This study investigates the effect of fatigue stress on the damping capacity in a damaged Fe-22Mn-12Cr-3Ni-2Si- 4Co damping alloy under fatigue stress. α’ and ε-martensite forms by fatigue stress in the damaged Fe-22Mn-12Cr-3Ni-2Si- 4Co damping alloy under fatigue stress. The α’ and ε-martensite forms with the specific direction and surface relief, or they cross each other. With an increasing fatigue stress, the volume fraction of α’-martensite and ε-martensite increases. With an increasing fatigue stress, the damping capacity increases with an increase in the volume fraction of ε-martensite. The increase in the damping capacity in the damaged Fe-22Mn-12Cr-3Ni-2Si-4Co alloy under fatigue stress strongly affects the increase of ε-martensite formed by fatigue stress, but the damping capacity of the damaged Fe-22Mn-12Cr-3Ni-2Si-4Co damping alloy under fatigue stress is strongly controlled by a large amount of α’-martensite.

Fatigue crack growth retardation of 304 L stainless steel is studied using a neutron diffraction method. Three orthogonal strain components(crack growth, crack opening, and through-thickness direction) are measured in the vicinity of the crack tip along the crack propagation direction. The residual strain profiles (1) at the mid-thickness and (2) at the 1.5 mm away from the mid-thickness of the compact tension(CT) specimen are compared. Residual lattice strains at the 1.5 mm location are slightly higher than at the mid-thickness. The CT specimen is deformed in situ under applied loads, thereby providing evolution of the internal stress fields around the crack tip. A tensile overload results in an increased magnitude of the compressive residual stress field. In the crack growth retardation, it is found that the stresses are dispersed in the crack-wake region, where the highest compressive residual stresses are measured. Our neutron diffraction mapping results reveal that the dominant mechanism is by interrupting the transfer of stress concentration at the crack tip.

본 논문에서는 페이즈필드 설계법 기반의 피로 제약 조건 구조물의 위상최적설계를 수행하였다. 페이즈필드 설계법의 도입으로 기존의 위상최적설계법에서 발생하기 쉬운 중간 영역의 크기를 크게 감소시켰다. 수정된 upper bound P-norm의 도입으로 모든 지점의 응력 성분을 고려하면서, 전역적 응력값이 국부적 최대 응력값과 근사한 값을 가질 수 있도록 설정하였다. 또한 기존의 피로 파괴 제약 조건 위상최적설계에서 다루지 않았던 응력 수정 계수에 대한 고려를 위하여 위상최적설계 결과물의 1차 주응력 성분을 고려하여 응력 수정 계수를 도입하고 이에 따라 허용 응력 진폭 값을 수정 하였다. 이를 통하여 인장 응력으로 인한 내구 한도 감소 요인을 반영한 체계적인 설계 방안을 제시하였다.

The residual stress analysis and fatigue test of a steel plate with a hole were performed in order to investigate the effects of the cold expansion on the fatigue life of the plate. The cold expansion method is a metal forming process by expanding a hole in order to induce compressive tangential residual stresses near the hole. In this research, a S45C steel plate of 3.2 mm thickness with a hole of 4.318 mm diameter was cold expanded by using a mandrel, resulting in a degree of expansion 1.47%. A significant amount of compressive tangential residual stress of 502 MPa at the hole surface was calculated using the finite element analysis and the compressive residual stress was more widely spreaded in the entry and exit planes than the mid plane in the plate thickness. The compressive tangential residual stresses showed a very beneficial influence on the fatigue life of the plate by increasing 1.2 to 2 times longer lives compared to the plate without cold expansion, depending on the applied load levels. Fatigue crack initiated and propagated at the hole surface of the mandrel entrance region, where relatively lower magnitude of compressive residual stress was found than the other region.

This study analyzes lifes and damages at automotive tie rod through the structural analyses with fatigue. The structural result of this study can be effectively utilized with the design of automotive tie rod by investigating prevention and durability against its damage.

