This study was carried out to investigate the effects of planting densities on the growth characteristics, dry matter yield, and feed value of “Geukdong 6” (a new variety of corn for feed). The experimental design was arranged in a randomized block design with three replications. Treatments consisted of six planting densities, 60 cm × 25 cm (T1), 60 cm × 30 cm (T2), 70 cm × 25 cm (T3), 70 cm × 30 cm (T4), 80 cm × 25 cm (T5) and 80 cm × 30 cm (T6). All treatments were sown on May 14, 2021, and the harvest was on October 3 (late flowering). Plant length and the number of tillers were the highest in T5 (p<0.05), but the number of leaves and stem diameter were the highest in T6 than in the other treatments (p<0.05). Leaf length, leaf width, and dead leaf were not significantly different among the treatments. Organic matter was highest in T6, and crude protein was highest in T5 (p<0.05). The ether extract was not significantly different among the treatments. Crude fiber, NDF, and ADF were highest in T2 with relatively higher planting density (p<0.05). Calcium and phosphorus were not significantly different among the treatments. TDN content was the highest in T3 (p<0.05). Sugar degree (Brix), fructose, glucose, dextran, isomerose, and inverted sugar were not significantly different among the treatment. Fresh yield, dry matter yield and TDN yield were higher in order of T6 > T5 > T4 > T3 > T2 > T1 (p<0.05). Relatively feed value was higher in order of T3 > T6 > T5 > T1 > T4 > T2 (p<0.05). Based on the above results, planting density could be recommended from 80 cm × 30 cm for efficient production of “Geukdong 6”.

블록 매칭 및 3D 필터링(BM3D) 알고리즘은 단일 필터의 문제점을 보완하기 위하여 non-local means 기반으로 만들 어진 융합형 노이즈 제거 알고리즘이다. 하지만, 그 수식 인자의 조절에 관한 연구는 이루어지지 않고 있어 본 연구에서는 자기공명영상에서 발생하는 Rician 노이즈를 제거하기 위해 BM3D 알고리즘의 평활화 정도를 결정하는 노이즈 전력 스펙 트럼 밀도(noise power spectrum density,  )에 대한 최적화를 진행하고자 하였다. MRiLab 시뮬레이션 프로그램을 이 용하여 뇌 조직을 모사할 수 있는 뇌척수액(cerebrospinal fluid, CSF)/회색질(gray matter, GM)/백질(white matter, WM) 팬텀의 T1 강조영상을 획득하였고, 노이즈 레벨이 0.1, 0.15, 0.2, 0.25, 그리고 0.3인 Rician 노이즈를 각각 부가 한 후, BM3D 알고리즘의  값을 0.01부터 0.99까지 0.01씩 증가시키며 각각의 노이즈가 부가된 영상에 적용하였다. 정량 적 평가를 통해 최적화 값을 선정하기 위하여 CSF, GM, WM, 그리고 배경 영역에 관심 영역을 설정한 후 조직별 신호 대 잡음비(signal to noise ratio, SNR), 총 변동계수(coefficient of variation, COV), 그리고 평균 제곱근 오차(root mean square error, RMSE)를 측정하였다. 결과적으로, 조직별로 계산된 SNR, COV, 그리고 RMSE를 종합적으로 평가 했을 때 모든 조직에서 노이즈 레벨 0.1부터 0.3까지 증가함에 따라  값 또한 함께 증가하는 경향이 나타났으며 일정  값 이상에서는 노이즈뿐만 아니라 영상신호까지 함께 제거되어 개선 폭이 감소하는 것으로 관찰되었으며, 노이즈 레벨에 따라 각각 0.09, 0.13, 0.17, 0.21, 그리고 0.25의  값이 설정된 BM3D 알고리즘이 적용되었을 때 가장 합리적인 영상 특성을 보이는 것으로 나타났다. 결론적으로, 효과적인 노이즈 제거를 위해서 고정된 값이 아닌 노이즈 레벨에 따른 적합한 값을 적용해야 함을 증명할 수 있었다.

