Interest in the use of semiconductor-based photocatalyst materials for the degradation of organic pollutants in a liquid phase has grown, due to their excellent performance and response to the light source. Herein, we fabricated a NiO-SiCTiO2 ternary structured photocatalyst which had reduced bandgap energy, with strong activation under UV-light irradiation. The synthesized samples were examined using XRD, SEM, EDX, TEM, DRS, EIS techniques and photocurrent measurement. The results confirmed that the two types of metal oxides were well bonded to the SiC fiber surface. The junction of the new photocatalyst exhibited a large number of photoexcited electrons and holes. The holes tended to oxidize the water and form a hydroxyl radical, which promoted the decomposition of methylene blue. The close contact between the 2D SiC fiber and metal oxide semiconductors expanded the scope of absorption wavelength, and enhanced the usability of the ternary photocatalyst for the degradation of methylene blue. Among three synthesized samples, the NiO-SiC-TiO2 showed the best photocatalytic effect, and was considered to have excellent photoelectron transfer due to the synergy effect between the metal oxide and SiC.

To solve the problem of water pollution, researchers have proposed a photocatalytic degradation technology, in which the key factor is the development of efficient photocatalytic materials. Graphitic carbon nitride (g-C3N4), an n-type semiconductor, has been widely studied due to its suitable band gap (2.7 eV), low cost, easy preparation, non-toxicity, and high photostability. However, the pure-phase g-C3N4 still has defects such as low specific surface area, insufficient visible light absorption, low charge mobility, few active sites for interfacial reaction, and easy recombination of photogenerated electron–hole pairs, which leads to the lower photocatalytic activity of g-C3N4. Aiming at the problems mentioned above, this paper focus on the synthesis of g-C3N4-based composites with high photocatalytic activity via lemon juice induction method. Thiourea and lemon juice were selected as precursors, and carbon quantum dots (CQDs) as electron mediators were introduced anchoring on the surface of g-C3N4 to build g-C3N4/CQDs with compact interface. The results showed that small-sized CQDs are uniformly distributed on the surface of g-C3N4, and the g-C3N4/CQDs composite has a 2D0D structure, which reduces the recombination of photogenerated electron–hole pairs. The photocatalytic degradation efficiency of 4% g-C3N4/CQDs for RhB reaches the highest data of 90.9%, and the photocatalytic degradation rate is 0.016 min− 1, which is about 2.3 times that of g-C3N4. After four cycles of photocatalytic reaction, the photocatalytic degradation efficiency of the material remained at 81.7%. Therefore, the g-C3N4/CQDs synthesized via lemon juice induction has a more stable microstructure, and the charge separation efficiency is greatly improved, which is suitable for practical photocatalytic environmental protection.

활성 의약품 성분(APIs)의 존재가 수생 생태계와 인간의 건강에 위험하다는 증거가 있다. 물에 항생물질인 테트 라사이클린과 같은 API가 존재하면 미생물에 항균제 내성(AMR)이 발생해 개인과 사회에 막대한 비용이 발생한다. TiO2 또 는 비스무트 기반 촉매와 같은 촉매가 내장된 막은 유기 유출물을 분해하고 폐수로부터 분리한다. 촉매의 광촉매 활성은 귀 금속 도핑 및 탄소성 물질의 첨가 및 다른 반도체와의 헤테로 접합 형성으로 향상될 수 있다. 광촉매의 회수는 고분자 막에 서 광촉매의 고정화를 통해 가능하다. 이 검토에서는 물 속 항생제의 분해가 논의된다.

Low- and intermediate-level radioactive wastes have been disposed of in the first-phase deep underground silo disposal at Gyeongju in South Korea. These radioactive wastes contain harmful radionuclides such as Uranium-238 (238U), which can pose long-term and deleterious effects on humans and the natural environment. Ethylenediaminetetraacetic acid and isosaccharinic acid, which can be formed via cellulosic waste degradation under high alkaline conditions might considerably enhance the transport behavior of 238U with the intrusion of rainwater and groundwater. In this study, the engineered barriers (concrete and grout) and natural barriers (sedimentary rock and granite) were used to investigate the 238U transport behavior in artificial cementitious porewater of State I (pH 13.3) and State II (pH 12.5) based on groundwater or rainwater. The surface properties and geochemical compositions of barrier samples were characterized using XRD, XRF, SEM-EDX, and BET. The transport behaviors of 238U in various solution conditions were observed by sorption distribution coefficient (Kd) at a range of initial chelating agents concentration (10-5-10-2 M). The sorption behavior of 238U was retarded more in the engineered rock barriers than in the natural rock barriers. The mobility enhancement of 238U was more significant in State I than in State II. In comparison with the absence of chelating agents, negligible changes in the Kd values of 238U were observed at less than initial chelating agent concentrations of 10-4 M. However, the Kd values of 238U were significantly reduced at initial chelating agent concentrations higher than 10-3 M. Therefore, these experimental findings show that the transport behavior of 238U into the geo- and bio-sphere could be accelerated by the presence of chelating agents and the type of cement degradation states.

