In the case of a school building, even though it is a regular structure in terms of plan shape, if the masonry infill wall acts as a lateral load resisting element, it can be determined as a torsionally irregular building. As a result, the strength and ductility of the structure are reduced, which may cause additional earthquake damage to the structure. Therefore, in this study, a structure similar to a school building with torsional irregularity was selected as an example structure and the damping performance of the PC-BRB was analyzed by adjusting the eccentricity according to the amount of masonry infilled wall. As a result of nonlinear dynamic analysis after seismic reinforcement, the torsional irregularity of each floor was reduced compared to before reinforcement, and the beams and column members of the collapse level satisfied the performance level due to the reduction of shear force and the reinforcement of stiffness. The energy dissipation of PC-BRB was similar in the REC-10 ~ REC-20 analytical models with an eccentricity of 20% or less. REC-25 with an eccentricity of 25% was the largest, and it is judged that it is effective to combine and apply PC-BRB when it has an eccentricity of 25% or more to control the torsional behavior.

In this study, a study on the design of the rake shape of a rotary screener is conducted. The rake bar and rake of a rotary screener were designed, and three types for the rake shape were designed by changing the rake shape. Structural analysis was conducted in consideration of the vertical load applied when the narrow object was pulled up by the rake and the friction force applied underwater, and the more efficient type was verified by comparing the stress and strain applied to the lake by shape. In addition, structural analysis was additionally performed by changing the material of the rake to a carbon composite material in the same manner. That is, in order to improve the need to replace the entire rake part in case of damage, we will examine the improvement of the strength of the rake by performing structural analysis by changing the material of the rake.

The automatic dust separator is a device installed in the suction tank of the pumping or drainage plant, and prevents foreign substances such as aquatic plants or wood chips from being sucked into the underwater pump. Since the dust separator obstructs the flow of water for separating dusts, a water level difference is likely to occur before and after the dust separator. Since the water level difference before and after the dust separator acts as an additional hydraulic load on the dust separator structure, it may reduce the lifetime of the dust separator and cause damage. In this study, in order to reduce the water level difference, we devised changing the existing I-beam-shaped dust separator parts to a streamlined shape, and quantitatively analyzed the water level difference before and after the dust separator, hydraulic load, and flow velocity distribution through computational fluid analysis to confirm the effect of design improvement.

Domestic dust remover began to be manufactured and installed in the late 1980s by introducing Japanese products and technologies. Currently, the design standards of dust remover are applied to Japan's design standards and partly sub-unit technology was developed for the domestic environment, but no technology was not developed. In addition, most of the manufacturers are small or small, so many of them have been installed and operated for 25 years because they develop small technologies such as parts deformation and functional addition rather than core technology development. Mechanical dust remover require about 70% of manufacturing costs compared to conventional hydraulic dust remover, which can reduce initial production costs, reduce maintenance costs due to low failure rates, and can be operated reliably. Existing hydraulic dust remover had a problem of contaminating rivers due to leakage of hydraulic oil, but mechanical dust remover have no factors that cause water pollution. Therefore, this study developed a rack-type operating structure for optimal and new construction by developing a multi-stage rack structure of mechanical decontamination components, which are substitutes of conventional rotary and hydraulic dust remover.

In this study, we verify the stability of the operation of mechanical dust remover by conducting the development of a rack-type operating structure and mechanism. This led to the development of a new type of mechanical dust remover, which resulted in the following conclusions. The optimum design was established for the specifications and shapes of the main structural and power transfer components according to the required capabilities of the mechanical dust remover. The power transmission structure of the worm gear and the spur gear corresponding to the rack bar gear box was determined to fit the lift structure, which is a combination of rack sprockets. When the rack bar is elongated, it develops a rack-type operating structure that enables smooth descent by allowing it to form a gap between the rake and the screen. And the mechanism was verified by calculating the stresses on the sprocket entering the rack box.

