Tuna purse seine fishery (TPF) constitute more than 60% of distant water fishery production in Korea based on a statistic of 2018, and 28 ships from four different companies were under operation at the western and central Pacific Ocean. On this research, common risk factors during TPF were investigated via enumeration of five years Korean fisherman’s insurance payment statement, followed by some counterplans to diminish the accident rate. The accident rate of TPF on the Pacific Ocean peaked by 43.0% in 2014 and constantly decreased to 23.0% until 2018, presenting an average of 33.6%. Meanwhile, the accident rate on the Indian Ocean reached the highest point 55.1% in 2014 and declined to 11.6% in 2016, having an average of 24.7%. The average accident rate of the Indian Ocean scored 8.9% lower than the rate of the Pacific Ocean, but no statistic significance was observed. Depending on the process of operation, ‘casting or hauling of net’ was the most frequent part that people received an injury (40.4%). When the accidents were classified by their types, ‘falling down’ was the most recurrent cause of the injuries (28.5%). At the point of severity, the worst injuries were induced by crush hazard. Considering aforementioned accident frequency and severity, all the factors on the accident type list were divided into three different groups including high risk, moderate risk, and common risk. This study is expected to contribute to the reduction of occupational accidents during the work of fishermen and establishment of a safety management system for distance water fishing vessels.

The research was analyzed the catch data of the five years (2016-2020) for six joint venture company tuna purse seiners in the Atlantic Ocean, with the aim of suggesting improvement measures for responsible and sustainable fishing according to changes of recommendation by International Commission for the Conservation of Atlantic Tuna (ICCAT) on the tropical tunas. In the last five years, the average catch of six tuna purse seiner gradually increased to 7,745 tons, 8,364 tons and 9,053 tons from 2016 to 2018, but decreased to 7,761 tons in 2019 and 6,214 tons in 2020. The reason for the decrease in fishing volume in 2019 and 2020 was the fluctuation of the formation of the cold water zone (22-23℃), and the total ICCAT convention area of FAD closure in January and February due to the expansion of the FAD closure area and poor free school catching during two months period, respectively. The analysis on fishing area showed that the percentage of fishing in the high sea was about 85% although the FAD closure area included the EEZ zone in coastal countries; the rise of the fishing license in coastal countries is also believed to be a factor. In order to overcome such situations and improve catching volume, it will be possible if excellent manpower is secured, school fishing is expanded, and the production of high value-added catch (purse seine special: PS).

우리나라에서 다랑어 선망어업은 국내 원양산업 중 업종별 생산량 1위의 업종으로, 1980년대 중 후반부터 연구가 지속적으로 수행되어왔으며, 기술의 현대화 연구가 활발히 진행되어왔다. 하지만, 어선에 탑재되는 보조작업선들은 원양어업에서 중요한 역할을 맡고 있음에도 관련 연구가 미흡한 실정이다. 이에 본 연구에서는 보조작업선들 중 네트보트의 추진기를 프로펠러에서 워터제트 형태로 변경하고, 그에 따른 선형 변환을 통한 선체 부가저항 감소 및 운항성능을 향상하고자 하였다. 이를 위해 전산수치해석을 통해서 선박의 유체 성능 변화를 계산하였으며, 또한 기존 선형 및 추진기 변화 선형에 대해 모형선 수조시험을 수행하여 속도별 저항성능 비교를 수행하였다. 수치해석 및 1/7의 축소모형의 수조시험 결과, 기존의 네트보트 대비 45~58% 저항성능이 크게 향상되었으며, 이는 철망 제거에 의한 단순 침수표면적 및 선형개선에 의한 저항성능 향상을 확인하였다.

