제8차 전력수급기본계획에 근거하여 현재 운영중이거나 계획중인 원자력발전소에서 발생할 사용후핵연료의 양과 특성을 추정하였다. 본 연구에서 고려된 특성은 핵연료집합체에 대한 제원, 핵연료봉 배열, 235U 초기 농축도, 방출연소도, 냉각기간이다. 이들은 사용후핵연료 처분시스템을 설계하는데 필수적인 항목이다. 2082년까지 가압경수로 사용후핵연료의 예상발 생량은 약 62,500 다발로 추정되었다. 2018년 말까지 발생한 사용후핵연료 중 상대적으로 길이가 짧은 웨스팅하우스형 원전 연료가 약 60%, 상대적으로 길이가 50 cm 정도 긴 한국형 원전 연료가 약 40%를 차지하였다. 235U 초기 농축도 4.5 wt% 이 하를 갖는 사용후핵연료의 비율은 전체 발생량의 약 90%를 차지하였으며, 방출연소도는 98%의 물량이 55 GWd/tU 이하로 나타났다. 2077년을 기준으로 웨스팅하우스형 원전에서 발생한 사용후핵연료의 냉각기간은 50년 이상이 97% 정도를 차지하였으며, 본 논문에서 가정한 처분 완료시점인 2125년을 기준으로 한국형 원전에서 발생한 사용후핵연료의 냉각기간은 45 년 이상이 98% 정도를 차지하는 것으로 나타났다. 이러한 결과를 바탕으로 효율적인 처분시스템 설계를 위해 기준 사용후 핵연료는 제원적 특성을 고려하여 두 가지 형태로 설정하였으며, 웨스팅하우스형 원전 연료의 경우, 집합체 제원으로 KSFA, 초기 농축도 4.5 wt%, 방출연소도 55 GWd/tU, 냉각기간 50년으로, 한국형 원전 연료의 경우, 집합체 제원으로 PLUS7, 초기 농축도 4.5 wt%, 방출연소도 55 GWd/tU, 냉각기간 45년으로 설정하였다.

The purpose of this study is to provide basic data for setting environmental design standards for domestic greenhouses. We conducted experiments on thermal environment measurement at two commercial greenhouses where hot water heating system is adopted. We analyzed heat transfer characteristics of hot water heating pipes and heat emission per unit length of heating pipes was presented. The average air temperature in two greenhouses was controlled to 16.3oC and 14.6oC during the experiment, respectively. The average water temperature in heating pipes was 52.3oC and 45.0oC, respectively. Experimental results showed that natural convection heat transfer coefficient of heating pipe surface was in the range of 5.71~7.49W/m2 oC. When the flow rate in heating pipe was 0.5m/s or more, temperature difference between hot water and pipe surface was not large. Based on this, overall heat transfer coefficient of heating pipe was derived as form of laminar natural convection heat transfer coefficient in the horizontal cylinder. By modifying the equation of overall heat transfer coefficient, a formula for calculating the heat emission per unit length of hot water heating pipe was developed, which uses pipe size and temperature difference between hot water and indoor air as input variables. The results of this study were compared with domestic and foreign data, and it was found to be closest to JGHA data. The data of NAAS, BALLS and ASHRAE were judged to be too large. Therefore, in order to set up environmental design standards for domestic greenhouses, it is necessary to fully examine those data through further experiments.

국내 고층 아파트의 구조시스템은 크게 다수의 벽체가 분산적으로 배치되어 있는 내력벽 시스템과 중앙 코어벽 시스템으 로 구분할 수 있다. 각각 시스템에 따른 횡방향 거동을 분석하기 위해 본 연구는 국내 고층 아파트 중 대표적인 평면을 갖는 대상 건물을 선정하고, 비선형 정적해석을 수행하여 붕괴메커니즘을 살펴보았다. 비선형 정적해석을 통해 도출된 힘-변위 관계로부터 지진응답에 있어서 중요한 요소인 초과강도계수 및 연성도계수를 산정하여 반응수정계수를 평가하였다. 중앙 코어벽 시스템은 연성도는 작지만, 풍하중에 의해 지배되어 초과강도가 크게 산정돼 초과강도계수에 의해 반응수정계수가 산정되었고, 내력벽 시스템은 벽량이 많아 연성도가 크기 때문에 상당힌 큰 반응수정계수가 산정된다.

In this study, the seismic response is investigated by using a relatively low-rise building under torsion-prone conditions and three seismic loads with change of the location of the seismic isolation system. LRB (Lead Rubber Bearing) was used for the seismic isolator applied to the analytical model. Fixed model without seismic isolation system was set as a basic model and LB models using seismic isolation system were compared. The maximum story drift ratio and the maximum torsional angle were evaluated by using the position of the seismic layer as a variable. It was confirmed that the isolation device is effective for torsional control of planar irregular structures. Also, it was shown that the applicability of the midstory seismic isolation system. Numerical analyses results presented that an isolator installed in the lower layer provided good control performance for the maximum story drift ratio and the maximum torsional angle simultaneously.

