우리는 콘크리트 세상 속에 살고 있다고 해도 과언이 아니다. 콘크리트 도로를 달리고 콘크리트 건 물 속에서 살고 있다. 그런데 최근 노후화된 구조물의 붕괴 사례들이 지속적으로 발생하고 있으며 이 에 대한 원인 규명과 재발 방지, 그리고 기술적 사전 예측 등이 필요하다. 특히 우리나라의 경우 4계 절의 영향을 받는 철근콘크리트 구조물은 시간이 흐름에 따라 다양한 열화로 인해 강도가 저하되고, 이로 인해 건축물의 심각한 손상 및 붕괴가 발생하게 된다. 전국적으로 기온이 영하로 내려가는 겨울 철에는 동결융해의 영향으로 인한 강도 저하로 노후화가 진행되며, 콘크리트의 공기율에 따라 동결융 해로 인한 노후화 정도가 달라지게 된다. 이는 콘크리트 공기율에 따라 내구성지수가 변화하여 동결융 해의 영향 정도가 변화하기 때문이다. 그러나 기존의 콘크리트에 관한 동결융해 영향 연구는 재료에 대한 연구가 많지만, 상대적으로 큰 철근콘크리트 부재 단위에 대한 연구는 부족하다. 따라서 본 연구 에서는 철근콘크리트 부재를 대상으로 기중 동결융해 시험 방법을 통해 콘크리트의 공기율이 증가함 에 따른 재료 단위의 영향과 철근콘크리트 부재의 휨 거동 특성에 대한 영향을 분석하고자 한다.본 연 구에서는 동결융해를 입은 콘크리트가 공기율이 증가함에 따라 동탄성계수와 내구성지수를 비교하고, 이에 따른 압축강도 실험을 통해 동결융해의 영향을 평가하였으며 철근콘크리트 부재의 휨 실험을 통 해 동결융해가 콘크리트 공기율에 대하여 거동 특성, 탄성 강성 및 항복까지의 에너지 흡수 능력에 미 치는 영향을 비교하여 분석하였다. 또한 ABAQUS 해석 프로그램을 사용하여 유한요소 모델을 제안하 고 휨 거동 성능을 실험값과 비교하여 분석하였다.

Restraints of Branch Lines are used as earthquake-resistant support devices for fire-fighting pipes along with sway brace devices. The central types are aligned and fixed in a straight line with center of the pipe, but the eccentric types are fixed to on side of the pipe, so a bending moment occurs. In this study, three specimens each of central type and eccentric type were installed at an angle of 45° from the vertical and a monotonic compression load of 1340N was applied. All central type samples satisfied 17.8mm of the allowable displacement, but all eccentric type samples failed to meet the target load and buckled. Therefore, when considering the performance of eccentric type restraints, both compressive load and bending moment must be considered. Even through material mechanics calculations, the yield stress of eccentric type - 3/8 inch all threaded steel bolt - exceeds 320Mpa of the allowable stress. A experiment standards need to be established for eccentric type restraints.

In this study, a prefabricated buckling brace (PF-BRB) was proposed, and a test specimen was manufactured based on the design formula for the initial shape and structural performance tests were performed. As a result of the experiment, all standard performance requirements presented by KDS 41 17 00 and MOE 2021 were satisfied before and after replacement of the reinforcement module, and no fracture of the joint module occurred. As a result of the incremental load test, the physical properties showed a significant difference in the stiffness ratio after yielding under the compressive load of the envelope according to the experimental results. It is judged necessary to further analyze the physical properties according to the experimental results through finite element analysis in the future.

In piping systems, trapeze hangers are subjected to vertical and horizontal seismic loads and stiffeners are used. In this study, monotonic compression tests were conducted with the removable stiffeners using three variables: stiffener clamp fixing position, section length, and installation direction. The maximum load reinforced with stiffeners could withstand a compressive load of 11kN by applying a safety factor of 10%. It could be estimated that the fixing clamp spacing or the length of shape and load had a proportional relationship. And the stiffener must be fixed in the direction of the strong axis on hinge parts. Also the stiffener buckiling load design proposes to use a method of calculate the flexural buckling compressive strength of and unreinforced full threaded bolt.