우리나라에서는 다랑어 선망어업의 기술 경쟁력을 높이기 위한 많은 연구개발이 이루어지고 있으며, 이러한 노력으로 인하여 다랑어 선망어선의 선형개선과 어군 탐지를 위한 레이다, 소나 및 위성정보시스템의 개발로 인해 조업 효율이 향상되었다. 그러나 다랑어 선망어선에 탑재되는 보조 작업선인 스키프보트, 네트보트 및 스피드보트의 경우에는 본선의 기술 현대화에 비해 기술력이 낙후되어 있 는 실정이다. 이에 본 논문에서는 그물을 끌기 위한 양망의 기능과 프로펠러로부터 다랑어를 보호하기 위하여 설치된 철망을 가진 기존 의 네트보트의 선체를 워터제트 추진기 탑재가 가능한 선체로 변경하여 다랑어 보호, 선체저항 감소 및 운항성능 향상하고자 하였다. 결 과적으로 워터제트 형태에 적합한 선형에 대해 해양수산부 고시에 의거한 알루미늄 구조강도 기준을 적용한 시제선 제작하였으며 낙하 시험을 수행하여 안전성을 확인하였다. 또한 해상시운전을 통하여 기존의 네트보트는 2,500 RPM에서 속도는 12.0 knot, 예인력은 2,545 kgf 이며, 워터제트가 탑재된 네트보트는 3,200 RPM에서 속도는 26.7 knot, 예인력은 2,011 kgf로 워터제트가 탑재된 네트보트 또한 다랑어 선망 어선의 보조 작업선으로 예인용량 기준에 충분히 만족함을 알 수 있었다.

To suggest more efficient fishing operation, it was analyzed using five years (2011~2015) catch data of six Korean-flagged tuna purse seiners (with 1000 mt of haul capacity) operating in the western and central Pacific Ocean. In terms of annual total catch, it presented a two-year cycle of variation on catch, showing that catches of 2012, 2014 and 2015 were high, whereas those of 2011 and 2013 were low. The proportions on fishing effort of associated set were around 21.9~30.8% having 21.5~45.0% of total catch. In this study, there was no significant difference between catches of unassociated set and associated set. When considered having good fishing conditions, fishing activities were concentrated in the areas of Papua New Guinea (PNG) and Kiribati, while it showed that fishing ground spreaded out to the areas of not only PNG and Kiribati but also Federated States of Micronesia (FSM), Tuvalu and Solomon islands. The average number of fishing days was 271 with a range of 246~285. As restriction on fishing operation such as reduction of fishing days and higher fishing fee are expected to strengthen, the result of this study will be helpful to select more efficient fishing methods for purse seine fishery based on fishing conditions.

In an attempt to find the improvement of the fishing efficiency according to the hull form remodeling for the 3 tuna purse seiner, the Catch-Per-Unit-Effort (CPUE) for that undertaken before (2008) and after (2010) was analyzed. In addition, the CPUE of 6 similar ships operated same period and same fishing ground. As result, it came to verify that the three modified ships had a significant value on the CPUE. An another index for the improvement of fishing efficiency is the rate of reduction of fuel oil consumption for the modified ships. Fuel oil consumption per day in service speed as comparing with the original ships were reduced 2.1%, 4.0% and 5.1% on the modified ship A, B, and C respectively. And each ship’s service speed was increased 1.0 kt, 0.6 kt, and 0.4 kt according to the modified ship A, B, and C in due order. In the conclusion, the remodeling job with newly equipped bulbous bow, lengthened slipway and enlarged rudder area were improved fairly much on fuel oil efficiency, the ship’s speed, and in the end, that led to the improving fishing efficiency. Hence, the remodeling of tuna purse seiner come to improve not only the fishing performance, but contribute to the reduction of operating cost by saving energy for the fisheries industry.