Cellulose-based wastes can be degraded into short-chain organic acids at the cementitious radioactive waste repository. Isosaccharinic acid (ISA), one of the main degradation products, can form the chelate complex with metals and radionuclides, and these complexes have a potential that can accelerate to move the radionuclides to far-field from the repository. This study characterized the amount of generated ISA from typical cellulosic materials in the repository. Two different degradation experiments were conducted under alkaline conditions (saturated with Ca(OH)2 at pH 12.4): i) cellulosic material mixture under an opened condition (partially aerobic), and ii) cellulosic material under an anaerobic condition in a nitrogen-purged glove box. In the first case, three different types of cellulosic materials–paper, cotton, and wood– were mixed at the same ratio, and the experiments were carried out at three different temperatures (20°C, 40°C, and 60°C). It revealed that both the cellulose degradation rate and generated ISA concentration were high at high reaction temperatures, and various soluble degradation products such as formic acid and lactic acid were generated. The cellulose degradation in this work seems to still stay at a peeling-off process. In the second study, each type of cellulosic material was applied in its own batch experiments, and the amount of generated ISA was in the order of paper > wood > cotton. The above two experiments are supposed to be a long-term study until the generated ISA reaches an equilibrium state.

Maintaining fuel sheath integrity during dry storage is important. Intact sheath acts as the primary containment barrier for both fuel pellets and fission products over the dry storage periods and during subsequent fuel handling operations. In KNF, in-house fuel performance code was developed to predict the overall behavior of a fuel rod under normal operating conditions. It includes the analysis modules to predict temperature, pellet cracking and deformation, sheath stress and strain at the mid-plane of the pellet and pellet-pellet interfaces, fission gas release and internal gas pressure. The main focus of the code is to provide information on initial conditions prior to dry storage, such as fission gas inventory and its distribution within the fuel pellet, initial volumes of storage spaces and their locations, radial profile of heat generation within the pellet, etc. To upgrade the developed code that address all the damage mechanisms, the first step was a review of the available technical information on phenomena relevant to fuel integrity. Potential degradation mechanisms that may affect sheath integrity of CANDU spent fuel during dry storage are: creep rupture under internal gas pressure, sheath oxidation in air environment, stress corrosion cracking (SCC), delayed hydride cracking (DHC), and sheath splitting due to UO2 oxidation for a defective fuel. The failure by creep rupture, SCC or DHC is in the form of small cracks or punctures. The failure by sheath oxidation or sheath splitting due to UO2 oxidation results in a gross sheath rupture. The second step was to examine the technical bases of all modules of the in-house code, identify and extend the ranges of all modules to required operating ranges. This step assessed the degradation mechanisms for the fuel integrity. The objective of this assessment is to predict the probability of sheath through-wall failure by a degradation mechanisms as a function of the sheath temperature during dry storage. Further improvements being considered include upgrades of the analysis module to achieve sufficient accuracy in key output parameters. The emphasis in the near future will be on validation of the inhouse code according to a rigorous and formal methodology. The developed models provide a platform for research and industrial applications, including the design of fuel behavior experiments and prediction of safe operating margins for CANDU spent fuel.

The skeleton of fuel assembly is composed of top nozzle, bottom nozzle, grids, and guide tubes. In the reactor core, all the parts of the fuel assembly suffer degradations due to the condition of high temperature, pressure and water environment. Therefore, many material properties of high temperature mechanical strength, corrosion and irradiation resistance have been considered to choose the material for fuel assembly parts in the fuel development stage. The guide tubes have important roles to connect each parts and support the load of fuel assembly while the fuel is lifted. In Westinghouse 14×14 standard fuel assembly, Zircaloy-4 was used for the material of the guide tubes. Zircaloy-4 has a resistance to water corrosion and maintain good mechanical properties after the discharge from the core, so this alloy is also utilized for a fuel rod cladding material although the microstructure is slightly different due to the heat treatment difference. Thus, it is expected that there is no issue regarding the guide tube integrity after the discharge and during the storage in the pool, especially in case of low burn-up. However, the surface oxidation and resultant hydrogen pick-up can affect to the embrittlement to the Zr alloy. So, it is needed to know the actual status of spent fuel assembly by performing post-irradiation examination. In this study, the degradation level of the guide Tubes in low burn-up spent fuel assembly was investigated using the KAERI PIE facility in order to make some data which can be utilized to the baseline for evaluating the integrity of the spent fuel skeleton.