The spread of invasive alien plants is one of the most important causes of habitat and biodiversity loss. This research was conducted to secure basic data for the control of the invasive alien plant Solidago altissima. The following research objects were examined: the control; one-time mowing in June (1M6); twotime mowing in June and July (2M6M7); one-time mowing in Jun plus one-time Uprooting in July (2M6U7). The length growth in October, when the growth of S. altissima was completed, was in the order of control (199±19.96 cm), 1M6 (152±13.41 cm), 2M6U7 (54±3.17 cm), and 2M6M7 (45±19.96 cm). The 2M6M7 and 2M6U7 treatment was the most effective at inhibiting S. altissima of density, of 50.8% and 26.2% compared to the control, respectively. In contrast, one-time mowing (1M6) resulted in an increase in density compared to the control by 119.7%. In addition, this treatment also reduced flowering rate (%) of S. altissima. The most effective treatment among those tested was 2M6U7.

This study examines the surface characteristics, electrical conductivity, electromagnetic wave blocking characteristics, infrared (IR) transmittance, stealth function, thermal characteristics, and moisture characteristics of IR thermal imaging cameras. Nylon film (NFi), nylon fabric (NFa), and 5 types of nylon mesh were selected as the base materials for aluminum sputtering, and aluminum sputtering was performed to study IR thermal imaging, color difference, temperature change, and so on, and the relationship with infrared transmittance was assessed. The electrical conductivity was measured and the aluminum-sputtered nylon film demonstrated 25.6kΩ of surface resistance and high electrical conductivity. In addition, the electromagnetic wave shielding characteristics of the sputtering-treated nylon film samples were noticeably increased as a result of aluminum sputtering treatment as measured by the electromagnetic wave blocking characteristics. When NFi and NFa samples with single-sided sputtering were placed on the human body (sputtering layer faced the outside air) and imaged using IR thermographic cameras, the sputtering layer displayed a color similar to the surroundings, showing a stealth effect. Moreover, the tighter the sample density, the better the stealth function. According to the L, a, b measurements, when the sputtering layer of NFi and NFa samples faced the outside air, the value of a was generally high, thereby demonstrating a concealing effect, and the E value was also high at 124.2 and 93.9, revealing a significant difference between the treated and untreated samples. This research may be applicable to various fields, such as the military wear, conductive sensors, electromagnetic wave shielding film, and others.

The present study investigated effects of microbial additives and silo density on chemical compositions, fermentation indices, and aerobic stability of whole crop rice (WCR) silage. The WCR (“Youngwoo”) was harvested at 49.7% dry matter (DM), and ensiled into 500 kg bale silo with two different compaction pressures at 430 kgf (kilogram-force)/cm2 (LOW) and 760 kgf/cm2 (HIGH) densities. All WCR forage were applied distilled water (CON) or mixed inoculants (Lactobacillus brevis 5M2 and Lactobacillus buchneri 6M1) with 1:1 ratio at 1x105 colony forming unit/g (INO). The concentrations of DM, crude protein, ether extract, crude ash, neutral detergent fiber, and acid detergent fiber of whole crop rice before ensiling were 49.7, 9.59, 2.85, 6.74, 39.7, and 21.9%, respectively. Microbial additives and silo density did not affect the chemical compositions of WCR silage (p>0.05). The INO silages had lower lactate (p<0.001), but higher propionate (p<0.001). The LOW silages had higher lactate (p=0.004). The INO silages had higher yeast count (p<0.001) and aerobic stability (p<0.001). However, microbial counts and aerobic stability were not affected by silo density. Therefore, this study concluded that fermentation quality of WCR silage improved by microbial additives, but no effects by silo density.

