The government declared ‘2050 carbon neutrality’ as a national vision in October 2020 and subsequently pursued the establishment of a ‘2050 carbon neutrality scenario’ as a follow-up response. Hydrogen is considered as one of the most promising future energy carriers due to its noteworthy advantages of renewable, environmentally friendly and high calorific value. Liquid hydrogen is thus more advantageous for large-scale storage and transportation. However, due to the large difference between the liquid hydrogen temperature and the environment temperature, an inevitable heat leak into the storage tanks of liquid hydrogen occurs, causing boil-off losses and vent of hydrogen gas. Researches on insulation materials for liquid hydrogen are actively being conducted, but research on support design for minimal heat transfer and enhanced rigidity remains insufficient. In this study, to design support structures for liquid hydrogen storage tanks, a thermal-structural coupled analysis technique was developed using Ansys Workbench. Analytical models were created based on the number and arrangement of supports to propose structurally safe support designs.

Hydrogen is considered as one of the most promising future energy carriers due to its noteworthy advantages of renewable, environmentally friendly and high calorific value. However, the low density of hydrogen makes its storage an urgent technical problem for hydrogen energy development. Compared with the density of gas hydrogen, the density of liquid hydrogen is more than 1.5 times higher. Liquid hydrogen is thus more advantageous for large-scale storage and transportation. However, due to the large difference between the liquid hydrogen temperature and the environment temperature, an inevitable heat leak into the storage tanks of liquid hydrogen occurs, causing boil-off losses and vent of hydrogen gas. Researches on insulation materials for liquid hydrogen are actively being conducted, but research on support design for minimal heat transfer and enhanced rigidity remains insufficient. In this study, to design support for liquid hydrogen storage tank, technique of thermal-structural coupled analysis including geometry, mesh, and boundary condition were developed using Ansys workbench, and equivalent stress and deformation distributions were analyzed.

Decarbonization plays an important role in future energy systems for establishing a zero-carbon society. Hydrogen is believed to be a promising energy source that can be converted, stored, and utilized efficiently, leading to a broad range of possibilities for future applications. Hydrogen can be stored in various forms, including compressed gas, liquid hydrogen, hydrides, adsorbed hydrogen. Among these, liquid hydrogen has high gravimetric and volumetric hydrogen densities. There are a lot of previous studies on thermal behavior of MLI and VCS and optimization insulation system, but research on the insulation performance by varying the head shape of the tank has not been conducted. In this study, thermal-structural coupled analysis was conducted on the insulation system with VCS positioned between two layers of MLI for a liquid hydrogen storage tank. The analysis considered dome shapes (torispherical, circle, ellipses), and heat flux and temperature were derived from thermal analysis to predict insulation performance. Maximum equivalent stress and deformation were calculated from the structural analysis, and the optimal dome shape was proposed.

Lifting plan in the large spacial structure is an important factor influencing the efficiency and economy of the construction process. The purpose of this study was deriving the requirements for lifting techniques as the basic research in the double spoke wheel roof structure construction. In the lift up erection method, management plan of the interference error in the column and outer-ring was needed that occur during lifting roof structure. In the bent erection method, material usage reduction plan was required by the structural design of the temporary bent. In the hybrid erection method, lifting plan was needed that minimizes weather condition and crane usage. All lifting techniques were required Value Engineering model for reduction of cost and construction period.

The objective of this research is to development of a parametric design system for membrane structures. The parametric design platform for the spatial structures has been designed and implemented. Rhino3D is used as a 3D graphic kernel and Grasshopper is introduced as a parametric modeling engine. Modeling components such as structural members, loading conditions, and support conditions are developed for structural modeling of the spatial structures. The interface module with commercial structural analysis programs is implemented. An iterative generation algorithm for design alternatives is a part of the design platform. This paper also proposes a design approach for the parametric design of Spoke Wheel membrane structures. A parametric modeling component is designed and implemented. SOFiSTik is examined to interact with the design platform as the structural analysis module. The application of the developed interface is to design optimally Spoke Wheel Shaped Ductile Membrane Structure using parametric design. It is possible to obtain objective shape by controlling the parameter using a parametric modeling designed for shape finding of spoke wheel shaped ductile membrane structure. Recently, looking at the present Construction Trends, It has increased the demand of the large spatial structure. But, It requires a lot of time for Modeling design and the Structural analysis. Finally an optimization process for membrane structures is proposed.

In this paper, time and frequency domain characteristics of Gyeong-ju earthquakes were investigated, and nonlinear time history analyses were conducted for bi-linear hysteretic structures excited by short-duration ground accelerations. Previous studies showed that larger inelastic displacements than the peak displacement of the corresponding elastic system were observed especially for the structures with structural period shorter than 0.3s, and the similar results could be obtained when long-duration ground accelerations were used as excitation loads. For the short-duration earthquakes, however, the inelastic displacements were not so large and almost identical to the peak elastic displacements.