The powered purse seine fishery is an important fishery accounting for 19.4% of adjacent water fishery production in Korea, and the commercial fishing is associated with high rate of fatal and non-fatal occupational injury. The hazard analysis for the fishermen’s safety of offshore large powered purse seiner was conducted to serve as a basic data for improving the healthy and safe working environment of fishermen using fishermen’s occupational accidents of the national federation of fisheries cooperatives (NFFC) in 2013 (n=583). As a result, the occupational accident occurrence rate of this fishery was 182.6‰ in all industries 30.9 times the rate of that. In addition, death and missing rate was found to have a very serious level management to 25.1‱ in all industries of death of 17.5 times. The accident occurred in 72.3 to 85.8% was happened at sea. The others, slipping and struck by object etc occurred more frequently in order in the frequency of accident occurrence pattern. However, the occurrence rate of death and missing did not match the frequency of accident pattern. In other words, slipping occurred frequently higher while death and missing risk was not high. And the contact with fishing gear and fall in the waters was low while death and missing risk was high. The results are expected to contribute for identification and assessment of safety hazard occurred in offshore large powered purse seiners.

In an attempt to improve the maneuvering character of hull form renovated tuna purse seiner. A renovation was carried out on the 3 tuna purse seiner fishing vessel. To grasp the progress of maneuvering and resistance on ship B (730 ton class), new bulbous bow was only attached. The ship A (740 ton class) and C (600 ton class) were modified for new bulbous bow, enlarged slipway and rudder. And then the zigzag and the turning test were carried out. According to the turning test, the advance and the tactical diameter were improved very much for the modified ship. The sea trial was carried out for the original and modified ship A. It is showed that the results of sea trial corresponded with that of the tank test on the whole. In the result of the zigzag test on ship B, the turning ability was improved very much, but the yaw checking ability was deteriorated in just some degree. In the result of the zigzag test on ship C, the turning ability and yaw checking ability were remarkably improved. Ship C was greatly improved among the three ships for the maneuvering character of modified hull form.

The purpose of this paper is to examine the roll damping characteristics by bilge keels on the fishing vessel. Unlike other degree of freedom motions, roll motion is highly nonlinear. However the quantitative evaluation of roll damping combined with waves is very important for the fishing vessel. To reduce roll motion, roll motion stabilizers such as a bilge keel is used due to easy made and cheap cost rather than anti-rolling tank and fin-stabilizer. Authors paid attention to the shape of bilge keel and waves to grasp the roll damping for the fishing vessel and studied about the difference of tendencies of roll angle following the shapes of bilge keel. The model ship was the offshore large purse seiner and four types of bilge keel were used. The data from the experiments were provided and analyzed to investigate the rolling characteristics of the model ship being affected by the wave height, wave period and bilge keel shape. The results of the study showed that three types of the bilge keel have little effective, but only one has an effect on the roll damping. So bilge keel shape and its attachment method need to be a future study for the practical use in fishing vessel.

In an attempt to respond to the increase in international oil prices and reduce operating expenses, ship remodeling was carried out on a 740ton class tuna purse seiner. To strengthen the competitiveness of the fisheries industry by improving vessel performance, a bulbous bow was newly equipped. The slipway and rudder area were also lengthened and enlarged with the propeller and main engine remained unchanged. To reduce the hull resistance, a circle type bulbous bow was attached on the hull behind bow thruster and thus the cost for exchanging electrical equipment for bow thruster was reduced. The new rudder area was expanded 15% more than the old one within the extent that the existing mechanical control part and rudder stock were not changed. To prevent fishing net damage and stabilize wake field, slipway was lengthened to the optimal position. All of the new design of remodeling parts went through the model tests in towing tank and CWC. Besides resistance test, all of necessary model test results were delivered for hydrodynamic character for the modified ship. The maneuvering simulation to verify that the remodeled ship satisfies the IMO rules was performed in both zigzag and turning tests. The estimated resistance with new bulbous bow and lengthened stern was reduced by 4.8% in the 2-dimensional analysis and 17.4% in the 3-dimensional analysis in comparison of conventional ship. The average reduction of resistance was estimated about 10%. Maneuvering character of modified hull form was found to satisfy all regulations under IMO. The remodeling of tuna purse seiner can not only improve fishing performance but also contribute to reduction of operating cost by saving energy for the fisheries industry.

