Graphene, a new material with various advantageous properties, has been actively used in various fields in recent years. Applications of graphene oxide are increasing in combination with other materials due to the different properties of graphene oxide, depending on the number of single and multiple layers of graphene. In this study, single-layer graphene oxide and multi-layer graphene oxide are spray coated on polystyrene, and the physicochemical properties of the coated surfaces are characterized using SEM, Raman spectroscopy, AFM, UV-Vis spectrophotometry, and contact angle measurements. In singlelayer graphene oxide, particles of 20 μm are observed, whereas a 2D peak is less often observed, and the difference in surface height increases according to the amount of graphene oxide. Adhesion increases with an increase in graphene oxide up to 0.375 mg, but decreases at 0.75 mg. In multi-layer graphene oxide, particles of 5 μm are observed, as well as a 2D peak. According to the amount of graphene oxide, the height difference of the surface increases and the adhesive strength decreases. Both materials are hydrophilic, but single-layer graphene oxide has a hydrophilicity higher than that of multi-layer graphene oxide. We believe that multi-layer graphene oxide and single-layer graphene oxide can be implemented based on the characteristics that make them suitable for application.

The effect of multi-walled carbon nanotubes (MWCNT) coating in the presence of polyethyleneimine (PEI) of different molecular weights (MW) on the interfacial shear strength (IFSS) of carbon fiber/acrylonitrile–butadiene–styrene (ABS) and carbon fiber/epoxy composites was investigated. The IFSS between the carbon fiber and the polymer was evaluated by means of single fiber microbonding test. The results indicated that uses of the carbon fibers uncoated and coated with pristine, low MW PEI-treated, and high MW PEI-treated MWCNT significantly influenced the IFSS of both thermoplastic and thermosetting carbon fiber composites as well as the carbon fiber surface topography. The incorporation of low MW (about 1300) PEI into the carboxylated MWCNT was more effective not only to uniformly coat the carbon fiber with the MWCNT but also to improve the interfacial bonding strength between the carbon fiber and the polymer than that of high MW (about 25,000) PEI. In addition, carbon fiber/epoxy composite exhibited the IFSS much higher than carbon fiber/ABS composite due to the chemical interactions between the epoxy resin and amine groups existing in the PEI-treated MWCNT.

Ti-Al-Si target and Cr-Si target are sputtered alternately to develop a multi-layered nitride coating on a steel mold to improve die-casting lifetime. Prior to the multi-layer deposition, a CrN layer is developed as a buffer layer on the mold to suppress the diffusion of reactive elements and enhance the cohesive strength of the multi-layer deposition. Approximately 50 nm CrSiN and TiAlSiN layers are deposited layer by layer, and form about three μm-thickness of multi-layered coating. From the observation of the uncoated and coated steel molds after the acceleration experiment of liquid metal injection casting, the uncoated mold is severely eroded by the adhesion of molten metallic glass. On the other hand, the multi-layer coating on the mold prevents element diffusion from the metallic glass and mold erosion during the experiment. The multi-layer structure of the coating transforms the nano-composite structured coating during the acceleration test. Since the nano-composite structure disrupts element diffusion to molten metallic glass, despite microstructure changes, the coating is not eroded by the 1,050 oC molten metallic glass.

본 연구는 손상된 선박용 절탄기 핀튜브에 대하여 보수를 목적으로 Inconel 625 아크 열용사 코팅기술 적용 후 실링처리를 실시하였다. 모재(Substrate), 열용사 코팅(Thermal Srpay Coating; TSC) 그리고 열용사 코팅+실링처리(TSC+Sealing) 시편에 대하여 내구성을 평가하기 위해 ASTM G76-05에 의거하여 고상입자 침식(Solid Particle Erosion; SPE) 실험을 실시하였다. 표면 손상 형상은 주사전자현미경과 3D 레이져 현미경을 통해 관찰했으며, 무게 감소량과 표면 거칠기 분석을 실시하여 내구성을 평가하였다. 그 결과 내구성은 TSC와 TSC+Sealing에 비해 Substrate가 우수하게 나타났으며, 이는 TSC 층 내에 존재하는 다수의 기공 결함에 기인한 것으로 판단된다. 또한 고상 입자 침식 손상 메카니즘은 Substrate의 경우 연성 재질 특성인 소성변형과 피로에 의한 균열 생성이 동반되었으며, TSC와 TSC+Sealing의 경우 취성파괴 경향이 확인되었다.