Most of the commercial vehicle steering system is hydraulic. In this system, Breakage and leakage of oil tank is the cause of serious problems to inhibiting the vehicle direction control of the driver. In this paper, FSI(Fluid-Structure Interaction) analysis was performed considering the sloshing of oil in the tank for structural safety evaluation of the power steering oil tank. Additionally, vibration analysis of simple and fast evaluation method was performed by assuming the fluid to mass. As a result, sloshing analysis of oil in the tank was confirmed from the FSI vibration analysis, and it could get the distribution of the flow pressure 8.2kPa～-5.5kPa. Second, stress change of the FSI vibration analysis results was greater in the 33.6MPa to 0.25MPa during the transitional period 2cycle, then it showed a stable result. Third, maximum stress of FSI vibration analysis considering sloshing of the oil was 2.22MPa. maximum stress of vibration analysis assuming the fluid to mass was 4.50MPa and 103% higher than the FSI vibration analysis, but the oil tank was safely evaluate structurally safety factor 14.1. Finally, without the FSI vibration analysis by applying a weight of 0.5 to the result of vibration analysis assumes fluid to mass, it could be obtained results similar to FSI vibration analysis.

Most of the commercial vehicle steering system is hydraulic. In this system, Breakage and leakage of oil tank is the cause of serious problems to inhibiting the vehicle direction control of the driver. In this paper, FSI(Fluid-Structure Interaction) analysis was performed considering the sloshing of oil in the tank for structural safety evaluation of the power steering oil tank. Additionally, vibration analysis of simple and fast evaluation method was performed by assuming the fluid to mass. As a result, sloshing analysis of oil in the tank was confirmed from the FSI vibration analysis, and it could get the distribution of the flow pressure 8.2kPa～-5.5kPa. Second, stress change of the FSI vibration analysis results was greater in the 33.6MPa to 0.25MPa during the transitional period 2cycle, then it showed a stable result. Third, maximum stress of FSI vibration analysis considering sloshing of the oil was 2.22MPa. maximum stress of vibration analysis assuming the fluid to mass was 4.50MPa and 103% higher than the FSI vibration analysis, but the oil tank was safely evaluate structurally safety factor 14.1. Finally, without the FSI vibration analysis by applying a weight of 0.5 to the result of vibration analysis assumes fluid to mass, it could be obtained results similar to FSI vibration analysis.

LNG 선박에서 발생하는 슬로싱 충격하중은 다상유동 및 기체의 압축효과에 따라 CCS에서 발생하는 압력과 구조응답에 큰 영향을 미칠 수 있다. 본 연구에서는 슬로싱 운동 시 LNG의 유동에 의해 발생하는 슬로싱 충격을 시뮬레이션하기 위해서 다상유동을 적용한 수치해석 모델을 제시하였으며, 그 결과를 실험과 비교하여 타당성을 검토하였다. 또한 효율적인 구조응답 계산을 위해 분사모델을 이용한 유체구조 연성해석 방법에 대해서 검토하고 멤브레인형 Mark III 화물창의 강도평가에 적용하여 LNG 화물창의 강도평가를 위한 가능성을 검토하였다.

In this study, we investigated the macrobenthic community structure and spatiotemporal variations in Uljin Marine Ranching area, East Sea of Korea. Macrobenthos were collected using a modified van Veen grab sampler from April to September 2013. Total number of species sampled was 345 and mean density was 5,797 ind. m-2, both of which were dominated by the polychaetes. The most dominant species were Spiophanes bombyx (53.64%), followed by Magelona sp.1 (6.96%), Cadella semitorta (2.73%), Lumbrineris longifolia (2.16%) and Alvenius ojianus (2.08%). Cluster analysis and nMDS ordination analysis based on the Bray-Curtis similarity identified 2 station groups. The group 1 (station 2, 3, 5, 6, 8 and 9) was characterized by high abundance of the polychaetes Magelona sp.1, Lumbrineris longifolia, Scoloplos armiger, Praxillella affinis, Maldane cristata and the bivalve Alvenius ojianus, with fine sediment above 30m water depth. On the other hand, the group 2 (station 1, 4, 7 and 10) was numerically dominated by the polychaete Lumbrineriopsis sp. and the bivalve Cadella semitorta, with coarse sediment below 5m water depth. Collectively, the macrobenthic community structure showed a distinct spatial trend, which seemed to be related to the water depth and sediment composition.

As a result of an analysis of a damper system, a solution to a fire damper is developed using the continuity equation of damper control and orthogonal array. The fire damping device is made with a CAE software. Additionally, new H-120 grade fire damper is designed for the optimal offshore structure. This device will soon be tested on an actual offshore structure. An optimized fire temper is finally achieved using an orthogonal array. Using the result of present study will provide an environment friendly fire damper for offshore plants by choosing the optimum fire damper conditions

본 논문은 교량 하부에서 발생된 화재에 대한 강-콘크리트 합성구조의 전반적·국부적 손상평가를 위한 수치해석적 연구이다. 수치해석의 정확성 및 효율성을 높이기 위해 구성재료의 과도 비선형 열적·열역학적 특성이 고려된 열-구조 연성병렬 화재해석 기법이 제안되고, ANSYS solver와 연결되어 해석이 수행되며, 표준화재시험과 비교·검증된다. 검증된 해석기법을 통해 국내에서 발생된 부천고가교 합성구조에 대한 화재손상해석이 수행된다. 해석결과 강박스 거더의 하부 플랜지 및 복부의 경우 임계온도를 초과하였고 구조적 처짐과 변형 형상이 화재사고 결과와 비교적 잘 일치하였다.