관광지 및 공공공간에서의 사인 시스템은 대상지에서의 즉각적이고 명확한 정보 안내는 물론 현장에서의 다양한 이용자 계층을 고려한다는 측면에서 여전히 중요한 과제로 남아 있다. 본 연구는 대표적 한국전통문화 관광지의 하나인 한국민속촌을 대상으로 정체성, 통일성, 가독성, 내구성, 위치의 적합성 등 5가지 조성원칙에 입각하여 문제점을 분석하였다. 이를 위해 사인시스템에 대한 문헌분석, 한국민속촌 사인시스템의 현황조사와 더불어 실제 이용자 150명을 대상으로 현장 설문조사를 실시하였으며, 이를 바탕으로 각각의 조성원칙이 전반적인 사인 이용 만족도와 어떤 상관성을 갖는지에 대해 분석하였다. 정체성, 통일성, 가독성, 내구성, 위치의 적합성 등 사인시스템의 5가지 주요 원칙들과 사인의 이용만족도와의 상관관계를 파악하기 위해 Pearson 상관계수 분석을 실시하였으며 그 결과, 한국민속촌의 경우 통일성과 가독성이 사인의 이용만족도와 통계적으로 유의한 상관관계가 있었으며 내구성과 위치의 적합성은 사인의 이용만족도와 낮은 상관성을 보였다. 5개의 주요 요소들간에는 정체성과 통일성이 가장 높은 상관관계를 보였으며, 통일성과 가독성, 정체성과 위치의 적합성도 유의한 상관관계를 나타냈다.

The purpose of this study is to create a new odor analysis technology that combines the separation technology of GC and the measurement of MOS sensors. The detector of the GC system is replaced with the MOS sensor to analyze various odor compounds. Carrier gas also used air in the normal atmosphere through a micro pump. Therefore, it is possible to develop a portable odor analysis device since no additional cylinder is needed. Retention times for H2S, C7H8, and C2H4O analyzed by the combined GC/MOS system were identified as 1.28 minutes, 3.88 minutes and 1.77 minutes, respectively. Measurement reproducibility of odorous RT was very good at less than 1.2 %RSD. Also, the magnitude of the peak as a result of changes in the concentration of each odor showed a linear proportional relationship. Thus, a new method could be proposed to analyze various odorous substances with the combined GC/MOS system.

In this paper, we compared and analyzed the performance of the GPS L1/L2 signal with GPS L1 using the navigation system. Generally the GPS receiver calculates the position of the satellite by using the ephemeris data recevied from GSP Satellites, and also calculates the position of its own using the pseudorange. This paper provides an overview of the device which can receive an GPS L1/L2, and compares the GPS L1 with the GPS L2 signal power using the simulator. It was confirmed that the GPS L1/L2 receiver and the GPS L1 receiver met the requirements of standards and it is similar to the navigation performance of the GPS L1 Receiver with the GPS L1/L2 receiver. It was also confirmed that the GPS L2 band can not correct ionospheric error in the navigation system of the combat vehicle.

본 연구에서는 변량방제기술을 적용한 농용 회전익기를 이용하여 살포한 입자의 구간비행 상태에서의 거리별 살포 패턴을 측정함으로써 무인 항공방제의 농약 부착률과 입자경의 분포 균일도를 평가하였다. 비행을 등속으로 유지하는 안내비행과 자동비행 모드에서 유효살포폭 3.6m로 인접비행 구간과 살포폭이 일부 중첩된 피복률에 대한 가로방향 분포의 변이계수는 30% 정도를 보였고, 비행방향 진로위치에 대한 피복률의 변이계수는 10% 미만으로 매우 균등한 것으로 평가되었다. 따라서 살포작업시 기체의 지면속도(ground speed)의 변이를 보상하는 변량살포기술은 균일도 측면에서 우수한 것으로 판명되었으며, 또한 입자경의 분포에 있어서 체적중위직경(VMD)과 개체중위직경(NMD) 모두 항공방제에 적절한 크기와 균일한 분포를 보였다. 따라서 농용 회전익기를 이용하여 소필지의 항공방제작업을 무인화 하는 데 있어, 변량방제장치를 적용함으로써 소규모 필지의 균일 정밀방제를 도모하고자 하였다.

Seismic isolation systems have typically been used in the form of base seams in mid-rise and low-rise buildings. In the case of high-rise buildings, it is difficult to apply the base isolation. In this study, the seismic response was analyzed by changing the installation position of the seismic isolation device in 3D high - rise model. To do this, we used 30-story and 40-story 3D buildings as example structures. Historic earthquakes such as Mexico (1985), Northridge (1994) and Rome Frieta (1989) were applied as earthquake loads. The installation position of the isolation device was changed from floor to floor to floor. The maximum deformation of the seismic isolation system was analyzed and the maximum interlaminar strain and maximum absolute acceleration were analyzed by comparing the LB model with seismic isolation device and the Fixed model, which is the base model without seismic isolation device. If an isolation device is installed on the lower layer, it is most effective in response reduction, but since the structure may become unstable, it is effective to apply it to an effective high-level part. Therefore, engineers must consider both structural efficiency and safety when designing a mid-level isolation system for high-rise buildings.