In this study, by using a system analysis program(Fluid Flow), the correlation between the location where cladding damage occurs frequently inside the power plant seawater pipe and flow characteristics is analyzed, and the root cause and improvement plan are reviewed. As a result, it was confirmed that a high flow velocity occurred in the backwash piping(7.64m/s) and the front and rear ends of the flow control valve(5.93m/s). In addition, it was confirmed that cavitation occurs when the seawater level decreases below the saturated water vapor pressure at the rear end of the orifice. These areas are locations where the internal cladding damage occurs frequently in power plants, and the main cause of damage is considered to be excessive flow velocity and cavitation in the pipe. In order to solve this problem, improvement method such as installation of backwash pipe orifices, change of pipe shape at the front and rear end of flow control valve, and change of orifice type were derived.

The SnSe single crystal shows an outstanding figure of merit (ZT) of 2.6 at 973 K; thus, it is considered to be a promising thermoelectric material. However, the mass production of SnSe single crystals is difficult, and their mechanical properties are poor. Alternatively, we can use polycrystalline SnSe powder, which has better mechanical properties. In this study, surface modification by atomic layer deposition (ALD) is chosen to increase the ZT value of SnSe polycrystalline powder. SnSe powder is ground by a ball mill. An ALD coating process using a rotary-type reactor is adopted. ZnO thin films are grown by 100 ALD cycles using diethylzinc and H2O as precursors at 100oC. ALD is performed at rotation speeds of 30, 40, 50, and 60 rpm to examine the effects of rotation speed on the thin film characteristics. The physical and chemical properties of ALD-coated SnSe powders are characterized by scanning and tunneling electron microscopy combined with energy-dispersive spectroscopy. The results reveal that a smooth oxygenrich ZnO layer is grown on SnSe at a rotation speed of 30 rpm. This result can be applied for the uniform coating of a ZnO layer on various powder materials.

Iron-based amorphous powder attracts increasing attention because of its excellent soft magnetic properties and low iron loss at high frequencies. The development of an insulating layer on the surface of the amorphous soft magnetic powder is important for minimizing the eddy current loss and enhancing the energy efficiency of highfrequency devices by further increasing the electrical resistivity of the cores. In this study, a hybrid insulating coating layer is investigated to compensate for the limitations of monolithic organic or inorganic coating layers. Fe2O3 nanoparticles are added to the flexible silicon-based epoxy layer to prevent magnetic dilution; in addition TiO2 nanoparticles are added to enhance the mechanical durability of the coating layer. In the hybrid coating layer with optimal composition, the decrease in magnetic permeability and saturation magnetization is suppressed.

본 연구에서는 폴리비닐알콜(PVA)와 폴리프로필렌글리콜(PPG)기반의 창상피복용 수분산 폴리우레탄수지를 합성하였으며, 시료의 물리적 특성을 필름 시료와 피혁(Full-Grain) 표면에 코팅을 하여 물리적 특성 변화를 연구하였다. 인장강도의 경우 PVA가장 적게 반응된 PUD-PA1 2.00 kgf/㎟ 으로 가장 높은 저항성을 보였으며. 마찬가지로 연실율은 PVA가장 적게 반응된 PUD-PA1가 554%로 높게 측정되었다. 내마모성 측정 결과 PVA 반응이 증가함에 따라 표면의 강도나 낮게 36.77 ㎎.loss로 감소 됨을 알수 있었다.