The ZnO–Na2Ti6O13 composites were synthesized by facile solution combustion method with different molar concentrations of sodium titanate which is prepared by hydrothermal route. The formation of the composites was confirmed by the X-ray diffraction (XRD) analysis. Field emission scanning electron microscope (FESEM) and transmission electron microscope (TEM) results revealed that the synthesized composites exhibit porous morphology, whereas the pristine Na2Ti6O13 nanoparticles have whisker like morphology. Diffuse reflectance spectroscopy (DRS) and photoluminescence (PL) studies were utilized to compute the bandgap and the presence of defects in the composites respectively. The photocatalytic activity of ZnO–Na2Ti6O13 catalyst was investigated through the degradation of 4-nitrophenol under solar light over a period of 180 min and the composite with 0.05 M of Na2Ti6O13 showed higher degradation efficiency (96%) than the other concentrations of Na2Ti6O13 and pristine ZnO. The reduced bandgap, high charge transfer, more oxygen vacancies and the production of high superoxide anion radicals have profound effect on the higher photocatalytic efficiency of the composite with 0.05 of M Na2Ti6O13.

수용액에서 EBT의 분해는 pH, Ferrate (VI) 투입량, 초기 농도, 수용액 온도 등 다양한 변수의 조건에서 연구되었다. 최대 분해 효율은 pH 7.0에서 95.42%가 달성되었으며, 이 실험 조건에서 얻은 kapp 값은 872.87 M-1s-1 이었다. EBT 분해율은 Ferrate (VI)의 투입량이 증가함에 따라 증가하였으며 EBT 초기 농도가 감소함에 따라 EBT 분해의 초기 속도 상수가 증가하였다. 또한 EBT의 분해율은 온도가 10°C에서 45°C에 도달할 때까지 수용액의 온도에 따라 증가하였으며 이 실험조건에서 활성화 에너지 값은 EBT 분해에 대해 11.9 kJ/mol의 값이 도출되었다. 따라서 분해 실험의 결과는 Ferrate (VI)가 수용액상에서 EBT를 효과적으로 분해시킬 수 있음을 보여주고 있다.

Pleurotus eryngii, a white rot fungus, produces two extracellular lignin-degrading enzymes, laccase and manganese peroxidase (MnP). Owing to these enzymes, P. eryngii efficiently degrades synthetic chemicals such as azo, phthalocyanine, and triphenyl methane dyes. In this study, we investigated the degradation processes of four aromatic dyes, congo red (CR), methylene blue (MB), crystal violet (CV), and malachite green (MG), by P. eryngii under solid and liquid culture conditions. CR and MG were the most quickly degraded under solid and liquid culture conditions, respectively. However, compared to CR, CV, and MG, MB was not degraded well under both culture conditions. The activities of ligninolytic enzymes (laccase and MnP) were also investigated. Laccase was identified to be the major enzyme for dye degradation. A positive relationship between decolorization and enzyme activity was observed for CR, MB, and CV degradation. In contrast, decolorization of MG ensued after high enzyme activity. These results indicate that the degradation process differs between MG and the other aromatic dyes. Therefore, P. eryngii could be a potential tool for the bioremediation of synthetic aromatic dye effluent.

Recently, concern regarding disposal of cellulosic material is growing as cellulose is known to produce complexing agent, isosaccharinic acid (ISA), upon degradation. ISA could enhance mobility of some radionuclides, thus increasing the amount of radionuclide released into the environment. Thus, evaluation on the possible impact of the cellulose degradation would be an important aspect in safety evaluation. In this paper, safety assessments conducted in Sweden and UK are studied, and the factors required to be considered for appropriate safety assessment of cellulose is analyzed. SKB (Sweden) conducted safety assessment of cellulose degradation as a part of long-term safety assessment of SFR. SKB determined that ISA would impact sorption of trivalent and tetravalent radionuclides (Eu, Am, Th, Np, Pa, Pu, U, Tc, Zr and Nb) at concentration higher than 10−4–10−3 M, and impact sorption of divalent radionuclides (Ni, Co, Fe, Be and Pb) at concentration higher than 10−2 M. Then, SKB conservatively set the upper limit of ISA concentration to be 10−4 M and conducted cellulose degradation evaluation on each waste package type, considering the expected disposal environment of SFR. Based on the calculated results, some of the waste packages showed concentration of ISA to be higher than 10−4 M, so SKB conservatively developed waste acceptance criteria to prevent ISA being produced to an extent of affecting the safety of the repository. SKB conducted safety assessment only for the repositories with pH above 12.5 and excluded 1BLA from the safety assessment as the expected pH of 1BLA is around 12, which is insufficient for cellulose to degrade. However, SKB set disposal limit for 1BLA as well, to minimize potential impact in future. Serco (UK) conducted safety assessment of cellulose degradation for the conceptual repository, which is a concrete vault with cementitious backfill. Serco estimated that the pH of repository would maintain around 12.4. Serco conservatively assumed that the pH would be sufficient for cellulose degradation to occur partially, and suggested application of appropriate degradation ratio for safety assessment of cellulose degradation. To conduct appropriate safety assessment of cellulose degradation, an appropriate ISA concentration limit based on radionuclide inventory list, and an appropriate cellulose degradation ratio based on the pH of disposal environment should be determined. As for guidance, below pH 12.5, cellulose degradation is not expected, and between pH 12.5–13, partial cellulose degradation is expected. In future, this study could be used as fundamental data to evaluate safety of the repository.

