A carbon fiber reinforced thermoplastic (CFRTP) was irradiated with a high energy electron-beam. As a result, the tensile strength of high-density polyethylene (HDPE)-based CFRTPs was significantly improved by gradually increasing the electron-beam dose. It was confirmed that the adhesion between CF and HDPE was improved and the surface properties of CF and HDPE were readily modified by electron-beam. It was verified from spectroscopic analysis that various oxygencontaining functional groups were formed on the surface of CF and HDPE by irradiation and we believe that strong attractive interactions took place among these functional groups at the interface of CFs and HDPE. Finally, it was conclusive that electron-beam irradiation provided two main effects on CFRTPs. One was cross-linking of thermoplastic resin for efficient load transfer from resin to CF and the other was formation of surface functional group and attractive interaction of these functional groups at the interface of fiber and matrix. These two effects showed synergetic contribution to enhance the mechanical properties of CFRTP.

한본 연구에서는, 철근콘크리트 보 구조물의 동결융해에 따른 장기거동특성 및 최종 파괴형태를 비교 분석하고자 하였다. 철근콘크리트 보 시험체와 재료 시험체를 제작하여, 동결융해 챔버를 이용하여 동결과 융해를 반복적으로 수행하였다. 동결융해를 위하여 기존의 시험법을 참고하여 철근콘크리트 구조물에 대한 시험을 수행 하였다. 동결융해에 따른 콘크리트의 재 료특성 변화와 철근콘크리트 보 구조물의 거동특성 변화를 통하여 동결융해에 대한 영향을 평가하였다. 제안된 동결융해 시험법을 통하여 콘크리트 공시체의 압축강도가 약 19%감소하였다. 철근콘크리트 보 시험체의 경우, 콘크리트의 표면 강도가 동결 융해에 의하여 감소되어 사인장 균열이 발생하여, 재료적 강도 감소에 의한 구조물의 성능이 감소함을 확인하였다. 또한, 사인장 균열이 발생한 동결융해 시험체의 에너지 소산능력이 동결융해를 거치지 않은 시험체와 비교하여 적게 발생하였다.

본 논문은 CFRP 쉬트로 휨 보강된 철근콘크리트 보에서 보강재의 탈락이 구조물에 미치는 영향을 파악하기 위한 실험적 그리고 해석적 연구결과를 보고한다. 실험적 연구로 CFRP 시트의 비부착 수준 및 위치를 실험변수로 고려한 실험체들에 대한 휨파괴 실험이 수행되었다. 중앙부에 비부착구간을 갖는 실험체의 경우 비부착구간의 증가에도 불구하고 최대하중 및 강성의 변화는 크게 감소하지 않았다. 단부에 비부착 구간을 갖는 실험체의 경우 비부착 구간이 증가할수록 최대하중 및 강성이 크게 감소하였다. 이것은 보강재의 작은 보강길이로 인한 정착력의 부족으로 인해 철근의 항복 이후 보강재가 조기 박리되었기 때문으로 판단된다. 본 연구의 결과와 기존 제안된 부착강도 모델을 이용한 예측 결과의 비교를 통해 기존 부착강도 모델들은 단부 비부착 실험체들보다 중앙 비부착 실험체들의 내하력을 더 정확하게 예측하는 것으로 나타났다.

In this study, the design of anchorage zone for unbonded post-tensioned concrete beam with single tendons of ultimate strength 2400MPa was evaluated to verify that the KDS 14 20 60(2016) and KHBDC 2010 codes are applicable. The experimental results showed that the bursting force equation of current design codes underestimated bursting stress measured by test, because the KDS 14 20 60(2016) and KHBDC 2010 propose the location of the maximum bursting force 0.5h which is the half of the height of member regardless of stress contribution. Although the allowable bearing force calculated by current design codes was not satisfied the prestressing force, the cracks and failure in anchorage zone was not observed due to the strengthening effect of anchorage zone reinforcement.

호박꽃과실파리(Zeugodacus scutellata)는 국내 자생종으로 국제적으로는 검역 대상 과실파리 중 하나로 분류되고 있다. 불임충방사기술 (sterile insect release technique (SIT))은 검역 대상 과실파리를 박멸하는 데 이용되어 왔다. 본 연구는 호박꽃과실파리를 대상으로 불임충 제조 기술을 개발하여 SIT 기술로 이 해충에 대한 방제 가능성을 분석하였다. 이에 앞서 먼저 형광현미경 기술로 호박꽃과실파리의 생식관련 기관을 관찰하였다. 다영양실형 난소소관을 갖는 1 쌍의 난소는 약 100 개의 난포를 발달시키며, 각 난포는 난모세포와 영양세포를 지니며 난포세포가 둘러싸는 구조를 지닌다. 난소 발육은 우화 후 10 일이 지나 발육을 시작하고 우화 후 20 일이 되면 난각을 가지고 있는 난모세포를 발달시켰다. 수컷의 경우 성숙된 정소가 우화 직후에 관찰되었으며 수정관에는 운동성이 있는 정자로 채워져 있었다. 불임 수컷을 제조하기 위해 다양한 선량(0~1,000 Gy)의 전자빔을 3~5 일 경과된 번데기에 조사하였다. 200 Gy 세기 전자빔으로 번데기에 조사하면 무처리와 차이 없이 성충으로 발육하였고 이후 정상 암컷과 교미행동을 보였다. 비록 이들 처리 수컷의 교미는 무처리 수컷과 비교하여 큰 차이 없는 산란력을 보였지만 산란된 알들은 부화하지 못했다. 다음으로 200 Gy 조사로 형성된 불임 수컷을 정상 암컷과 수컷이 함께 있는 장소에 방사하였다. 이때 불임충 수컷은 정상 수컷에 비해 9 배 많은 수로 방사하였다. 이러한 불임충 처리는 차세대 부화율을 현격하게 감소시켰다. 이상의 결과는 200 Gy 세기의 전자빔 으로 호박꽃과실파리의 불임충을 제조할 수 있고, 이렇게 형성된 불임충은 SIT 방제에 적용할 수 있다는 것을 제시하고 있다.

