enzyme-linked immunoassay (EIA). A total of 40 pilots participated in the experiment to compare the differences in pilots’ cortisol response among live simulation, virtual simulation, and the virtual simulation applying three environmental factors (gravity force, noise, and equipment) respectively. As a result, there were significant differences in cortisol level when applied the gravity force and equipment factors to the virtual simulation, while there was no significant difference in the case of the noise factor. The results from this study can be used as a basis for the future research on how to make L-V system by providing minimum linkage errors and design the virtual simulator that can reduce the differences in the pilots’ psychological effects.
        4,000원
        54.
        2016.03 KCI 등재 구독 인증기관 무료, 개인회원 유료
        본 연구는 사무직 종사자들의 직무스트레스 완화를 위 하여 원예식물 및 활동에 관한 사전 선호도와 직무스트 레스의 연관성을 분석하고자 실시하였다. 원예 활동 경 험과 관련된 사전 선호도 조사에서 원예식물 중 많이 키 워본 식물 및 선호하는 원예식물은 화훼, 채소, 과수 순 으로 조사되었으며 경험해 본 원예활동은 감상하기가 가장 높게 나타났다. 선호하는 원예활동은 키우기, 이용하 기, 감상하기 순으로 조사되었다. 또한, 원예활동 경험에 따른 직무스트레스 측정 결과 식물 가꾸기를 선호하는 사 람의 직무 스트레스가 낮게 나타나는 것으로 조사되었으 며, 채소류에 비해 화훼류를 선호하는 사람이 직무자율 성 결여에 대한 스트레스에서 유의한 차이로 높게 나타 났다. 직무불안정 및 관계갈등 대한 직무스트레스는 식 물이 비교적 유용하다고 응답한 집단의 점수가 낮았다. 이러한 연구결과를 통해 원예활동 프로그램이 직장 내 대 인관계 향상 및 직무스트레스 관리에 적용 가능한 활동 으로 개발할 필요성이 있는 것으로 판단되었다.
        4,000원
        55.
        2015.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        상태 기반 페리다이나믹 모델은 일반적인 재료 구성 모델을 구현할 수 있고 비국부 영역 내에서 연결된 모든 결합의 변형을 통해 각 절점의 재료 응답이 결정되기 때문에 체적 및 전단 변형을 모두 표현할 수 있다. 따라서 상태 기반 모델은 복잡한 동적 취성 파괴 현상(분기균열, 2차 균열, 계단균열, 균열 유착 등)을 해석하는데 유용하다. 본 논문에서는 평면응력 탄성체에 대해 2차원 상태 기반 페리다이나믹 모델을 적용하고 에너지해방율과 페리다이나믹 에너지 포텐셜로부터 손상 모델을 구성하였다. 페리다이나믹 파괴 해석 모델을 통해 취성 유리 재료에 대해 균열 면에 평행한 압축 응력파가 균열 분기 패턴에 미치는 영향에 대해 조사하였다. 실험을 통해 관찰된 동적 균열 진전 및 분기 패턴에 대한 주요 특성들이 페리다이나믹 해석을 통해 확인되었다. 또한 강한 인장 하중 하의 계단균열과 이차균열 등이 상태 기반 페리다이나믹 시뮬레이션을 통해 잘 모사가 되는 것을 확인할 수 있었다.
        4,000원
        56.
        2015.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The finite element stress analysis of large sized rectangular water tank structures made of stainless steel materials is carried out for various combined load cases. The combined load cases for a large size of 5,000ton are further determined using the specification(KS B 6283) established from the Korean Standards Association. The changed water capacity due to the size of reservoirs could be heavily dependent for evaluating seismic effects, especially for large reservoirs. For the better numerical efficiency, the rectangular panels are modelled using the ANSYS ADPL module. The numerical results obtained for different load cases mainly show the effect of the interactions between the different load combination and other various parameters, for example, the water capacity, and different stainless steel materials. The structural performance for various load combinations is also evaluated.
        4,000원
        57.
        2015.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        This paper develops a LED fishing lamp mounting system which slides in and out a LED fishing lamp mounting rack according to fishing situation of a fishing boat. Sliding mechanism of the LED fishing lamp mounting system is realized with a rack and pinion. Components of the LED fishing lamp mounting system are modeled with finite elements. In addition, the LED fishing lamp mounting system is modeled with rigid bodies. A rigid body model of the LED fishing lamp mounting system is interfaced with finite element component models to develop a computational model of the LED fishing lamp mounting system. A simulation is performed with the developed computational model for dynamic stress analysis of the LED fishing lamp mounting system. A bouncing, rolling, and pitching motion which describe a very rough sea are used as input conditions for the simulation. Six cases are considered for the simulation based on the number of fishing lamp and the location of sliding rack.
        4,000원
        58.
        2015.04 구독 인증기관 무료, 개인회원 유료
        This study numerically investigates buckling behavior of press braked steel plates with a free edge. In order to improve structural stability during construction, the top flanges of press-braked U section girder are laterally braced by the installation of prefabricated half-deck. Thus, an unbraced length is taken as the longitudinal spacing of pockets on the half-deck, which are to make composite section. This study performed 3D finite element analyses to evaluate an equivalent effective width of cold-formed flange with a free edge. Through the parametric numerical analyses, the elastic buckling stresses of the cold-formed flanges with rounded corner in the cross-section were compared with those of general flat plates. Then, the equivalent effective width of the cold-formed (press-braked) flanges were numerically examined for some representative cases.
        3,000원
        59.
        2015.04 구독 인증기관 무료, 개인회원 유료
        제품 개발기간의 단축속도가 빨라지는 현 시점과 제품의 부품 시험을 통한 개발 과 정은 현실적인 한계에 부딪히고 있다. 이러한 문제점을 해결하기 위해 지금 까지는 가 속수명시험(Accelerated Life Test)법을 개발·적용해 왔다. 그러나 제품의 사용조건이 가혹해 짐으로써 온도를 이용한 가속시험을 적용하기에는 한계가 있다. HALT는 급격한 온도변화와 6축 진동을 시료에 전달할 수 있는 장비로써 위의 조 건을 충족시킬 수 있다.[5] 그러므로 본 연구에서는 부품과 재료의 신뢰도 정보를 신속 하게 얻을 수 있는 HALT의 국내외 연구 동향과 적용 현황을 비교 분석 뿐만 아니라 HALT와 HASS의 효과적인 활용방안을 모색하고자 한다.[2]
        4,500원
        60.
        2015.03 구독 인증기관 무료, 개인회원 유료
        Orthodontic is important to apply the optimal orthodontic force. The orthodontic bracket is deformed and the stress caused by tension and torsion of the wire. In this study, using the ANSYS the material that is currently widely used in orthodontic bracket material of stainless steel, ceramic, titanium, polycarbonate, by applying the nitinol analyzed the strain and the stress distribution on the bracket side. Simulation results on the stress distribution and deformation, and it was found a difference of each material.
        3,000원
        1 2 3 4 5