구조물의 진동에 의해 유발되는 사용성, 안정성 저하를 방지하고, 성능을 개선하기 위하여 많은 진동제어시스템이 사용되어 왔다. 제어기 설계가 H2-norm, H∞-norm 으로 분리되어 독립적으로 이루어지다가 LMI 기법에 의하여 보다 효율적인 제어기 설계가 가능하게 되었다. 본 연구에서는 관심지점의 구조물 응답을 특정한 값 이하로 보장한 상태에서 제진장치 구동에 필요한 변수를 최소 화하는 제어알고리듬을 개발하여 능동형뿐만 아니라 수동형제진장치에도 적용하는 방안을 제시하였다. 관심지점의 구조물 응답의 제한은 요구 등가감쇠비와 H∞-norm을 연계하여 구속조건으로 설정하고 목적함수는 제진장치의 이송거리 또는 댐퍼 용량은 H2-norm으 로 표현하는 혼합제어를 구성하였다. 본 연구에서 제안된 혼합제어 기법을 능동질량감쇠기와 등가치환 점탄성 댐퍼가 설치된 구조물에 적용하여 수치적으로 검증하였다. 수치해석결과, 혼합제어문제를 LMI표준형으로 전환하면 능동형, 수동형 제진장치 설계를 보다 용이하게 적용 가능함을 알 수 있었다.

This study investigates the effect of fatigue stress on the damping capacity in a damaged Fe-22Mn-12Cr-3Ni-2Si- 4Co damping alloy under fatigue stress. α’ and ε-martensite forms by fatigue stress in the damaged Fe-22Mn-12Cr-3Ni-2Si- 4Co damping alloy under fatigue stress. The α’ and ε-martensite forms with the specific direction and surface relief, or they cross each other. With an increasing fatigue stress, the volume fraction of α’-martensite and ε-martensite increases. With an increasing fatigue stress, the damping capacity increases with an increase in the volume fraction of ε-martensite. The increase in the damping capacity in the damaged Fe-22Mn-12Cr-3Ni-2Si-4Co alloy under fatigue stress strongly affects the increase of ε-martensite formed by fatigue stress, but the damping capacity of the damaged Fe-22Mn-12Cr-3Ni-2Si-4Co damping alloy under fatigue stress is strongly controlled by a large amount of α’-martensite.

This study was carried out to investigate the effect of grain size on the damping capacity of the Fe-26Mn-4Co-2Al damping alloy. α’ and ε-martensite were formed by cold working, and these martensites were formed with a specific direction and surface relief. With an increase in grain size, the volume fraction of α’ and ε-martensite increased by decrement the austenite phase stability. This volume fraction more rapidly increased in cold-rolled specimen than in the specimen that was not cold-rolled. The damping capacity also increased more with the augmentation an increased grain size and more rapidly increased in cold-rolled specimen than in the specimen that was not cold rolled. The effect of grain size on the damping capacity was larger in the cold-rolled specimen than the specimen that was not cold-rolled. Damping capacity linearly increased with an increase in volume fraction of ε-martensite. Thus, the damping capacity was affected by the ε-martensite.

본 연구에서는 마찰력에 따른 TMD의 작동-정지조건과 각 조건에 따른 운동방정식을 정리하고, TMD의 마찰계수가 풍진동 제어성능에 미치는 영향을 수치해석을 통하여 확인하였다. 일반적인 하중과 달리 풍하중은 크기와 방향의 변화가 크기 때문에 TMD 는 마찰력에 의하여 작동-정지상태를 반복하게 되므로, TMD의 마찰계수를 주요 변수로 설정하였다. 또한 외부하중의 크기, 구조물의 진동수, TMD의 질량비도 매개변수로 설정하여 TMD의 제진성능에 대한 영향을 파악하고자 하였다. 자유진동, 조화강제진동, 풍진동에 대한 수치해석의 결과, 외부하중의 크기가 작고, 구조물의 진동수가 낮을수록 마찰계수에 의한 TMD의 제진성능의 손실이 커질 수 있음을 확인하였으며, 초고층 건물에 대한 TMD 설계시 마찰계수의 영향을 반드시 고려하여야 할 것으로 판단된다.

구조물의 성능을 개선하기 위하여 다양한 진동제어장치가 사용되고 있다. 대부분의 제진장치는 구조물의 감쇠비를 증가시킴으로써 성능개선효과를 유도하기 때문에 증가된 감쇠비는 제진장치에 의한 구조물의 성능을 평가하는 중요한 지표가 될 수 있다. 본 연구에서는 강풍 등으로 제진장치가 운영 중인 상태에서 구조물의 응답만을 이용하여 각 모드에 증가된 등가감쇠비를 추정하는 프로세스를 개발하고 이를 성능개선효과를 평가하는데 활용하고자한다. 제진장치가 설치된 구조물은 비고전 감쇠시스템이므로 상태공간 모드분해법을 이용하여 계측응답으로부터 모드 응답을 구하고, 분해된 모드응답에 가상 동적 진동기를 적용하여 각 모드에 증가된 감 쇠비를 구하였다. 제안된 제진장치 설치 구조물 감쇠비 추정법을 검증하기 위하여 수동형 제진장치로 카고메 점탄성 댐퍼를, 능동형 제진장치로 능동질량감쇠기를 구조물에 적용하여 각 제진장치에 의한 감쇠비를 추정한 결과 매우 정교하게 예측 가능함을 알 수 있었다.

