간행물
한국전산구조공학회 논문집 KCI 등재 Journal of the Computational Structural Engineering Institute of Korea
- 발행기관 한국전산구조공학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1229-3059 (Print)2287-2302 (Online)
- 수록기간 1988 ~ 2024
- 주제분류 공학 > 토목공학 공학 분류의 다른 간행물
- 십진분류KDC 531DDC 624
권호리스트/논문검색
제30권 3호 (2017년 6월) 10건
1.
2017.06
구독 인증기관 무료, 개인회원 유료
To study the behavior of structures subject to blast loads it is important to calculate the loads due to the explosives accurately, especially in the case of interior explosions. It is known that numerical method based on computational fluid dynamics can estimate relatively accurate blast load due to the interior explosion including reflection effect. However, the numerical method has disadvantages that it is difficult to model the analysis and it takes much time to analyze it. Therefore, in this study, the analytical method which can include the reflection effect of the interior explosion was studied. The target structures were set as the slabs of residential buildings subject to interior explosion that could lead to massive casualties and progressive collapses. First, the numerical method is used to investigate the interior explosion effect and the maximum deflection of the slab which was assumed to be elastic, and compared with the analytical method proposed in this study. In the proposed analytical method, we determine the weighting factor of the reflection effect using the beam theory so that the explosion load calculation method becomes more accurate.
4,000원
2.
2017.06
구독 인증기관 무료, 개인회원 유료
This paper analyzed structural behaviors of the staggered truss system, typically used in low seismicity regions, resisting the lateral loads such as wind and seismic load. A comparative study of cost and efficiency was carried out by analysing and designing the 10- and 20-story buildings with various types of truss, including pratt, howe, warren, K-, and vierendeel, which may typically be used in staggered truss system. In design, column and truss members are selected in group, and the efficiency of the member design was judged by average demand capacity ratio of the all members in same group. And economic analysis of the system was investigated by the quantity of the structural members. As a result, staggered truss system with the pratt truss and warren truss showed the most economical and efficient performance for 10-story building, and 20-story building, respectively.
4,000원
3.
2017.06
구독 인증기관 무료, 개인회원 유료
High voltage electric power transmitter GIS(Gas Insulated Switchgear) above 72.5kV needs to satisfy domestic Korean peninsular standard(ES-6110-0002) in KEPCO with respect to normal and special operation conditions which include internal gas pressure, dead weight, wind and seismic load. Some other requirements not described in Korean standard can be applied from other international standards such as IEC(International Electronical Committee) 62271-203 and 62271-207. The GIS is a kind of pressure vessel structure made of aluminum and filled with SF6 gas of internal pressure 0.4～0.5MPa. Finite element analysis of GIS is performed with such operational loads including seismic loading and the stability and reliability is determined according to ASME BPVC(Boiler and Pressure Vessel Code) SEC. VIII standard where the allowable stress level of the pressure vessel is suggested. The result shows that the stress of GIS is satisfied the allowable stress level and the safety factor is about 2.3 for Korean peninsular standard.
4,000원
4.
2017.06
구독 인증기관 무료, 개인회원 유료
In order to evaluate a stress state of concrete according to the change of tensile force of prestressed beam, improved nonlinear resonant ultrasonic spectroscopy(NRUS) method is proposed. This technique is advantageous to evaluate the stress state in initial state because the method shows much higher sensitivity than existing linear ultrasonic methods. The NRUS technique measure a nonlinearity parameter, which is calculated from the resonant frequency shift of ultrasonic wave related to the medium state, and the result is also closely related to the stress state of concrete. In this study, the nonlinearity parameter was measured with the change of tensile force to verify the close relationship between the two factors, and the effect of repetitive load cycle on the change of nonlinearity parameter was analyzed. In addition, sensitivity comparison with the linear ultrasonic pulse velocity method was performed. Through the experimental results, the possibility of NRUS technique for the evaluation of stress state in prestressed beam was confirmed.
4,000원
5.
2017.06
구독 인증기관 무료, 개인회원 유료
BIM(building information modeling) has been actively applied to construction industries and to maximize its application through the life cycle of structure, various relevant technologies have been proposed. In particular, 4D sequencing management and 5D cost-related management were introduced as an improved version of the design review and interface control by 3D information design. On the other hand, the virtual construction using virtual construction equipment can sophisticatedly handle capacity, dynamic movement, collision boundaries of actual construction machines but it still stays at a low level in a technical sense. In this study, simulation systems based on BIM involving virtual construction equipment have been developed; then it is applied to the actual construction project to evaluate the safety and efficiency of construction equipments. It was confirmed that the simulation systems can be utilized to construct virtual construction site by using an effective 3D library of construction equipment and can plays a key role to secure construction safety and economic feasibility. Specifically, the simulation system are very useful for decision making by construction managers to select the optimum equipment and construction method with a better understanding for safety and cost-saving.
4,000원
6.