Tributyl phosphate (TBP) is a well-known and important compound in the nuclear industry for the nuclear fuel reprocessing, and it is also used in a various field such as plastic industry as antifoaming agent. Untreated organic pollutants in TBP can remain in the soil water and cause serious environmental pollution, thus it should be degraded through environmentally friendly methods. The non-thermal plasma-based advanced oxidation process (AOP) is one of the most widely studied and best developed processes owing to its simple structure and ease of operation. In this study, a plasma-based AOP was stably generated using submerged multi-hole dielectric barrier discharge (DBD) and applied to relatively high concentration of TBP solution. A submerged DBD plasma system was designed to directly interact with water, thereby producing reactive oxygen species (ROS) and functioning as a powerful oxidizer. Additionally, UV, O3, and H2O2 are generated by the developed plasma system without using any other additives to produce OH radicals for degrading organic pollutants; therefore, this system circumvents the use of complex and advanced oxidation processes. The electrical properties and concentrations of the active species were analyzed to establish optimal plasma operating conditions for degrading TBP solution. The results were analyzed by measuring the total organic carbon (TOC) and changes in solution properties. Based on these results, a degradation mechanism of TBP solution is proposed. After 50 min of plasma treatment, the concentration of TOC was gradually decreased. Consequently, we found that plasma-based AOP using submerged multi-hole DBD has advantages as an alternative technology for degrading organic pollutants such as TBP solution.

Mechanism and kinetics of Rhenium complexes as a surrogate of Technetium-99 (99Tc) is worthy of study from radioactive waste safe disposal perspective. Re(IV)-EDTA was synthesized via the reduction of Re(VII) with Sn(II) in the presence of Ethylenediaminetetracetic acid (EDTA). The Re(IV)-EDTA was then degraded by H2O2 (7–30%) at pH of 3–11 in ionic strength I = 0–2 M solution. The Re- EDTA was observed to degrade more rapidly at pH of ≤ 3–4 than one of ≥ 10–11 and remained stable at pH = 7–9. At a low acidic pH, the complex degradation process was facilitated by protonation and corresponded to the exponential model (y = k. e–nt). In contrast, at an alkaline pH, the degradation was facilitated OH– complexation with Re(IV) and corresponded to a linear model (y = –mt + C). Complex degradation followed the zero-order rate kinetics for the H+ and Re-EDTA parameters, apart from a pH of 3, for which degradation was a better fit to first order kinetics. A higher Re(IV)-EDTA stability at a pH of 7–9 demonstrated that Re(IV)-EDTA (or 99Tc(IV)-EDTA) tends to be more persistent in natural environmental conditions.

In this study, five different Lentinula edodes cultivar (Chamaram, Sanbaekhyang, Sanjo 713ho, Sanjo 715ho, Sanjo 718ho) were evaluated for their ability to decolorize Remazol Brilliant Blue R (RBBR) in MEB medium, respectively. Chamaram and Sanjo 713ho decolorized RBBR rapidly in MEB medium within 3 and 5 days. The activities of manganese peroxidase (MnP) and laccase were determined on the MEB medium with and without lignin. Sanjo 713ho resulted the highest ligninolytic enzyme activities on incubation day 1, indicating of 1,213 U/mg of MnP activity and 1,421 U/mg of laccase activity.

