In a self-level riser, the piston rod generates hydraulic pressure while reciprocating along the pump rod, so components such as rods and valves require precise processing technology. Among them, the design of the pump rod was changed to a spiral groove method because there was a risk of poor operation during eccentricity. In this paper, the design and 3D modeling of the pump rod were conducted, and the structural stability of the core part according to the load change applied to the pump rod was confirmed.

In this study, a winch and load motion control system design method is introduced. Especially, the winch and load (moving cart) are connected with long wire rope which is extended to few kilometers long. Therefore, the rope length changes such that many dynamic parameter values are changed as well by winding and releasing the rope from the winch system. In this paper, the authors designed the control system by considering the real time parameter variation to occupy and keep good control performance continuously. The effectiveness of introduced method was evaluated by simulation results.

This paper investigates the characteristics of unstable behaviour and critical buckling load by joint rigidity of framed large spatial structures which are sensitive to initial conditions. To distinguish the stable from the unstable, a singular point on equilibrium path and a critical buckling level are computed by the eigenvalues and determinants of the tangential stiffness matrix. For the case study, a two-free node example and a folded plate typed long span example with 325 nodes are adopted, and these adopted examples' nonlinear analysis and unstable characteristics are analyzed. The numerical results in the case of the two-free node example indicate that as the influence of snap-through is bigger; that of bifurcation buckling is lower than that of the joint rigidity as the influence of snap-through is lower. Besides, when the rigidity decreases, the critical buckling load ratio increases. These results are similar to those of the folded-typed long span example. When the buckling load ratio is 0.6 or less, the rigidity greatly increases.

This study investigated characteristics of buckling load and effective buckling length by member rigidity of dome-typed space frame which was sensitive to initial conditions. A critical point and a buckling load were computed by analyzing the eigenvalues and determinants of the tangential stiffness matrix. The hexagonal pyramid model and star dome were selected for the case study in order to examine the nodal buckling and member buckling in accordance with member rigidity. From the numerical results, an effective buckling length factor of adopted models was bigger than that of Euler buckling for the case of fixed boundary. These numerical models indicated that the influence of nodal buckling was greater than that of member buckling as member rigidity was higher. Besides, there was a tendency that the bifurcation appeared on the equilibrium path before limit point in the member buckling model.

본 논문에서는 랜덤한 축대칭 기하학적 초기결함을 갖는 원통이 축방향 충격하중을 받는 경우의 반경방향 변위가 임계기준치를 최초로 통과하는 확률론적 충격좌굴 파괴시간을 해석할 수 있는 방법을 제시하였다. 랜덤한 기하학적 초기결함의 생성을 위해 초기결함의 평균함수 및 상관함수를 이용하여 확률장을 형성하는 방법을 사용하였다. 본 논문에서 제시된 방법은 실제적인 기하학적 초기결함이 갖는 불확실성을 취급하는데 적절하고 실용적이므로 이를 고려한 원통의 구조안전도해석에 이용할 수 있다.

High-strength bolt has high stiffness and fatigue strength. At this time, initial axial force is one of main factor to affect the strength and deformation behavior of connection. Therefore, the objective of this study is to investigate reduction of initial axial force in high-strength bolt under shear fatigue.

Current bridge load carrying capacity evaluation method requires FE model and field test to get the dynamic response. This paper shows a economic and convenient technique to trace the variation of the load carrying capacity of bridges, based on fundamental frequency measured under actual traffic flow.

풍향풍속계는 실시간으로 풍향과 풍속을 측정하는 기상관측기구로서 바람의 영향을 많이 받는 항만, 조선소, 해상구조물, 또는 건설현장에서 사용되는 크레인에 장착되어 작업가능 여부를 알리거나 전도 사고를 예방하기 위한 안전시스템과 연동되어 사용된다. 로드 셀형 풍향풍속계는 4개의 수풍부에 연결된 로드 셀의 하중 합을 이용하여 풍속을, 하중 비를 이용하여 풍향을 측정한다. 선행연구에 따르면, 풍향에 따른 인접한 두 수풍부의 하중 비는 날개 주위에 와류로 인해 불규칙한 값을 보이게 되며, 이는 풍향 오차를 증가시키는 원인이 된다. 본 연구에서는 이러한 오차를 줄이기 위하여 세 가지 수풍부 형상에 따른 하중 비를 분석하고, 오차를 줄일 수 있는 수풍부 형상을 제시하고자 한다. 수풍부 형상에 따른 하중 비를 비교하기 위해 ANSYS CFX를 사용하여 유동해석을 수행하였으며, 설계변수로 0도에서 90도까지 11.25도 간격으로 9가지 풍향조건을 설정하였다.