PURPOSES : The wedge-type anchorage system requires a complex analysis of not only the tensile stress of the CFRP plate, but also the compressive stress and shear stress generated by the wedge action. The purpose of this study is to find a composite material failure theory that is suitable for analyzing the behavior of wedge-type anchorage system among various failure theories. METHODS : In this study, numerical analysis of various composite material failure theories was performed to analyze the anchorage strength and failure mode of the wedge-type anchorage system according to each failure theory, and compared with actual test results to determine the composite material failure theory most suitable for analyzing the behavior of a wedge-type anchorage system. RESULTS : Since the Maximum Stress failure theory shows similar results to the actual test in terms of failure mode and anchorage strength, there is no significant problem in applying it to the wedge-type anchorage system. However, it is judged to be difficult to apply under property conditions where interactions between stresses are highlighted. The Tsai-Hill and Tsai-Wu failure theories are considered unsuitable for application to wedge-type anchorage systems because the wedge angle conditions at which the most advantageous anchorage strength occurs are significantly different from other theories and the fracture type cannot be predicted. The Hashin-Rotem failure theory is considered to be the most appropriate to apply as a failure theory for the wedge-shaped anchorage system because the anchorage strength was slightly lower than the actual test results, but there was no significant difference, and the failure mode was consistent with the test results. The Hashin failure theory is judged to be unsuitable for application as a failure theory for the wedge-type anchorage system because the anchorage strength and failure mode were interpreted differently from the actual test results. CONCLUSIONS : The Hashin-Rotem failure theory was presented as the composite material failure theory most suitable for analyzing the behavior of wedge-type anchorage system.

Three kinds of STS304-Zr alloys were fabricated by varying the Zr content, and their microstructure and fracture properties were analyzed. Moreover, we performed heat treatment to improve their properties and studied their microstructure and fracture properties. The microstructure of the STS304-Zr alloys before and after the heat treatment process consisted of α-Fe and intermetallics: Zr(Cr, Ni, Fe)2 and Zr6Fe23. The volume fraction of the intermetallics increased with an increasing Zr content. The 11Zr specimen exhibited the lowest hardness and fine dimples and cleavage facets in a fractured surface. The 15Zr specimen had high hardness and fine cleavage facets. The 19Zr specimen had the highest hardness and large cleavage facets. After the heat treatment process, the intermetallics were spheroidized and their volume fraction increased. In addition, the specimens after the heat treatment process, the Laves phase (Zr(Cr, Ni, Fe) 2) decreased, the Zr6Fe23 phase increased and the Ni concentration in the intermetallics decreased. The hardness of all the specimens after the heat treatment process decreased because of the dislocations and residual stresses in α-Fe, and the fine lamellar shaped eutectic microstructures changed into large α-Fe and spheroidized intermetallics. The cleavage facet size increased because of the decomposition of the fine lamellarshaped eutectic microstructures and the increase in spheroidized intermetallics.

PURPOSES : This paper presents a comparison study between dynamic and static analyses of falling weight deflectometer (FWD) testing, which is a test used for evaluating layered material stiffness. METHODS: In this study, a forward model, based on nonlinear subgrade models, was developed via finite element analysis using ABAQUS. The subgrade material coefficients from granular and fine-grained soils were used to represent strong and weak subgrade stiffnesses, respectively. Furthermore, the nonlinearity in the analysis of multi-load FWD deflection measured from intact PCC slab was investigated using the deflection data obtained in this study. This pavement has a 14-inch-thick PCC slab over finegrained soil. RESULTS: From case studies related to the nonlinearity of FWD analysis measured from intact PCC slab, a nonlinear subgrade modelbased comparison study between the static and dynamic analyses of nondestructive FWD tests was shown to be effectively performed; this was achieved by investigating the primary difference in pavement responses between the static and dynamic analyses as based on the nonlinearity of soil model as well as the multi-load FWD deflection. CONCLUSIONS : In conclusion, a comparison between dynamic and static FEM analyses was conducted, as based on the FEM analysis performed on various pavement structures, in order to investigate the significance of the differences in pavement responses between the static and dynamic analyses.