The proposed hybrid damper installs at a coupling beam and consists of a high-damping rubber (HDR) and steel pin. The proposed hybrid damper adopted a pin-lock system acts as a viscoelastic damper under wind load (small displacement) while it behaves as a hysteretic damper under earthquake load (large displacement). In this paper, the pin-lock mechanism and structural performance of the proposed hybrid damper is evaluated through experiment. Experiments were carried out with the variables which displacement, loading frequency and steel pin quantities were used. Test results showed that the pin-lock mechanism and the performance of the hybrid damper under a large displacement were verified. Also equivalent damping ratios of HDR were increasing at a small displacement as displacement amplitudes were increasing. However HDR did not depend on frequency,

In this study, shaking table test has been carried out for the dual frame passive control system for seismic performance verification of the proposed system. The proposed system was separated into two independent frameworks that are strength resistant core and frame structure by connecting to the damper. Moreover, the seismic performance improvement of the proposed system has been verified by comparing and analyzing the experimental results of the proposed system with an existing core system. As a result of the shaking table test, acceleration and displacement responses of dual-frame vibration control system are decreased than those of the existing strength resistant type core system. In the case of the core system, while the damage was concentrated on the column of first floor, the damage of the dual system was dispersed in each layer. The damage also was concentrated on the damper, almost no damage occurs to the structural members. It has been emphasized that installed dampers in the proposed dual system reduce the input energy of whole structure by absorbing seismic input energy, which leads overall system damage to be reduced.

The performance enhancement of various structural building systems from natural hazards has become an inctreasingly important issue in engineering field. In this paper, visco-elastic(VE) CST30 damping systems were tested under cyclic loadings to evaluate their performance in terms of ductility and energy dissipation. Main test variables are relative shear stiffness, rate of loading frequency, and thickness of specimens to evaluate the seismic capacity based on the performance criteria. This experiment was performed using a total of 12 specimens, subjected to cyclic loadings up to a shear deformation of 500%. All the CST30 dampers provided a ductile and stable hysterestic behavior when subjected to the demands of large shear stiffness and different loading frequencies. The test results showed that the CST30 dampers are an effective damping systems to enhance the buildings performance for remodeling and retrofit of buildings

본 연구에서는 초고층 건물의 풍동실험에서 얻어진 풍하중에 대하여 모드에 기초한 풍응답 해석을 수행하여 사용성을 검토하고, 목표 응답수준을 획득할 수 있는 수동 및 능동 질량형 장치의 예비설계까지 수행 가능한 프로그램을 개발하였다. 본 연구에서 개발된 프로그램을 실제 초고층 건물의 풍동실험결과에 적용하여 TMD와 AMD의 설계를 수행하였으며, 가속도 응답과 질량체 이송거리를 중심으로 결과를 비교분석하였다. TMD와 AMD 모두 요구되는 응답 수준을 만족하는 최소의 질량체를 사용하는 경우 질량체 이송거리가 증가하는 문제점이 발생하였다. 특히 AMD는 TMD 보다 적은 질량체로도 사용성 기준을 만족하는 응답수준을 획득할 수 있다는 장점이 있었으나, 질량체의 이송거리가 지나치게 커지는 문제점이 있으며, 고주파통과필터와 같은 부가적인 이송거리 저감대책이 요구된다.

Friction energy dissipative devices have been increasingly implemented as structural seismic damage protecting systems due to their excellent seismic energy dissipating capacity and high stiffness. This study develops rotational friction energy dissipative devices and verifies experimentally their cyclic response. Based on the understanding of the differences between the traditional linear-motion friction behavior and the rotational friction behavior, the configuration of the frictional surface was determined by investigating the characteristics of the micro-friction behavior. The friction surface suggested in this paper consists of brake-lining pads and stainless steel sheets and is normally stressed by high-strength bolts. Based upon these frictional characteristics of the selected interface, the rotational friction energy dissipative devices were developed. Bolt torque-bearing force tests, rotational friction tests of the suggested friction interfaces were carried out to identify their frictional behavior. Test results show that the bearing force is almost linearly proportional to the applied bolt torque and presents stable cyclic response regardless of the experimental parameters selected this testing program. Finally, cyclic tests of the rotational friction energy dissipative devices were performed to find out their structural characteristics and to confirm their stable cyclic response. The developed friction energy dissipative devices present very stable cyclic response and meet the requirements for displacement-dependent energy dissipative devices prescribed in ASCE/SEI 7-10.