In this study, various physical cleaning methods such as physical washing and osmotic backwash, were performed to understand membrane fouling characteristics by employing real secondary wastewater effluent (SWWE). In addition, microfiltration (MF) and ultrafiltration (UF) pretreatments were compared to maximize removal of organic matter and to control membrane fouling efficiently. Organic foulants deposited on the active layer of FO membrane were observed by fouling behavior test. The relationship between concentrations of natural organic matter and membrane fouling was also investigated from the bench-scale FO tests. Finally, by quantitative analysis of correlations between foulants and fouling reversibility with the modified fouling index (MFI), we identified the applicability of MFI in predicting FO intake water fouling potential.

Using a theoretical framework of cultural capital, the present study analyzed a collecting system in AbyssRium, a mobile healing game. AbyssRium provides users with emotional satisfaction by allowing them to decorate a virtual aquarium using fishes and other sea creatures. We conducted a content analysis using contents generated in online communities and focus group interview with heavy users of AbyssRium. Results suggest that game players feel superiority by possessing rare fishes over others. These rare items were also utilized to distinguish users who collected the items from others not possessing such fishes. Also, the game operator of AbyssRium maintains the game balance by imposing greater costs for experienced users than for novice users in collecting fishes and decorate the aquarium. Such a strategy contributes to sustaining the social ecosystem of Abyssrium by encouraging new users to start to play the game. The current study suggests that a simple mobile game can afford a social interaction and a social system allowing users to constructs social meaning of artifacts presented in the virtual environments. Future research may broaden the generalizability of the cultural capital framework by replicating these findings in different video games.

In order for the probe to perform ocean exploration and survey research, it is necessary to adjust the position of the ship as desired by dynamic positioning system. The dynamic positioning system of T/S NARA is applied to K-POS dynamic positioning system of Kongsberg, which makes maintaining the ship's position, changing position and heading control possible. T/S NARA is not capable of dynamic positioning if one or more propulsive forces are lost with DP Level One. However, it is predicted that dynamic positioning can be achieved even at the time of missing one thrust in a good sea condition. Therefore, we want to analyze the effect of each propulsion on the performance of dynamic position system. When one of the bow thruster and azimuth thrusters lost their propulsion, maintaining the ship's position, changing position and heading control performance were compared and analyzed. If the situation occurred disable from using the bow thruster, they can not maintain ship's position. Azimuth thruster was influential for the ship's position control and bow thruster was influential in heading control. The excellent dynamic positioning performance can be achieved, considering the propulsion power that will have a impact on each situation in the future.

This study aimed to analyze the profitability and economic feasibility of hairtail trolling line gear that was developed for the last 3 years (2015-2017). The new fishing gear technology development was accomplished to solve the current problem of fishermen shortage in hairtail targeting fisheries in Jeju region. Results indicated that the profitability of developed hairtail trolling line fishery was estimated to be 36.1 % which would be higher than that of other hairtail targeting fisheries in Jeju region. In addition, as an economic feasibility, the net present value and the internal rate of return of a 20-year cash inflow and outflow were evaluated to be 400.2 million won and 66.9 %, respectively. However, sensitivity analyses of main variables showed that the profitability and economic feasibility would be vulnerable to catch amount and market condition changes.

Background: There are insufficient objective or quantitative evidence for the better intervention to improve proprioception particularly for the application of external load. There are conflicting opinions whether the external load is effective for proprioception improvement or not. Objects: The purpose of this study was to investigate effects of external load on proprioception of shoulder joint quantitatively using 3D motion capture system. Methods: Nine healthy adults joined for this study. They were asked to perform scapular plane abduction motion with attaching reflective markers on the trunk and upper limb. The 3D positions of finger marker, while they performed the same task with and without external load, were recorded and analyzed. Results: All participants showed decreased variable errors in the vertical direction when the external load was applied (p<.02). Even though other directions (y, z) and absolute errors increased, they did not have statistical significances. Conclusion: Based on this study results, the external load application would be effective for shoulder joint position sense improvement.

Core/shell CdSe/ZnS quantum dots (QDs) are synthesized by a microfluidic reactor-assisted continuous reactor system. Photoluminescence and absorbance of synthesized CdSe/ZnS core/shell QDs are investigated by fluorescence spectrophotometry and online UV-Vis spectrometry. Three reaction conditions, namely; the shell coating reaction temperature, the shell coating reaction time, and the ZnS/CdSe precursor volume ratio, are combined in the synthesis process. The quantum yield of the synthesized CdSe QDs is determined for each condition. CdSe/ZnS QDs with a higher quantum yield are obtained compared to the discontinuous microfluidic reactor synthesis system. The maximum quantum efficiency is 98.3% when the reaction temperature, reaction time, and ZnS/CdSe ratio are 270℃, 10 s, and 0.05, respectively. Obtained results indicate that a continuous synthesis of the Core/shell CdSe/ZnS QDs with a high quantum efficiency could be achieved by isolating the reaction from the external environment.