Monthly fluctuation in abundance and species composition of fish in coastal waters off Oenaro island, Goheung were investigated using seasonal samples collected by a shrimp beam trawl in 2018. A total of 5,981 fishes were sampled and classified into 48 species, 32 families, and 9 orders. The dominant species was Engraulis japonicus (993 individuals, 16.60%), Amblychaeturichthys hexanema (844 individuals, 14.11%), and Thryssa kammalensis (674 individuals, 11.27%). The highest number of individuals was found in August (958 individuals), while the lowest number of individuals was found in January (136 individuals). The diversity index was the highest in November (H’ = 2.37) and the lowest in January (H’ = 1.77).

In this study, a high speed planing boat with 7.2 meters in length is developed as the beam larger about 10% by comparing with the general planing boat. The design speed of a boat is 30 knots (about 15.4 m/s) by using 150 hp outboard engine and the main material is FRP. The resistance performance related to the free running attitude as trim and sinkage is discussed and the wave patterns are observed to clear the relationship between the performance and wave characteristics by model test. The turning circle is estimated by Lewandowski´s equation. The results show that not only the wave pattern but also the free running attitude of the boat have the strong influence on a resistance performance. The boat needs smaller engine power and has more stable running attitude because of large sinkage and small variation of trim due to the large area for the lift force and light weight.

This paper discusses the influence of transverse reinforcement spacing and support width of concrete wide beam on shear performance. In order to evaluate the shear performance, a total of thirteen specimens were constructed and tested. The transverse reinforcement spacing, the number of legs and support width were considered as variables. From the test results, the shear strength equation of concrete wide beam is proposed for prediction of shear strength of concrete wide beam to consider the transverse reinforcement spacing and support width. It is shown that the proposed equation is able to predict shear strength reasonably well for concrete wide beam.

In this study, we investigate the effect of Al/N source ratios and growth rates on the growth and structural properties of AlN films on c-plane sapphires by plasma-assisted molecular beam epitaxy. Both growth rates and Al/N ratios affect crystal qualities of AlN films. The full width at half maximum (FWHM) values of (1015) X-ray rocking curves (XRCs) change from 0.22 to 0.31° with changing of the Al/N ratios, but the curves of (0002) XRCs change from 0.04 to 0.45° with changing of the Al/N ratios. This means that structural deformation due to dislocations is slightly affected by the Al/N ratio in the (1015) XRCs but affected strongly for the (0002) XRCs. From the viewpoint of growth rate, the AlN films with high growth rate (HGR) show better crystal quality than the low growth rate (LGR) films overall, as shown by the FWHM values of the (0002) and (1015) XRCs. Based on cross-sectional transmission electron microscope observation, the HGR sample with an Al/N ratio of 3.1 shows more edge dislocations than there are screw and mixed dislocations in the LGR sample with Al/N ratio of 3.5.

The ion-beam irradiated lanthanum zinc oxide (LZO) films were conducted as liquid crystal (LC) alignment layer to achieve uniform and homogeneous alignment of LC molecules. Polarized optical microscopy and the pre-tilt angle measurements revealed the alignment characteristics of LC molecules on the LZO film surface. Physical characteristics of the LZO film surface were analyzed by field emission scanning electron microscope and atomic force microscopy. The strong ion-beam irradiation on the LZO film changed surface rougher than before and induced physical anisotropic characteristics. Chemical composition of the LZO film was investigated by X-ray photoelectron spectroscopy and it was revealed that the ion-beam irradiation induced the breakage of the metal-oxide bonds. Due to this, anisotropic dipole moment which related with van der Waals force between LC molecules and alignment layer was induced. Because of this, LC molecules were anchored to the LZO film surface to achieve uniform LC alignment. Collecting the capacitance-voltage curve, residual DC of the LC cell with the LZO films was measured and it was verified that the LC cell with the LZO film had a nearly zero residual DC. Therefore, the ion-beam irradiated LZO film is an efficient method as an LC alignment layer