일상적인 화학제품들의 사용량이 증가함에 따라 사용되었던 염료 폐기물 처리 또한 중요한 환경 적인 문제로 대두되었다. 이러한 염료폐기물은 광촉매를 이용하여 분해시킬 수 있는데, 졸-겔 기술을 활용 하면 매우 비용 효율적으로 광촉매를 합성할 수 있다. 졸-겔 기술은 나노스케일의 막 형성에도 상당히 유 용하며 간단하게 다층구조를 형성할 수도 있다. 본 연구에서는 다양한 염료 분해에 효과가 있는 산화아연 (ZnO) 이용하여 다중 회전도포 방법으로 다층구조(3층, 5층)를 가진 ZnO 막을 형성하였다. 성능비교를 위해 단일 회전도포 방법에 의한 단층구조를 가진 ZnO 막을 대조군으로 준비하였다. X선 회절분석기 및 에너지 분산 X선 분광계를 이용하여 ZnO의 구조 및 원소분석을 수행하였고, 주사전자현미경을 통해 나노 선같은 표면형상을 관찰할 수 있었다. 추가적으로 UV-Vis 분광광도계를 활용하여 자외선의 흡수도를 측정 하였다. 5층구조를 가진 ZnO 막이 단층 구조를 가진 ZnO 막에 비해 모의 메틸렌 블루를 49% 더 많이 분해하였다. 결론적으로, 다층구조를 가진 ZnO 는 메틸렌블루 염료를 더욱 효과적으로 분해하는 광촉매로 써 유용하다는 알 수 있었다.

성장하는 산업화는 심각한 수질 오염으로 이어진다. 폐수로 배출되는 약품과 섬유산업에서 나오는 유기배출물은 환경과 생명에게 악영향을 미친다. 항균치료에 사용되는 항생제가 폐수에 존재하면 인체에 매우 해로운 약제 내성균의 성장 을 야기하게 된다. 섬유산업에서 사용되는 유기염료 분자의 제조에는 다양한 유기 저분자가 사용된다. 이러한 분자들은 인쇄 및 염색 산업의 폐수 배출물에 존재하여 분해가 잘 이루지지 않는다. 이러한 문제들을 해결하기 위해 광분해성 촉매를 분리 막에 도입하고 폐수를 처리한다. 이 과정을 통해 유기 분자는 광분해되며 동시에 분해된 화합물들은 분리막을 통과하여 분리 된다. 이산화티타늄(TiO2)은 뛰어난 광촉매 역할을 하는 반도체이다. 다른 전이 금속 산화물과 화합물을 만들고 고분자 막에 도입하여 광촉매 능력을 증가시킨다. 본 총설에서는 광촉매성 분리막에 의한 염료 및 약물 분자의 분해에 대해 논의한다.

This in vitro study investigated the enhancement of rumen bacterial adhesion on a substrate to increase the digestibility of rice straw in Hanwoo cattle. The rice straw was pretreated with enzymes, probiotics, or ammonia, and the effects on the enhancement of bacterial adhesion and fiber degradation were analyzed using in vitro rumen fermentation. Enzyme treatment included spraying of cellulase and xylanase at 40 and 120 U per g of rice straw, respectively; Saccharomyces cerevisiae culture of 1.0×107 CFU was sprayed as a probiotic treatment per gram of rice straw; ammonia was sprayed at 0.3% per gram of rice straw. Following enzyme treatment, Fibrobacter succinogenes formed a higher adhesion colony than the control group (7.26±0.03 and 8.43±0.20) after 6h and 12h of in vitro culture (p<0.05), respectively. Attachment of Ruminococcus flavefaciens also increased following enzyme treatment (p<0.05) after 6 and 12 h compared to that of the control (5.18±0.06 and 6.60±0.15); and R. albus attachment showed a significant increase compared to that of the control (5.94±0.15) after 6 h of incubation (p<0.05). Probiotic treatment increased attachment of F. succinogenes in comparison with untreated rice straw after 6 h and 12 h of fermentation (p<0.05); R. flavefaciens attachment showed an increase only after 6 h of culture (p<0.05); R. albus was not affected. Attachment of F. succinogenes, R. flavefaciens, and R. albus increased with ammonia treatment after 6 h and 12 h (p<0.05). Dry matter digestibility was higher after the enzyme treatment (3.45±0.21 and 7.04±0.09) than in the control group(1.85±0.08 and 3.94±0.04) after 6 and 12 h of in vitro culture (p<0.05), respectively. It was also higher than that of untreated rice straw after probiotic and ammonia treatments (p<0.05). There was an increase in the enhancement levels of bacterial adhesion depending on the type of fibrolytic bacteria following enzyme, probiotic, and ammonia treatment. These treatments improved digestibility. This enhancement is considered to be greater following enzyme and ammonia treatments than with probiotics.