Density of chloride molten salts is an essential physical property in the reactor core design and thermal-hydraulic design simulation, especially in molten salt reactor (MSR) design currently under development in Korea. NaCl-MgCl2-UCl3 pseudo-ternary system is one of the various candidate chloride-based salt mixtures because it has relatively-low melting point, very low vapor pressure, high thermal conductivity, etc. However, to the best of our knowledge, the density data of NaCl-MgCl2- UCl3 have not yet been measured or published worldwide, and therefore the ballpark figures of the density should be given for the preliminary reactor design. In our present study, the density estimation of NaCl-MgCl2-UCl3 based on the pseudo-binary data, i.e., NaCl-MgCl2, MgCl2-UCl3, and NaCl- UCl3, reported in the literature previously were performed using the Redlich-Kister model. Binary interaction parameter for MgCl2-UCl3 was higher than that for NaCl-MgCl2 and lower than that for NaCl-UCl3. As an example, calculated density of 0.62 NaCl: 0.18 MgCl2: 0.20 UCl3 at 873 K was 2.578 g·cm−3. In our further study, the methodology using Redlich-Kister model will be applied to more complex multicomponent systems and to other physical properties such as viscosity, thermal conductivity, surface tension, etc.

When disposing of spent nuclear fuel, there is a risk of exposure that could exceed the annual allowable dose due to human intrusion after the institutional control period. Therefore, it can be treated with the pyroprocess, but the decontamination factor is not sufficient, and an additional actinide recovery is required because molten waste salt-containing actinide is generated. In the case of reducing the element in the spent molten salt through an electrochemical method using a liquid Bi electrode, it is difficult to separate only the actinide element because the two-element groups are reduced together due to the large concentration difference between the actinide and the rare earth element. Therefore, a process of forming a Bi intermetallic compound using a liquid Bi electrode, which has higher element separation efficiency than a liquid Cd electrode, and physically separating the Bi intermetallic compound using the difference in density of the produced compound has been proposed. For this, it is necessary to understand the properties and density separation of the intermetallic compound to be produced, and experiments were planned and conducted for this purpose. Various metals were added to the molten Bi to form an intermetallic compound, and an analysis device such as SEM was used to determine the intermetallics distribution, composition, and internal structure. As the added metal, Ce is a representative element for lanthanide, and Hf with the most similar intermetallic density, decomposition temperature, and standard reduction potential to U, and U as a substitute element for actinide was adopted. As a result of SEM and EDS analysis, it was confirmed that the separation was made in Bi due to the density difference between the produced intermetallic compounds. A Ce-Bi intermetallic compound was observed in the upper part, Hf at a concentration smaller than the error range was detected, and a Hf-Bi intermetallic compound which containing high concentration of Ce was observed in the lower part. Separation of high-purity Ce seems to be possible in the upper part, and it seems difficult to separate high-purity Hf in the lower part. Therefore, to separate highpurity Hf, an additional process suitable for it seems to be necessary.

The purpose of this study is to present the direction of the plan to transform the residential complex into a space that can provide an open residential environment that can lead to social communication and exchange without being closed to the urban residential environment, especially in the apartment complex environment, which is becoming more dense. As a result of the Openness analysis of the ‘Codan Shinonome Canal Court’, the overall accessibility was good in terms of space utilization, and the openness was low in terms of the spatial composition, which is a physical environment due to the dense block type. When looking at the overall openness of the Codan Sinonome complex in terms of analysis by block, the corrected openness index (C.O.I) for all six blocks was 0.245, the corrected accessibility index (C.A.I) was 1.447 and the openness composite index (O.C.I) was assessed at 1.692. This was due to the formation of high-density block-type urban dwellings and the introduction of S-shaped streets and the layout of low-rise urban support facilities and commercial facilities. The Codan Sinonome Canal Court, which is considered an “open city residence,” quantitatively confirmed that it embodies macro-space structure and human-scale space environment even in high-precision environments.