A kart is a vehicle without the suspension system and the differential gear. The kart frame as an elastic body plays the role of a spring. By the cornering of a kart, rolling, pitching and twisting motions are induced in the kart frame. Also the slip or noncontact of the wheel and a permanent deformation of the kart frame can be induced. In order to examine closely this phenomenon of the twisting deformation, measurement and analysis on torsion working stress with strain gage and tracking system are needed. According to the measurement result, while steady state driving in a curve in general the torsion working stress of the kart frame will be increased depending on the vehicle velocity, but the kart frame will be not permanent deformed. However, analysis of the torsion working stress in comparison with torsion fatigue limit shows that while unsteady state driving as clash with same drive condition the racing kart frame will be deformed more quickly as the leisure kart frame.

This study is the measurement for fatigue cracks at U-Rib in the steel deck bridge. Thus, to analyze the causes and reinforcement methods through the measurement results. So the bridge will preserve the safety & usability and want to enhance the durability.

본 연구에서는 초박층 교면포장으로 폴리설파이드 에폭시 폴리머 콘크리트 포장을 선정하여, 에폭시 아스팔트 포장, SFRC 포장과의 비교 분석을 통해 폴리머 콘크리트 포장이 강바닥판의 피로응력범위에 어떠한 영향을 미치는 지 분석하였다. 강바닥판의 피로응력범위를 산정하기 위해 Abaqus를 사용한 유한요소해석을 사용하여 비교평가하였으며, 용접부에 교축방향 및 교축직각방향의 다축응력이 발생하는 점을 감안하여 Signed Von-Mises 응력을 도입하여 피로 검토에 활용하였다. 강바닥판의 피로응력범위를 산정하기 위해 Abaqus를 사용한유한요소해석을 사용하여 포장 재료 및 두께에 따라 비교평가하였으며, 용접부에 교축방향 및 교축직각방향의 다축응력이 발생하는 점을 감안하여 Signed Von-Mises 응력을 도입하여 피로 검토에 활용하였다.

강교의 정확한 피로균열의 발생원인 또는 교량의 피로안전성을 검토하기 위해서는 적합한 응력이력 측정이 요구된다. 그러나 실제 현장에서의 응력이력 측정은 현장 여건과 경제성, 작업성 등의 이유로 1개소의 스트레인게이지를 설치하여 계측을 실시한다. 이는 특정 구조물의 실제 치수와 게이지 길이 용접부 응력집중 등의 영향을 고려하지 못하고, 구조 모델링을 통한 응력해석에도 많은 어려움이 있다. 그러므로 본 연구에서는 용접단부에 다수의 게이지 설치, 최소 길이 게이지 사용, 설치 위치 등의 개선된 방법을 적용하여 용접단부와 스트레인게이지 설치 거리에 따른 변형률 진폭에 대한 상관식을 도출하고 국제용접협회 (IIW)의 제안식과 비교하였다. 또한 적합한 피로등급 상세범주 선정을 통해 공용중인 교량의 피로손상도 평가 및 잔존수명을 예측하고 분석하였다. 그 결과 피로균열 발생빈도가 높은 부재파악, 용접단부와 게이지 설치 거리에 따른 변형률의 정량적 파악으로 정확한 피로손상도 평가 및 잔존수명 예측이 가능하므로 향후 교량의 응력이력계측 시 개선된 방법을 적용해야 할 것이다.

Steel deck plate is a preferable structure in the long span bridge construction because of the weight decrease and the aesthetic enhancement. But its orthogonal anisotropic structure is connected with various subsidiary materials so that the fatigue transfer is complex. This study will be conducted with the a few strain gauge is installed in the weak range of hot spot stress where the actual fatigue crack is anticipated and will compare it with the fatigue crack range and the allowable fatigue stress category of the steel deck plate in home and abroad

In general, to conduct the fatigue evaluation of the steel bridge, the performance test is conducted with the strain gauge where the fatigue crack is generated, or where the geometric influences are made by the structural features. But this test does not consider the actual size of the specific structure and the length of the gauge so that it`s difficult to analyze the result, though the stress analysis is performed. Therefore, this study will be conducted with the strain gauge is installed in the weak range of hot spot stress where the actual fatigue crack is anticipated, will make the regression equation of the strain, and will compare it with the strain equation suggested from IIW .