2017.06
구독 인증기관 무료, 개인회원 유료
Using 3D based BIM(Building Information Modeling) enables a variety of construction simulations. The is no case to simulate BIM demonstration experiment on deeply immersed virtual reality environment in korea. This paper develops a multi screen based simulation system to enable 3D based immersed environment to diverse decision making and virtual construction simulation. In a developed simulation laboratory, we can carry out BIM drawing review, disaster evacuation simulation, constructability review on wild land and design urban planning using haptic device on 3-side space with 4K resolution . Also, It can review large amount of drawings without data conversion because of compatibility with BIM software.
4,000원
7.
2017.06
구독 인증기관 무료, 개인회원 유료
According to the structure, solenoid valve can be categorized as spool valve or poppet valve. While various research on spool valve which has simple structure and fine susceptibility to contamination has been conducted, poppet valve which has less susceptibility to contamination and advantage in a long time operation still need much research because of its complicated structure. In order to design the poppet valve, various parameters such as the diameter of the poppet, the angle of the poppet, the diameter of the disk, the spring stiffness, the spring preload and flow path structure should be considered. Conventional studies on poppet valve usually take only one design parameters and did not much focused on the effect of the parameters on flow characteristics. In this paper, the change of the flow characteristics according to the design parameters of the poppet valve for 3/2Way solenoid valve is analyzed. The previous studies and the results of initial model analysis was referred for the selection of the design parameters. The effects of design parameters on maximum pressure, minimum pressure, and pressure drop was examined using analysis of means(ANOM).
4,000원
8.
2017.06
구독 인증기관 무료, 개인회원 유료
The paper presents a new short-term dynamic displacement estimation method based on an acceleration and a geophone sensor. The proposed method combines acceleration and velocity measurements through a real time data fusion algorithm based on Kalman filter. The proposed method can estimate the displacement of a structure without displacement sensors, which is typically difficult to be applied to earthquake or fire sites due to their requirement of a fixed rigid support. The proposed method double-integrates the acceleration measurement recursively, and corrects an accumulated integration error based on the velocity measurement, The performance of the proposed method was verified by a lab-scale test, in which displacement estimated by the proposed method are compared to a reference displacement measured by laser doppler vibrometer (LDV).
4,000원
9.
2017.06
구독 인증기관 무료, 개인회원 유료
본 논문에서는 합성단면을 갖는 구조물의 극한 거동 해석에서 요구하는 재료 및 기하학적 비선형 해석을 수행하기 위한 보 요소를 제시하였다. 제안된 요소는 기하학적 비선형성을 효과적으로 모사할 수 있는 co-rotational 정식화를 통해 도출되 었으며, 다양한 합성단면의 저항성능을 재현할 수 있도록 화이버 단면법이 요소의 내력 및 강성을 산정하는데 활용되었다. 제안된 방법을 구현할 수 있도록 해석 프로그램이 개발되었으며, 호장법을 적용하여 최대내력 발생 이후의 연성거동뿐만 아 니라 심한 비선형 응답(snap-through 또는 snapback)까지 추적해낼 수 있도록 하였다. 본 연구에서 제안된 요소 정식화와 해석 프로그램의 정확성을 검증을 위해 몇 가지 수치예제가 수행되었고, 해석결과는 제안된 요소의 정확성과 효율성을 보이 기 위해 3차원 연속체 모델 및 기존 연구의 결과와 비교되었다. 추가로 합성단면을 갖는 골조 구조물에 대한 수치예제를 통 해, 합성단면을 구성하는 재료의 탄성계수 비 및 강도 비에 따른 영향을 분석하였다. 해석결과는 외층 재료의 탄성계수가 증 가됨에 따라 준취성 거동이 나타났으며, 외층 재료의 항복강도가 높을수록 선형 거동하는 기하적 비선형 응답과 유사한 응 답을 보였다.
4,000원
10.
2017.06
구독 인증기관 무료, 개인회원 유료
This study presents a sustainable design method to optimize the embodied energy and CO2 emission complying with the design code for reinforced concrete column. The sustainable design method effectively achieves the minimization of the environmental load and energy consumption whereas the conventional design method has been mostly focused on the cost saving. Failure of reinforced concrete column exhibits compressive or tensile failure mode against an external force such as flexure and compression; thus, optimization analyses are conducted for both failure modes. For the given sections and reinforcement ratios, the optimized sections are determined by optimizing cost, embodied energy, and CO2 emission and various aspects of the sections are thoroughly investigated. The optimization analysis results show that 25% embodied energy and 55% CO2 emission can be approximately reduced by 10% increase in cost. In particular, the embodied energy and CO2 emission were more effectively reduced in the tensile failure mode rather than in the compressive failure mode. Consequently, it was proved that the sustainable design method effectively implements the concept of sustainable development in the design of reinforced concrete structure by optimizing embodied energy consumption and CO2 emission.
4,000원