바람에 의한 구조물의 진동은 관심대상이 되는 지배모드의 감쇠비에 매우 민감하다. 감쇠비의 발현 메커니즘의 불확실성 등 에 의해 감쇠비의 추정은 여전히 도전과제이며 보다 정확한 감쇠비 추정을 위한 연구가 지속되고 있다. 본 연구에서는 스펙트럼 밀도 적분함수라는 새로운 개념을 이용하여 구조물의 감쇠비를 추정하는 기법을 다룬다. 모드 응답스펙트럼에 포함된 외부하중 스펙트럼을 적분에 의한 평균화효과에 의해 평탄화 한 후 이론적 적분함수와 비교하여 감쇠비를 구하는 원리이다. 감쇠비 추출 가능성 탐색을 위 해 이론적 스펙트럼 밀도 적분함수의 특성을 분석하였으며, 비고전감쇠 시스템이 가지는 혼성 모드응답에 적용할 수 있는 감쇠비 추 정법로 확장하였다. 본 연구에서 제안된 감쇠비 추정법을 검증하기 위한 수치해석과 계측응답에 대한 적용이 이루어졌으며, 검증결과 제안된 감쇠비 추정법이 안정적이며, 신뢰도가 높은 감쇠비 추정이 가능함을 알 수 있었다.

The process optimization of directed energy deposition (DED) has become imperative in the manufacture of reliable products. However, an energy-density-based approach without a sufficient powder feed rate hinders the attainment of an appropriate processing window for DED-processed materials. Optimizing the processing of DEDprocessed Ti-6Al- 4V alloys using energy per unit area (Eeff) and powder deposition density (PDDeff) as parameters helps overcome this problem in the present work. The experimental results show a lack of fusion, complete melting, and overmelting regions, which can be differentiated using energy per unit mass as a measure. Moreover, the optimized processing window (Eeff = 44~47 J/mm2 and PDDeff = 0.002~0.0025 g/mm2) is located within the complete melting region. This result shows that the Eeff and PDDeff-based processing optimization methodology is effective for estimating the properties of DED-processed materials.

This study investigated the reaction between clay and Mn. Mn was coated using a manganese sulfate on porcelain plate and sintered from 1,100 oC to 1,250 oC. The body begin to shrink around 950 oC with the increase in temperature and rapidly progressed after 1,100 oC. Shrinkage of celadon body was performed at a lower temperature than for other substrates. Quartz, kaolin, and feldspar were the main crystalline phases of the starting materials, but they became mullite and crystobalite during the firing process, and some formed amorphous glass. When manganese sulfate was applied and fired, manganese oxide was fused, and some manganese oxide reacted with the substrate to show a dense microstructure different from that of the substrate; the substrate had pores. The manganese coated porcelain fired at 1,200 oC had L* values of 55.25, 36.87, and 37.13 for the white ware, celadon body, and white mixed ware, respectively; with a* values of 4.63, 3.07, and 2.15, and b* values of 7.93 and 3.98, it was found to be 3.42. This result indicated that the color of the surface was affected during firing by the chemical reaction between the substrate and manganese.

Ti-6Al-4V alloy has a wide range of applications, ranging from turbine blades that require smooth surfaces for aerodynamic purposes to biomedical implants, where a certain surface roughness promotes biomedical compatibility. Therefore, it would be advantageous if the high volumetric density is maintained while controlling the surface roughness during the LPBF of Ti-6Al-4V. In this study, the volumetric energy density is varied by independently changing the laser power and scan speed to document the changes in the relative sample density and surface roughness. The results where the energy density is similar but the process parameters are different are compared. For comparable energy density but higher laser power and scan speed, the relative density remained similar at approximately 99%. However, the surface roughness varies, and the maximum increase rate is approximately 172%. To investigate the cause of the increased surface roughness, a nonlinear finite element heat transfer analysis is performed to compare the maximum temperature, cooling rate, and lifetime of the melt pool with different process parameters.