Transparent, photocatalytic, and self-cleaning TiO2 thin film is developed by TiO2 sol-gel coating on glass and polycarbonate (PC) substrates. Acetyl acetone (AcAc) suppresses the precipitation of TiO2 by forming a yellowish (complex) transparent sol-gel. XPS analysis confirms the presence of Ti2p and O1s in the thin films on glass and PC substrates. The TiO2- sol is prepared by stabilizing titanium (IV) isopropoxide (TTIP) with diethylamine and methyl alcohol. The addition of AcAcsilane coupling solution to the TiO2-sol instantaneously turns to yellowish color owing to the complexing of titanium with AcAc. The AcAc solution substantially improves the photocatalytic property of the TiO2 coating layer in MB solutions. The coated TiO2 film exhibits super hydrophilicity without and with light irradiation. The TiO2 thin film stabilized by adding 8.7 wt% AcAc shows the highest photo-degradation for methylene blue (MB) solution under UV light irradiation. Also, the optimum photocatalytic activity is obtained for the 8.7 wt% AcAc-stabilized TiO2 coating layer calcined at 450 oC. The thin-films on glass exhibit fast self-cleaning from oleic acid contamination within 45 min of UV-light irradiation. The appropriate curing time at 140 oC improves the anti-fogging and thermal stability of the TiO2 film coated on PC substrate. The watermark-free PC substrate is particularly beneficial to combat fogging problems of transparent substrates.

In this research, carbon nanotubes(CNT) and graphene nanoplates(GnP) are deposited on the surface of carbon fibers(CF) at once. Investigating the effect between CNT and GnP on increasing the interfacial and mechanical properties of carbon fiber reinforced epoxy composites(CFRP). The cross section of the CFRP composites indicates that the GnPs/CNTs hybrid coating exhibits significantly higher mechanical performance in all coating samples. The interlayer shear strength of the GnPs/CNT hybrid coated CFRP composite was 90% higher than that of the uncoated CF composite. The flexural and tensile strength of CFRP composites using GnPs /CNT hybrid coatings were improved by 52% and 70%, respectively, compared to uncoated CF.

This study is aimed at preparing and evaluating the plasma resistance of YAS (Y2O3-Al2O3-SiO2) coating layer with crystalline YAG phase contents. For this purpose, YAS frits with controlled phase contents are prepared and melt-coated on sintered Al2O3 ceramics. Then, the results of phase analysis of crystalline YAS coating layer are compared to that of YAS frits, and discussed with regard to the plasma resistance of the YAS coating layer. The phase contents of the YAS frit change in a manner different from that of the prepared YAS coating layer, presumably owing to the composition change of YAS frit during the melt-coating process. The plasma resistance of the YAS coating layer is shown to increase with the YAG phase contents in the coating layer. Comparing the weight loss of YAS coating layer with those of commercial Y2O3, Al2O3, and quartz ceramics, the plasma resistance of the prepared YAS coating layer is 8 times higher than that of quartz and 3 times higher than that of Al2O3; this layer shows 70 % of the resistance of Y2O3.

In this paper, graphene-coated Al powders prepared by in situ reduction method were directly used for cold spraying, obtaining a graphene-reinforced Al matrix composite coating with more compact structure and better performance. Cross-sectional analysis revealed that compared with the pure Al powders, the graphene-coated Al powders were more severely deformed, and the resulting coating was denser and its porosity was reduced by over 80%. The hardness of the graphene-coated Al coating was increased by 40%, and its brine immersion time was prolonged by nearly three times. However, the graphene increases the pitting sensitivity of the Al coating; so, the enhanced corrosion resistance of the graphene-coated Al coating is mainly attributed to the improvement of its structure densification.