The purpose of present research is to develop and efficient numerical method for the calculation of potential flow and predict the wave-making resistance for the application to ship design of tuna purse seiner. Havelock was considered the wave resistance of a post extending vertically downwards through the water from the surface, its section by a horizontal plane being the same at all depths and having its breadth small compared with its length. This enables us to elucidate certain points of interest in ship resistance. However, the ship has not infinite draft. So, the problem which is investigated ind detail in this paper is the wave resistance of a mathematical quadratic model in a uniform stream. The paper deals with the numerical calculation of potential flow around the series 60 with forward velocity by the new slender ship theory. This new slender ship theory is based on the asymptotic expression of the Kelvin-source, distributed over the small matrix at each transverse section so as to satisfy the approximate hull boundary condition due to the assumption of slender body. The numerical results using the panel shift method and finite difference method are compared with the experimental results for wigley mono hull. There are no differences in the wave resistance. However, it costs much time to compute not only wave resistance but also wave pattern over some range of Froude numbers. More improvements are strongly desired in the numerical procedure.

The purpose of the present research is to develop an efficient numerical method for the calculation of potential flow and predict the wave-making resistance for the application to ship design of tuna purse seiner. The paper deals with the numerical calculation of potential flow around the series 60 with forward velocity by the new slender ship theory. This new slender ship theory is based on the asymptotic expression of the Kelvin-source, distributed over the small matrix at each transverse section so as to satisfy the approximate hull boundary condition due to the assumption of slender body. Some numerical results for series 60, C sub(b) =0.6, hull are presented in this paper. The wave pattern and wave resistance are computed at two Froude numbers, 0.267 and 0.304. These results are better than those of Michell's thin ship theory in comparison with measured results. However, it costs much time to compute not only wave resistance but also wave pattern over some range of Froude numbers. More improvements are strongly desired in the numerical procedure.

한국 제주도와 대마도 주변해역을 중심으로 고등어와 정어리를 주어획대상으로 선단조업을 하고 있는 건착망어업의 어선의 성능, 어패의 크기, 어획성능, 조업해역별 단위노력당 어획량등을 조업어선의 톤급별로 분석, 검토한 결과는 다음과 같다. 1. 망선의 총톤수(x)와 건착망의 면적(y)간에는 y=538.8x+99657.3의 관계가 있었다. 2. CPUE의 계절변동지수는 11~4월은 기분보다 높고, 5~10월은 낮은 현상을 나타내었다. 3. 각 해역에 있어서 톤급별 어획성능지수는 톤급별, 해역별 CPUE는 1%의 유음수준에서 차가 인정되었다. 4. 톤급별 망어패의 효율은 A와 D급선 보다 B와 C급선이 높은 현상을 나타내었다

선망 어업은 우리나라 연안 어업에 있어서 매우 중요하며, 그 주 대상 어종은 고등어류이고 주 어장은 쓰시마 난류역이다. 이들의 어장과 해황과의 관계를 조사하기 위하여 크기별 고등어 어획량의 평균 분포(1974~1982)를 파악하고, 주요 어장인 제주도 동쪽 및 서쪽에 대한 해양 관측을 1983년 7월과 10월에 각각 실시하였다. 그 결과, 고등어류의 주요 어장은 역시 한국 남해의 쓰시마 난류역이었으며, 주어기는 5월과 9~10월이었다. 또 고등어류의 어획량은 체장 27~31cm(2~3세)인 소.중 고등어가 약 90%를 차지하였으나, 2~3월에는 체장 22cm (1세)의 콩 고등어가 약 40~70% 이었다. 계절적인 어장의 위치를 쓰시마 난류의 지표수인 15℃ 등온선의 북상 또는 남하 위치로 알 수 있었다. 제주도 동쪽 및 서쪽의 주어장은 쓰시마 난류수와 한국 연안수 혹은 황해 저층 냉수와의 사이에 형성되는 조경역 이었다. 또 이들 어장의 투명도 및 수색, 태양광의 투과율의 분포는 수온과 염분의 분포 및 플랑크톤 습증량의 분포와 비슷하였다.