At modern mechanical and automotive industry, the material with light weight proceeds in order to thr environmental issue and high performance. Machine part is fastened with numbers of bolts and nuts. Generally, the metal part at mechanical structure is fastened with bolt and nut through puncturing. But it is difficult to puncture at CFRP with the property of fiber structure like the general metal. In this study, the fracture behavior is investigated by the hole and crack at the plate of the unidirectional CFRP due to ply angle. The thickness of plate is 2 mm. Two laminates with the varied ply angles are layered and eight plies are made. The hole is placed at the center of plate and the cracks with the length of 2 mm are generated on both left and right sides from the hole. The finite element program of ANSYS is carried out in order to analyze the CFRP with fiber layer. As analysis, the maximum reaction force and equivalent stress are investigated due the angle of ply. The reaction force in case of the stacking angle of 90° is shown to be greatest among all specimens.

Columns in existing reinforced concrete structures that are designed and constructed without considering seismic loads generally exhibit widely spaced transverse reinforcements without using seismic hooks. Due to the insufficient reinforcement details in columns compared to the reinforcement requirements specified in modern seismic codes, brittle shear failure is likely to occur. This may lead to sudden collapse of entire structure during earthquakes. Adequate retrofit strategy is required for these columns to avoid such catastrophic event. In order to do so, behavior of columns in existing reinforced concrete structures should be accurately predicted through computational analysis. In this study, an analytical model is proposed for accurately simulating the cyclic behavior of shear critical columns. The parameters for backbone, as well as pinching and cyclic deterioration in strength and stiffness are calibrated using test data of column specimens failed by shear.

Purpose of this study is to investigate structural behavior of the rectangular hollow column with various transverse reinforcement details. Experimental variables are diameter, arrangement details and lateral spacing of cross tie. A total of 66 column specimens have been prepared and tested under axial compressive load. Test results showed that behaviors of column specimens were different depending on the cross tie details. Specimens with cross tie wrapping longitudinal steel and transverse steel have greater strength and ductility than specimens with cross tie wrapping the longitudinal steel.

In order to provide the basis data for broad use and safe design of carbon fiber reinforced plastic, this paper aims at investigating the fracture behavior on CFRP specimen composed of one directional fiber through three point bending test. On the basis of experimental result, the improvement of composite layer specimen can be secured with the other data to compare the existing specimen. The fracture behavior happened at the experimental procedure is investigated in this study. The maximum loads of 1200 N, 1700N and 1600N are shown respectively at the specimens with the layer angles of 30°, 45° and 60°. The highest load is shown at the layer angle of 60° among all specimens and the longest displacement is maintained until each of the layer structure is broken down. The fracture due to the force applied from the outside can be prevented by applying the result of this study to the real structure. As structural safety can be evaluated and anticipated through this study, it is thought that the safe design is devoted.

As CFRP with only a single material shows the various fracture properties, it has been applied to the many areas through the whole industry. The method bonding with adhesive has been recommended to apply the CFRP to structure. But it is inevitable that the mechanical joints with bolt, nut and rivet have been used sometimes. This study investigates the effect that these joints influence the CFRP panel through the analysis result. The analysis models as CFRP panels with the thickness of 5 mm have four kinds of layer angles which are 30°, 45°, 60° and 75°. The fracture property is examined when the pressure by the mechanical joint is applied to the upper panel. As the joint pressure is distributed most effectively in case of the layer angle of 60°, it is shown that this pressure becomes lower and the deformation of panel becomes lowest. On the basis of this study result, it is thought that the foundation data for the design of CFRP structure can be provided and contributed to the safety design of structure.

This study aims at analyzing the property of the structural body bonded with alumimum foam by the utilization of the aluminum foam of closed type used generally with impact absorbent. The structural bodies bonded with the aluminum foam of DCB and TDCB are designed in this study, and then the fatigue analysis and experiment are carried out. At fatigue analysis, the maximum load happens at all of each specimen models when the fatigue life of 0 to 50 cycle is proceeded. And from the point of time that the maximum load happens, the load at the bonded surface is seen to be decreased in cases of analysis and experiment. As the specimen thickness is increased, the maximum load happened at specimen is increased. It is confirmed that the result of fatigue analysis becomes similar to that of fatigue experiment for verification. It is thought that the study data on various specimen thicknesses can be secured simply without the extra fatigue experimental procedure. By using this study result, the mechanical properties of the structural bodies bonded with the alumimum foams of DCB and TDCB with mode Ⅲ type can be thought to be analyzed effectively.