본 논문에서는 구조물과 능동형 제진장치를 상용 구조해석 프로그램상에서 해석하는데 필요한 등가모델을 제시하였으 며, 이를 통해 부재수준의 구조검토가 가능하도록 하기 위한 연구를 진행하였다. 능동형 제진장치를 일반적인 구조해석모 델에 반영하기 위하여 가상의 스프링과 대쉬폿을 이용한 등가링크 모델과, 별도의 축소모델 해석결과를 바탕으로 산정된 제어력을 제진장치 설치위치에 하중으로 작용시키는 등가하중 모델을 제시하였다. 수직캔틸레버 모델과 주상복합 건물 모 델을 대상으로 능동형 제어기 설계를 위해 모드에 기초한 축소모델을 구축하고, 이를 토대로 산정된 제어이득으로부터 등 가모델을 도출하였다. 이들 모델에 대해 얻어진 가속도 및 변위의 RMS 응답과 최대 부재력을 토대로 등가해석모델의 유 효성을 검증하였다. 결과적으로 능동형 제진장치의 상용 구조해석 프로그램을 통해 제어대상 구조물의 부재력 수준까지 상 세한 구조검토가 가능함을 확인하였으며, 상대적으로 등가링크 모델이 더 우수한 정확도를 나타내었다.

근래에 들어와서 3T (Twisted, Tapered, Tilted)로 대별되는 비정형 초고층 건축물이 다수 계획되고 있다. 이러한 비정형 초고층 건물을 위해서 구조적인 효율성 및 조형성 때문에 다이어그리드 구조시스템이 현재까지 가장 널리 사용되고 있는 구조시스템 중의 하나이다. 건축적인 조형미 등의 이유로 경사진 비정형 초고층 건물에 대한 계획안이 다수 발표되고 있으며 다수의 구조물들이 다이어그리드 구조시스템을 활용하고 있다. 경사진 비정형 초고층 건물은 횡하중뿐만 아니라 자중에 의해서도 횡방향 변위가 발생한다. 따라서 정형적인 초고층 건물보다 횡방향 응답을 저감시카는 젓이 더 중요한 문제로 대두된다. 본 연구에서는 경사진 다이어그리드 비정형 초고층 건물의 지진응답을 저감시키기 위하여 스마트 TMD를 적용하였고 그 제어성능을 평가하였다. 스마트 TMD를 구성하기 위하여 MR 감쇠기를 사용하였으며 스마트 TMD는 그라운드훅 제어알고리즘을 사용하여 제어하였다. 100 층의 예제구조물에 대하여 제어를 하지 않은 경우와, 일반적인 TMD를 사용한 경우, 그리고 스마트 TMD를 사용하여 제어한 경우를 비교 검토하였다. 수지해석결과 스마트 TMD가 변위 응답 제어에는 우수한 성능을 나타냈지만 가속도응답제어에는 효과적이지 못했다.

본 논문에서는 철근콘크리트 구조물과 같이 강성저감으로 인해 낮은 에너지 소산능력을 갖는 구조물의 제진성능을 비선형시간이력해석을 통해 조사하였다. 원구조물은 modified Takeda 이력모델을 갖는 단자유도시스템으로 이상화하였고, 완전탄소성 모델로 이력감쇠장치를 모델링하였다. 수치해석결과의 통계를 기초로 등가선형화에 의한 제진응답 평가의 적용성을 검증하였고, 제진보강 구조물의 응답예측을 위한 경험식을 제시하였다. 결과적으로 등가선형화를 통한 변위응답 평가보다는 본 연구에서 제시한 경험식을 이용하여 요구연성도를 추정하는 것이 더 정확하다. 경험식에서 얻어진 적정 감쇠기 항복강도는 완전탄소성시스템에 대한 최적 항복강도와는 상당한 차이를 가진다. 획득 가능한 연성도 저감효과는 원구조물의 고유주기가 짧을수록, 지진의 상대적 강도가 약할수록 우수한 것으로 나타났다.