실험 계획법을 활용하여 세라마이드가 고함량으로 함유된 수화 액정형 베시클의 입자 사이즈에 영향을 미치는 인자를 분석하고 혼합물 조성의 최적화를 시도하였다. 베시클 입자 사이즈에 영향을 주는 주요 변수로 제조 온도, 에탄올 양, 초음파 시간을 각각 정하고, 다구찌 방법의 S/N비 산출과 ANOVA 분 석을 통해, 이들 변수들이 입자 사이즈에 미치는 영향을 살펴보았다. 또한 혼합물 실험 계획법의 심플렉스 중심 설계에 따라, 베시클 막을 구성하는 세 지질 성분, 인지질(HPC), 콜레스테롤(Chol), 세라마이드(Cer) 의 혼합 조성 실험을 수행하였다. 실험에서 얻어진 데이터로부터 회귀분석을 실시하여 모델식을 구하고, 베시클 입자 사이즈를 최소로 만들기 위한 세 지질 성분의 최적 혼합 조성은 HPC(0.6), Chol(0.1), Cer(0.3)으로 구해졌다.

본 연구에서는 3D 프린팅 FDM 방식의 적층 방향에 따라 기계적 물성이 달라지는 이방성 특성을 확인하고 이를 이용하여 위상 최 적설계를 수행하였다. 벤치마크 문제인 자동차 현가장치 부품 중 하나인 로어 컨트롤 암에 대하여 밀도법 기반 위상 최적설계를 수행 하였으며, 외부 하중과 이방성 특성에 따라 위상 최적결과가 다르게 나타나는 것을 확인하였다. 이를 이용하여 최적화된 모델에 대하 여 3D 프린터로 적층 방향을 달리하여 2가지 시험품을 제작하였으며 인장시험을 수행하였다. 시험시 3D 비접촉 변형률 측정기를 이 용하여 변형률을 구하였으며 이를 CAE 응답해석으로 얻은 변형률과 비교한 결과가 정량 및 정성적으로 일치하는 것을 확인하였다. 3D 프린팅 적층 방향을 고려한 위상 최적모델의 인장 실험 결과를 통해 해당 최적설계 방법론의 유효성을 검증하였다.

본 연구에서는 20,000 톤급 해양플랜트 상부구조물(Topside)의 플로트오버 설치작업을 위해 개발된 수동형 갑판 지지 프레임 (Deck support frame)의 구조설계에 대해 다양한 실험계획법을 이용한 최소중량설계와 민감도 평가의 비교연구를 수행하였다. 수동형 갑판 지지 프레임의 주요 구조부재의 두께 치수 변수는 설계인자로 고려하였고, 응답치는 중량과 강도성능으로 선정하였다. 최소중량설계와 민감도 평가의 비교연구에 사용한 실험계획법은 직교배열설계법, Box-Behnken 설계법, 그리고 Latin hypercube 설계법이다. 실험계획법의 설계공간 탐색의 근사화 성능을 평가하기 위해 반응표면법을 각 실험계획법 별로 생성하여 근사화 정확도 특성을 검토하였다. 또한 최소 중량설계를 위해 최상 설계안의 결과로 부터 실험계획법의 특성에 따른 수치계산 비용, 중량감소 효과 등을 평가하였다. 수동형 갑판 지지 프레임의 구조설계에 대해 Box-Behnken 설계법이 가장 적합한 설계 결과를 나타내었다.

In previous studies, the pressure distribution on optical mirror surface was measured by CFD analysis assuming various external air conditions on optical structures designed using knowledge-based design techniques. In this study, the KBD model was verified by comparing the pressure data from the mirror surface obtained through CFD analysis with the pressure values from the wind tunnel test of the actual model.

In this study, a motion control problem for the vessel towed by towing ship on the sea is considered. The towed vessel does not have self-control capabilities such that its course stability totally depends on the towing ship. Especially, in the narrow canal, river and congested harbor area, extreme tension is required during the towing operation. The authors, therefore, propose a new control system design method in which the rudder is activated to provide its maneuverability. Based on the leader following system configuration, a nonlinear mathematical model is derived and a backstepping control is designed. By experiment results with nonlinear control framework, the usefulness and effectiveness of the proposed strategy are presented.