Because aluminum foam is porous material, the frature property is different from that of non-porous material. This aluminum foam can be used with the joint bonded with adhesive in order to utilize the light weight to the maximum. So, the study of fracture property on bonded surface can be important. In this study, the analyses on the specimens with two kinds of configuration as DCB(Double Cantilever Beams) and TDCB(Tapered Double Cantilever Beams) aluminum foams of mode Ⅲ type bonded with adhesive are carried out and compared with each other. And the fracture properties the adhesive surfaces of the structure with bonded aluminum foams are studied as the static experiments on these verifications are done. DCB and TDCB specimens used in this study have the variable of thickness(t) as 35mm, 45mm and 55mm. As the result of this study, the range of reaction forces are 0.3 to 0.8 kN and 0.5 to 1.2 kN at DCB and TDCB specimens respectively. The results of the static experiments can also be confirmed with these similar results. These study results can be obtained by only a simulation without the special experimental procedures. The mechanical properties of the bonded structures composed of DCB and TDCB aluminum foams with mode Ⅲ type can be thought to be analyzed effectively.

The present study is undertaken to evaluate the effect of volume fraction on the results of Charpy impact test for the rubber matrix filled with nano sized silica particles composites. The Charpy impact tests are conducted in the temperature range 0°C and –10°C. The range of volume fraction of silica particles tested are between 11% to 25%. The critical energy release rate GIC of the rubber matrix composites filled with nano sized silica particles is affected by silica volume fraction and it is shown that the value of GIC decreases as volume fraction increases. In regions close to the initial crack tip, fracture processes such as matrix deformation, silica particle debonding and delamination, and/or pull out between particles and matrix which is ascertained by SEM photographs of Charpy impact fracture surfaces.

An aluminum foam is the super light metal which can be adjusted with the adhesive by using the joint method. In this study, the tapered double cantilever beams(TDCB) with the type of mode Ⅲ are manufactured with aluminum foam. The fracture toughness at the joint of the structure bonded with only a adhesive can be obtained. The static analyses are carried out and verified the results by the experiment. As the results of static analyses, the reaction forces ranged from 0.30 to 0.41 kN at all specimens are shown when the forced displacements are proceeded as much as 8 to 9 mm. The tapered double cantilever specimen for mode Ⅲ with the thickness of 55 mm is carried out by the static experiment representatively to verify the analysis results. As the results of analyses and experiments are compared with each other, there is a little bit of difference between these results. So, the simulation results of this study can be thought to be confirmed. It is thought that even the only analysis data omitting the extra experimental procedure can be verified in order to use the data practically. Through the result of this study, the mechanical properties at TDCB specimens with the type of mode Ⅲ can be understood.

PURPOSES : In this study, a fracture-based finite element (FE) model is proposed to evaluate the fracture behavior of fiber-reinforced asphalt (FRA) concrete under various interface conditions. METHODS: A fracture-based FE model was developed to simulate a double-edge notched tension (DENT) test. A cohesive zone model (CZM) and linear viscoelastic model were implemented to model the fracture behavior and viscous behavior of the FRA concrete, respectively. Three models were developed to characterize the behavior of interfacial bonding between the fiber reinforcement and surrounding materials. In the first model, the fracture property of the asphalt concrete was modified to study the effect of fiber reinforcement. In the second model, spring elements were used to simulated the fiber reinforcement. In the third method, bar and spring elements, based on a nonlinear bond-slip model, were used to simulate the fiber reinforcement and interfacial bonding conditions. The performance of the FRA in resisting crack development under various interfacial conditions was evaluated. RESULTS : The elastic modulus of the fibers was not sensitive to the behavior of the FRA in the DENT test before crack initiation. After crack development, the fracture resistance of the FRA was found to have enhanced considerably as the elastic modulus of the fibers increased from 450 MPa to 900 MPa. When the adhesion between the fibers and asphalt concrete was sufficiently high, the fiber reinforcement was effective. It means that the interfacial bonding conditions affect the fracture resistance of the FRA significantly. CONCLUSIONS: The bar/spring element models were more effective in representing the local behavior of the fibers and interfacial bonding than the fracture energy approach. The reinforcement effect is more significant after crack initiation, as the fibers can be pulled out sufficiently. Both the elastic modulus of the fiber reinforcement and the interfacial bonding were significant in controlling crack development in the FRA.

