현상학 연구는 질적 연구방법 중에서도 현상의 이면을 밝혀 그 본질을 도출하는 방법론이다. 이런 본래 의 현상학적 연구의 취지를 살려 연구의 성격에 맞춰 현상의 본질을 드러낼 수 있는 다양한 현상학적 방법 론이 적용될 필요가 있다. 하지만 현상학적 방법론은 현실적으로 지오르지(Giorgi)와 반마넨(Van Manen) 의 방법론에 치우쳐 있는 실정이다. 이런 문제의식을 바탕으로 본 연구자는 청소년의 학교폭력 경험에 적용 한 현상학적 자기평가방법의 분석방법을 고찰했다. 이 방법론은 환원과정이 4단계로 구체적이어서 현상학 의 본래 취지인 본질에 도달하는데 적합하다고 생각한다. 구체적으로 학교폭력 피해학생의 심층인터뷰를 활용해 현상학적 자기평가방법의 환원과정을 이 연구에서 보여주었다. 이 현상학적 자기평가방법은 사회복 지학이나 사회학에서 다루는 현상의 본질을 파악하기에 적합한 연구방법이라 할 수 있다.

A large amount of small and medium-sized metal waste is generated during the decommissioning of nuclear power plants (NPPs). Metal waste is mostly contaminated with low-level radioactive, so it needs decontamination for self-disposal and recycling. A large amount of Organic Decontamination Liquid Waste during decontamination will be generated. The generated organic liquid waste is low in concentration, so the decomposition efficiency is low in the decomposition process. A conditioning process is necessary to concentrate at a high concentration. For effective treatment for Organic Decontamination Liquid Waste, the composition of organic liquid waste and conditioning process were analyzed. Organic acids, metal ions, radioactive nuclides, surfactants, etc. are present in the Organic Decontamination Liquid Waste, and suspended solids are sometimes generated by various reactions. According to previous studies, the concentration of organic acids including surfactants obtained results from several tens of ppm to a maximum of 1,000 ppm, so the maximum value of 1,000 ppm was assumed. For the composition and total amount of metal ions, the average value (52.7wt% Fe, 16.3wt% Ni, 15.1wt% Cr, 15.9wt% Mn) of the distribution of metal species removed by the actual decontamination process is applied, and the total amount is 1,000 ppm was assumed. As for the radionuclides, only 60Co and 137Cs, which are expected to be mainly present, were considered, and 60Co was assumed to be 2,000 Bq/g and 137Cs to be 360 Bq/g by referring to the literature. The amounts of suspended solids were assumed to be 500 ppm by referring to the characteristics of the liquid waste generated in the decontamination process of the NPPs. Based on the estimated value, a reaction formula was established and a simulated Organic Decontamination Liquid Waste was prepared. As a result of measurement using an analysis device, the composition of the estimated and simulated Organic Decontamination Liquid Waste had similar values. The conditioning and treatment process largely consists of pretreatment, conditioning, decomposition processes. Organic Decontamination Liquid Waste goes through a pretreatment process to remove impurities with large particles. In the conditioning process, treated water that has passed through the UF/RO membrane system is discharged into the environment. At this time, Concentrated water goes through a decomposition process for processing the Organic Decontamination Liquid Waste, and is discharged to the environment through a secondary RO membrane system. The conditioning process is the low-concentration Organic Decontamination Liquid Waste in the UF membrane system is forming a micelles in an RO membrane system, concentrating it to a high concentration and then go through a recirculation process in the UF membrane system. An experiment was conducted to confirm whether the concentration of surfactants occurred during the conditioning process. As a result of the experiment confirmed that the highly concentrated surfactant formed micelles and was filtered out in the UF membrane system.

The most important thing in development of a process-based TSPA (Total System Performance Assessment) tool for large-scale disposal systems (like APro) is to use efficient numerical analysis methods for the large-scale problems. When analyzing the borehole in which the most diverse physical phenomena occur in connection with each other, the finest mesh in the system is applied to increase the analysis accuracy. Since thousands of such boreholes would be placed in the future disposal system, the numerical analysis for the system becomes significantly slower, or even impossible due to the memory problem in cases. In this study, we propose a tractable approach, so called global-local iterative analysis method, to solve the large-scale process-based TSPA problem numerically. The global-local iterative analysis method goes through the following process: 1) By applying a coarse mesh to the borehole area the size of the problem of global domain (entire disposal system) is reduced and the numerical analysis is performed for the global domain. 2) Solutions in previous step are used as a boundary condition of the problem of local domain (a unit space containing one borehole and little part of rock), the fine mesh is applied to the borehole area, and the numerical analysis is performed for each local domain. 3) Solutions in previous step are used as boundary conditions of boreholes in the problem of global domain and the numerical analysis is performed for the global domain. 4) steps 2) and 3) are repeated. The solution derived by the global-local iterative analysis method is expected to be closer to the solution derived by the numerical analysis of the global problem applying the fine mesh to boreholes. In addition, since local problems become independent problems the parallel computing can be introduced to increase calculation efficiency. This study analyzes the numerical error of the globallocal iterative analysis method and evaluates the number of iterations in which the solution satisfies the convergence criteria. And increasing computational efficiency from the parallel computing using HPC system is also analyzed.

Particle morphology change and different experimental condition analysis during composite fabrication process by traditional ball milling with discrete element method (DEM) simulation were investigated. A simulation of the three dimensional motion of balls in a traditional ball mill for research on the grinding mechanism was carried out by DEM simulation. We studied the motion of the balls, the ball behavior energy and velocity; the forces acting on the balls were calculated using traditional ball milling as simulated by DEM. The effect of the operational variables such as the rotational speed, ball material and size on the flow velocity, collision force and total impact energy were analyzed. The results showed that increased rotation speed with interaction impact energy between balls and balls, balls and pots and walls and balls. The rotation speed increases with an increase of the impact energy. Experiments were conducted to quantify the grinding performance under the same conditions. Furthermore, the results showed that ball motion affects the particle morphology, which changed from irregular type to plate type with increasing rotation speed. The evolution was also found to depend on the impact energy increase of the grinding media. These findings are useful to understand and optimize the particle motion and grinding behavior of traditional ball mills.

NCS(National Competency Standards) is made by HRDKorea for real company, education, training and qualifications under the current government of national issues. It developed 836 units on the classification of KECO. But. Actual companies do not take advantage of improvements in job competency and production processes. This study is redesigned a real company production process use to some developed the NCS standards. After we finds some process problems and then searches the improve methods on analysis the problems.

In this study, we develop a method for analyzing business process based on the event-driven process chain (EPC) model. The method consists of five stages such as identifying abnormal events, finding causes for the abnormal events and problems caused by the abnormal events, making cause-and-effect chains, drawing root-cause map, and defining improvement areas. We illustrate how to apply the method with some examples for the domestic registered mail delivery process.

In recent years, safety recalls have occurred frequently in the biopharmaceutical industry, which affects the health of consumers. This article attempts to use the fsQCA method to draw a conclusion through the study of ESG and its quantification system, as well as the study of data samples related to MES and GMP processes, that is, MES-DPT has a positive impact on process safety management, and GMP-DPT has a positive impact on process safety. Management has a positive and positive impact, and ESG-DPT has a positive and positive impact on process safety management. Finally, this article puts forward suggestions for improving ESG-DPT, MES-DPT, GMP-DPT and the biomedical ESG-DPT model. Future research hopes to further study ESG -DPT model and ESG biomedical industry indicators.