This study is aimed at improving the plasma resistance of Al2O3 ceramics on which plasma resistant YAS(Y2O3- Al2O3-SiO2) frit is melt-coated using a simple heat-treatment process. For this purpose, the results of phase analysis and microstructural observations of the prepared YAS frits and the coating layers on the Al2O3 ceramics according to the batch compositions are compared and discussed with regard to the results of plasma resistance test. The prepared YAS frits consist of crystalline or amorphous or co-existing crystalline and amorphous phases according to the batch compositions, depending on the role and content of each raw material. The prepared YAS frit is melt-coated on the densely sintered Al2O3 ceramics, resulting in a dense coating layer with a thickness of at least ~ 80 m. The YAS coating layer consists of crystalline YAG(Y3Al5O12), Y2Si2O7, and Al2O3 phases, and YAS glass phase. Plasma resistance of YAS coated Al2O3 ceramics is strongly dependent on the content of the YAG(Y3Al5O12) and Y2Si2O7 crystalline phases in the coating layer, especially on the content of the YAG phase. Comparing the weight loss of YAS coating ceramics with values obtained for commercial Y2O3, Al2O3, and quartz ceramics, the plasma resistance of the YAS coating ceramics is 6 times higher than that of quartz, 2 times higher than that of Al2O3, and 50 % of the resistance of Y2O3.

In the automotive industry, the platinum titanium anodes (Pt/Ti anode) play a significant role in electroplating of chromium coating on the vehicle’s shock absorber piston rod. In this paper, the structure of Pt/Ti anode was designed to obtain high quality and save time for the electroplating process. The structure of anode was designed in 2D & 3D modeling and analyzed by CATIA and ABAQUS program, respectively. The structural modeling of the anode was analyzed and carried out using a finite element method (FEM) by applied various loads. The manufacture anodes were installed in an electroplating bath in order to test the efficiency of chromium coating on shock absorber piston rod and safety of anode structure. The results presented indicate that the structural analysis is safe after applied loads due to the allowable stress is higher than the maximum equivalent stress about 4 times, and the chromium coating test obtained high-efficiency results.

A T-800 (Co-Mo-Cr) coating material is fabricated using Co-Mo-Cr powder feedstock and laser cladding. The microstructure and melted Al erosion properties of the laser-cladded T-800 coating material are investigated. The Al erosion properties of the HVOF-sprayed MoB-CoCr and bulk T-800 material are also examined and compared with the laser-cladded T-800 coating material. Co and lave phases (Co2MoCr and Co3Mo2Si) are detected in both the lasercladded T-800 coating and the bulk T-800 materials. However, the sizes of the lave phases are measured as 7.9 μm and 60.6 μm for the laser-cladded and bulk T-800 materials, respectively. After the Al erosion tests, the erosion layer thicknesses of the three materials are measured as 91.50 μm (HVOF MoB-CoCr coating), 204.83 μm (laser cladded T- 800), and 226.33 μm (bulk T-800). In the HVOF MoB-CoCr coating material, coarse cracks and delamination of the coating layer are observed. On the other hand, no cracks or local delamination of the coating layer are detected in the laser T-800 material even after the Al erosion test. Based on the above results, the authors discuss the appropriate material and process that could replace conventional bulk T-800 materials used as molten Al pots.

본 논문은 수산물에 사용되는 식용 코팅의 다양한 천연 성분에 대한 소재 및 특성에 대하여 조사하였으며, 화학적 항균 물질 및 항산화제와 물리적 살균 기술을 병합한 허들 기술(hurdle technology)에 대하여 서술하였다. 다양 한 원인으로 인한 식중독 사고가 빈번히 발생하고 있으며 주된 원인은 오염된 식품의 섭취와 관련이 있다. 특히, 식품 중에서도 수산물은 수분함량이 많고 미생물에 오염되기 쉽기 때문에 저장 기한이 짧다. 이에 대한 해결방안으 로 여러 가지 대안들이 적용되고 있는데, 가식성을 가지 고 독성이 없는 장점을 가진 식용 코팅이 주목을 받고 있다. 식용 코팅은 미생물의 성장을 억제하고 수분 손실을 지연시킴으로써 수산물의 품질을 유지할 수가 있다. 또한 항균 물질 및 항산화제를 첨가하거나 물리적인 살균 기술과도 병합할 수 있다. 하지만 식용 코팅과의 병합 처리 기술이 소수 보고되고 있어 다양한 허들 기술에 대한 연구가 필요하다.