현행의 내진설계의 성능목표는 인명피해를 최소화하기 위한 구조물의 붕괴방지에 있으며 기존구조물의 내진보강도 이를 만족하도록 수행되고 있다. 그러나, 최근의 해외 지진피해사례를 살펴보면 큰 지진에서도 이러한 내진성능목표는 비교적 잘 달성되었지만 엄청난 경제적 손실이 동반되어 새로운 문제점으로 제기되고 있다. 이러한 큰 경제적 손실을 줄이기 위해서는 현행 붕괴방지성능에서 벗어나 구조물의 손상을 제어할 수 있도록 손상확률에 기반하여 내진성능목표를 설정하는 새로운 내진설계개념이 필요하다. 본 연구에서는 다양한 구조적특성을 지닌 교량을 대상으로 하여 비선형지진해석을 수행하여 지진거동특성을 확인하고, 기준손상도에 대한 취약도곡선을 산정하였다. 이로부터 목표손상확률에 따른 교량구조물의 목표연성도의 특성을 분석하였다.

구조시스템은 역사적으로 발달해온 기술적 배경에 따라 건축에 사용되었고, 구조의 역할도 변화되어 왔다. 그러므로 다양한 구법으로 이루어지는 연성구조시스템의 건립사례와 시기에 따라 건립된 규모를 조사함으로써 여러 연성구조형식의 a성을 고찰하고 연성구조의 전개방향을 모색하였다. 그 결과, 연성구조시스템은 초기에 여러 케이블구조로 발달하기 시작하였으나 1970년대 이후부터는 막구조가 주로 사용되고 있는 것으로 나타났다 또한 초기의 케이블 구조시스템들은 대공간 건축에 주로 사용되었으나, 1970년 이후에는 중소규모의 건축물에 사용되는 경향이 있으며, 격자형 케이블구조나 공기막구조 그리고 돔 형식의 들림형 하이브리드 막구조가 대형공간으로 발달하는 경향을 보이는 것으로 나타났다.

반응수정계수의 핵심구성요소인 연성계수를 토질조건에 따라 제시하였다. 47개의 지진에서 얻어진 총 1,860개의 지진기록이 사용되었으며, 지반 전단파의 평균속도에 따라 4가지의 토질조건을 고려하였다. 이러한 분류는 현재 사용되고 있는 UBC(1997), NEHRP(1997) 및 IBC 200(1997)의 토질조건과 일치한다. 통계적 회귀분석으로부터, 토질조건에 따른 연성계수를 평가하기 위한 단순화된 식이 제안되었다. 제안된 식은 상대적으로 간단하면서도 평균연성계수와 잘 일치하는 결과를 보였다. 제안된 식에 근거하여, 현재의 기준과 일치하는 토질조건에 따른 연성계수를 평가할 수 있을 것으로 기대한다

연성 구조시스템은 연성재를 주 구조부재로 하여 전체 구조체계가 하중의 변화에 따라 형태가 변화할 수 있는 구조시스템이다. 이 시스템들을 힘의 전달방식을 달리하는 구조의 구성방식에 따라 분류하고, 구성방식을 파악하기 용이한 연성구조시스템의 용어를 채택하였다. 따라서 연성구조시스템은 연성선재와 연성면재의 구성에 따라 분류되었는데, 연성선재구조물에 일방향케이블구조, 격자형 케이블구조, 방사형 케이블구조, 연성면재의 구조물에 공기막구조 현수막구조, 선재와 면재의 하이브리드 구조물에 달림형하이브리드 막구조, 들림형 하이브리드 막구조로 분류체계와 용어를 결정하였다.

반응수정계수의 핵심구성요소인 연성계수에 대하여 통계적 분석을 수행하였다. 연성계수의 체계적인 산정을 위하여 총 1,860개의 지진기록을 수집하였다. 수집된 지진기록을 지반 전단파의 평균속도에 따라 4가지로 분류하고, 탄소성 이력거동을 가지는 단자유도 구조물에 대하여 비탄성 스펙트럼을 작성하였다. 작성된 비탄성 스펙트럼으로부터 연성계수를 구하고, 변위연성비, 토질조건, 규모 및 진앙거리가 연성계수에 미지는 영향을 분석하였다. 토질 조건별로 평균연성계수를 구하고, 산정된 연성계수의 산포도를 검토하기 위하여 변동계수를 산정하였다.