A progressive failure analysis procedure for composite laminates is completed in here. An anisotropic plastic constitutive model for fiber-reinforced composite material is implemented into computer program for a predictive analysis procedure of composite laminates. Also, in order to describe material behavior beyond the initial yield, the anisotropic work-hardening model and subsequent yield surface are implemented into a computer code, which is Predictive Analysis for Composite Structures (PACS). The accuracy and efficiency of the anisotropic plastic constitutive model and the computer program PACS are verified by solving a number of various fiber-reinforced composite laminates with and without geometric discontinuity. The comparisons of the numerical results to the experimental and other numerical results available in the literature indicate the validity and efficiency of the developed model.

A progressive failure analysis procedure for composite laminates is developed in here and in the companion paper. An anisotropic plastic constitutive model for fiber-reinforced composite material, is developed, which is simple and efficient to be implemented into computer program for a predictive analysis procedure of composites. In current development of the constitutive model, an incremental elastic-plastic constitutive model is adopted to represent progressively the nonlinear material behavior of composite materials until a material failure is predicted. An anisotropic initial yield criterion is established that includes the effects of different yield strengths in each material direction, and between tension and compression. Anisotropic work-hardening model and subsequent yield surface are developed to describe material behavior beyond the initial yield under the general loading condition. The current model is implemented into a computer code, which is Predictive Analysis for Composite Structures (PACS), and is presented in the companion paper. The accuracy and efficiency of the anisotropic plastic constitutive model are verified by solving a number of various fiber-reinforced composite laminates with and without geometric discontinuity. The comparisons of the numerical results to the experimental and other numerical results available in the literature indicate the validity and efficiency of the developed model.

In this study, carbon/epoxy composite DCB(double cantilever beam) specimens based on K-means clustering and wavelet transform analyses are presented. For the fracture Mode I, the fiber orientation θ = [0 ]24 and θ = [±45]12 both shown up stable crack growth in DCB testing. For the fiber orientation θ = [0 ]24 , the continuous type AE signal showed at central frequency 130～270kHz, which means that matrix micro cracking was occurred. The Burst type AE signal was occurred at central frequency 200～300kHz due to fiber bridging and fiber breaking. Other burst type AE signals were occurred at central frequency 130～180kHz with very high amplitude due to fiber bridging. For the fiber orientation θ = [±45]12 , the burst type signal showed at central frequency 220～300kHz, which means that fiber breaking was occurred. Mixed type of burst and continuous signals were captured at central frequency 250～480kHz due to fiber friction.

Aluminum foam as porous material in wide use has the excellent mechanical and thermal properties. As adhesive process technique is used by bonding such composites as aluminum foam, fracture toughness at adhesive joint is the main point to investigate. In this study, DCB specimens are manufactured to evaluate the strengths at adhesive joints on the basis of British industrial and ISO international standards. Four kinds of specimens are made by changing the height of the specimen and these experimental results are compared with each other. Energy release rates are also calculated at mode I. As the hight of specimen becomes higher, reaction force and energy release rates become higher. Through the correlation obtained by this study result, aluminum foam material bonded with adhesive can be applied to the real composite structure and mechanical property and fracture toughness are analyzed systematically.

The fiber reinforced polymer (FRP) strengthening is significantly effective for enhancing the performances of concrete to the high strain rate loadings. However, the FRP retrofitted concrete members show different behaviors comparing to quasi-static cases. This study presents experimental observation on behaviors of meso-scale concrete members retrofitted with FRP sheets under low-velocity drop-weight impact loadings. Concrete specimens with the dimensions of 100×100×400 mm were fabricated and various FRP sheets were attached. The specimens with a reinforced bottom surface and the doubly reinforced specimens showed much higher energy absorptions. Also, reinforced concrete (RC) members were cast and reinforced with CFRP sheets. The FRP flexural and shear strengthening RC beams has weakness in the spalling failure because the impact load concentrated the concrete face which is not strengthened with FRP sheets.

The present study was undertaken to evaluate the effect of temperature on the results of Charpy impact test for glass fiber reinforced polyurethane(GF/PUR) composites. The Charpy impact test were conducted in the temperature range from -50˚ to 50˚. The impact fracture toughness of GF/PUR composites was considerably affected by temperature and it was shown that the maximum value was appeared at room temperature. It is believed that sensitivity of notch on impact fracture energy were increased with decrease in temperature of specimen. As the GF/PUR composites exposed in low temperature, impact fracture toughness of composites decreased gradually owing to the decrease of interface bonding strength caused by difference of thermal expansion coefficient between the glass fiber/polyurethane resin. And decrease of interface bonding strength of composites with decrease in specimen temperature was ascertained by SEM photographs of Charpy impact fracture surface.