In this study, a field bridge test was conducted to find the dynamic properties of cable supported bridges with resilient-friction base isolation systems (R-FBI). Various ambient vibration tests were performed to estimate dynamic properties of a test bridge using trucks in a non-transportation state before opening of the bridge and by ordinary traffic loadings about one year later after opening of the bridge. The dynamic properties found from the results of the tests were compared with an analysis model. From the result of the ambient vibration tests of the cable supported bridge with R-FBI, it was confirmed that the dynamic properties were sensitive to the stiffness of the R-FBI in the bridge, and the seismic analysis model of the test bridge using the effective stiffness of the R-FBI was insufficient for reflecting the dynamic behavior of the bridge. In the case of cable supported bridges, the seismic design must follow the “Korean Highway Bridge Design Code (Limit State Design) for Cable supported bridges.” Therefore, in order to reflect the actual behavior characteristics of the R-FBI installed on cable-supported bridges, an improved seismic design procedure should be proposed.

In this study, the design of anchorage zone for unbonded post-tensioned concrete beam with single tendons of ultimate strength 2400MPa was evaluated to verify that the KDS 14 20 60(2016) and KHBDC 2010 codes are applicable. The experimental results showed that the bursting force equation of current design codes underestimated bursting stress measured by test, because the KDS 14 20 60(2016) and KHBDC 2010 propose the location of the maximum bursting force 0.5h which is the half of the height of member regardless of stress contribution. Although the allowable bearing force calculated by current design codes was not satisfied the prestressing force, the cracks and failure in anchorage zone was not observed due to the strengthening effect of anchorage zone reinforcement.

Conventional rotary sawing machine for cutting lumber generates severe amount of dust scattering to the environment. In this research, the design improvement of the rotary sawing machine is achieved to significantly reduce the dust scattering by the design process utilizing computational fluid dynamics (CFD) analysis. Several design candidates for the design improvement of the rotary saw system were proposed and modeled, and CFD analyses were performed to choose the best design in viewpoint of the least dust scattering. CFD analysis proved to be very useful to predict the characteristics of the air flow inside the saw system. The movement of dust particles with the air flow during the sawing process was analyzed for various design features of the saw system. The most efficient design to minimize the amount of dust particles ejected from the saw system was chosen based on the CFD analysis results. Then, the prototype of the best candidate of the improved rotary saw machine was built and the amount of dust particles were measured to verify its performance.

The algal blooms in stagnant streams and lakes have caused many problems. Excessive algae leads to disturbance of ecosystem and overload of water treatment processes. Therefore, phosphorus(P), source of algal blooms, should be controlled. In this study, a filtration trench has been developed to convert dissolved phosphorus into hydroxyapatite(HAP) so that it could be crystallized on the surface of ‘phosphorus removal granular material’; and residual particulate phosphorus could be removed by additional precipitation and filtration. The front and rear parts of filtration trench consisted of ‘phosphorus removal granular material contact bed’ and ‘limestone filtration bed’, respectively. As a result of the column test using phosphorus removal granular material and limestone serially, PO4-P was removed more than 90% when EBCT(empty bed contact time) of the contact bed was over 20 minutes; and T-P represented 60% of removal efficiency when total EBCT was over 1.5 hours. The results of column tests to figure out the sedimentation characteristics showed that more than 90% of particulate phosphorus could be removed within 24 hours. It was necessary to optimize the filtration part in order to increase removal efficiency of T-P additionally. Also, it was confirmed through the simulation of Visual MINTEQ that most of particulate phosphorus in the column tests is the form of HAP. Based on the results of the study, it could be suggested that the design parameters are over 0.5 hour of EBCT for phosphorus removal granular material contact bed and over 1.5 hours of EBCT for limestone filtration bed.

Water quality improvement processes for stagnant area consist mainly of technologies applying vegetation and artificial water circulation, and these existing technologies have some limits to handle pollution loads effectively. To improve the purification efficiency, eco-friendly technologies should be developed that can reinforce self-purification functions. In this study, a multi-functional floating island combined with physical · chemical · biological functions (① flotation and oxidization using microbubbles, ② vegetation purification and ③ bio-filtration with improved adsorption capacity) has been developed and basic experiments were performed to determine the optimal combination conditions for each unit process. It has been shown that it is desirable to operate the microbubble unit process under conditions greater than 3.5 kgf/cm2. In vegetation purification unit process, Yellow Iris (Iris pseudacorus) was suggested to be suitable considering water quality, landscape improvement and maintenance. When granular red-mud was applied to the bio-filtration unit process, it was found that T-P removal efficiency was good and its value was also stable for various linear velocity conditions. The appropriate thickness of filter media was suggested between 30 and 45 cm. In this study, the optimal design and operating parameters of the multi-functional floating island have been presented based on the results of the basic experiments of each unit process.